RAI detected

binatical

I am configuring frame relay in my home lab and now it's constantly spitting out these messages on my of my routers, any help?


*Mar 8 02:23:31.439: %LINK-3-UPDOWN: Interface Serial0/1/0:0, changed state to up
*Mar 8 02:23:32.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:0, changed state to up
*Mar 8 02:23:34.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to down (RAI detected)
*Mar 8 02:23:36.439: %LINK-3-UPDOWN: Interface Serial0/1/0:0, changed state to down
*Mar 8 02:23:37.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:0, changed state to down
*Mar 8 02:23:37.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to up
*Mar 8 02:23:39.439: %LINK-3-UPDOWN: Interface Serial0/1/0:0, changed state to up
*Mar 8 02:23:40.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:0, changed state to up
*Mar 8 02:23:40.