I got my new Cisco 2811 + (NM-32A) asynchronous port module today But have a question
mgmguy1
Member Posts: 485 ■■■■□□□□□□
in CCNA & CCENT
Morming all,
I got my new Cisco 2811 with a 32 Async port module today.
I was able to fit in the module with no issue and the router seems to see the card.
Before I try to configure it I was wondering if those of you who has set up 2811 ( or 26xx) to be an access server is there anything
I should be aware of or do before I configure.
I found this website that I am using as guide to set this up
Setting up a Cisco Access Server | Router Jockey
Router info
AS2811>show ver
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 15.1(3)T
Cisco 2811 (revision 53.51) with 249856K/12288K bytes of memory.
Processor board ID FTX1116A0AU
2 FastEthernet interfaces
1 Serial interface
32 terminal lines
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
250880K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
AS2811>show line
Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 0 CTY - - - - - 0 0 0/0 -
1 1 AUX 9600/9600 - - - - - 0 0 0/0 -
1/0 66 TTY 9600/9600 - - - - - 0 0 0/0 -
1/1 67 TTY 9600/9600 - - - - - 0 0 0/0 -
1/2 68 TTY 9600/9600 - - - - - 0 0 0/0 -
1/3 69 TTY 9600/9600 - - - - - 0 0 0/0 -
1/4 70 TTY 9600/9600 - - - - - 0 0 0/0 -
1/5 71 TTY 9600/9600 - - - - - 0 0 0/0 -
1/6 72 TTY 9600/9600 - - - - - 0 0 0/0 -
1/7 73 TTY 9600/9600 - - - - - 0 0 0/0 -
1/8 74 TTY 9600/9600 - - - - - 0 0 0/0 -
1/9 75 TTY 9600/9600 - - - - - 0 0 0/0 -
1/10 76 TTY 9600/9600 - - - - - 0 0 0/0 -
1/11 77 TTY 9600/9600 - - - - - 0 0 0/0 -
1/12 78 TTY 9600/9600 - - - - - 0 0 0/0 -
1/13 79 TTY 9600/9600 - - - - - 0 0 0/0 -
1/14 80 TTY 9600/9600 - - - - - 0 0 0/0 -
1/15 81 TTY 9600/9600 - - - - - 0 0 0/0 -
1/16 82 TTY 9600/9600 - - - - - 0 0 0/0 -
1/17 83 TTY 9600/9600 - - - - - 0 0 0/0 -
1/18 84 TTY 9600/9600 - - - - - 0 0 0/0 -
1/19 85 TTY 9600/9600 - - - - - 0 0 0/0 -
Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
1/20 86 TTY 9600/9600 - - - - - 0 0 0/0 -
1/21 87 TTY 9600/9600 - - - - - 0 0 0/0 -
1/22 88 TTY 9600/9600 - - - - - 0 0 0/0 -
1/23 89 TTY 9600/9600 - - - - - 0 0 0/0 -
1/24 90 TTY 9600/9600 - - - - - 0 0 0/0 -
1/25 91 TTY 9600/9600 - - - - - 0 0 0/0 -
1/26 92 TTY 9600/9600 - - - - - 0 0 0/0 -
1/27 93 TTY 9600/9600 - - - - - 0 0 0/0 -
1/28 94 TTY 9600/9600 - - - - - 0 0 0/0 -
1/29 95 TTY 9600/9600 - - - - - 0 0 0/0 -
1/30 96 TTY 9600/9600 - - - - - 0 0 0/0 -
1/31 97 TTY 9600/9600 - - - - - 0 0 0/0 -
514 514 VTY - - - - - 0 0 0/0 -
515 515 VTY - - - - - 0 0 0/0 -
516 516 VTY - - - - - 0 0 0/0 -
517 517 VTY - - - - - 0 0 0/0 -
518 518 VTY - - - - - 0 0 0/0 -
Line(s) not in async mode -or- with no hardware support:
2-65, 98-513
I got my new Cisco 2811 with a 32 Async port module today.
I was able to fit in the module with no issue and the router seems to see the card.
Before I try to configure it I was wondering if those of you who has set up 2811 ( or 26xx) to be an access server is there anything
I should be aware of or do before I configure.
I found this website that I am using as guide to set this up
Setting up a Cisco Access Server | Router Jockey
Router info
AS2811>show ver
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 15.1(3)T
Cisco 2811 (revision 53.51) with 249856K/12288K bytes of memory.
Processor board ID FTX1116A0AU
2 FastEthernet interfaces
1 Serial interface
32 terminal lines
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
250880K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
AS2811>show line
Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 0 CTY - - - - - 0 0 0/0 -
1 1 AUX 9600/9600 - - - - - 0 0 0/0 -
1/0 66 TTY 9600/9600 - - - - - 0 0 0/0 -
1/1 67 TTY 9600/9600 - - - - - 0 0 0/0 -
1/2 68 TTY 9600/9600 - - - - - 0 0 0/0 -
1/3 69 TTY 9600/9600 - - - - - 0 0 0/0 -
1/4 70 TTY 9600/9600 - - - - - 0 0 0/0 -
1/5 71 TTY 9600/9600 - - - - - 0 0 0/0 -
1/6 72 TTY 9600/9600 - - - - - 0 0 0/0 -
1/7 73 TTY 9600/9600 - - - - - 0 0 0/0 -
1/8 74 TTY 9600/9600 - - - - - 0 0 0/0 -
1/9 75 TTY 9600/9600 - - - - - 0 0 0/0 -
1/10 76 TTY 9600/9600 - - - - - 0 0 0/0 -
1/11 77 TTY 9600/9600 - - - - - 0 0 0/0 -
1/12 78 TTY 9600/9600 - - - - - 0 0 0/0 -
1/13 79 TTY 9600/9600 - - - - - 0 0 0/0 -
1/14 80 TTY 9600/9600 - - - - - 0 0 0/0 -
1/15 81 TTY 9600/9600 - - - - - 0 0 0/0 -
1/16 82 TTY 9600/9600 - - - - - 0 0 0/0 -
1/17 83 TTY 9600/9600 - - - - - 0 0 0/0 -
1/18 84 TTY 9600/9600 - - - - - 0 0 0/0 -
1/19 85 TTY 9600/9600 - - - - - 0 0 0/0 -
Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
1/20 86 TTY 9600/9600 - - - - - 0 0 0/0 -
1/21 87 TTY 9600/9600 - - - - - 0 0 0/0 -
1/22 88 TTY 9600/9600 - - - - - 0 0 0/0 -
1/23 89 TTY 9600/9600 - - - - - 0 0 0/0 -
1/24 90 TTY 9600/9600 - - - - - 0 0 0/0 -
1/25 91 TTY 9600/9600 - - - - - 0 0 0/0 -
1/26 92 TTY 9600/9600 - - - - - 0 0 0/0 -
1/27 93 TTY 9600/9600 - - - - - 0 0 0/0 -
1/28 94 TTY 9600/9600 - - - - - 0 0 0/0 -
1/29 95 TTY 9600/9600 - - - - - 0 0 0/0 -
1/30 96 TTY 9600/9600 - - - - - 0 0 0/0 -
1/31 97 TTY 9600/9600 - - - - - 0 0 0/0 -
514 514 VTY - - - - - 0 0 0/0 -
515 515 VTY - - - - - 0 0 0/0 -
516 516 VTY - - - - - 0 0 0/0 -
517 517 VTY - - - - - 0 0 0/0 -
518 518 VTY - - - - - 0 0 0/0 -
Line(s) not in async mode -or- with no hardware support:
2-65, 98-513
"A lot of fellows nowadays have a B.A., M.D., or Ph.D. Unfortunately, they don't have a J.O.B."
Fats Domino
Fats Domino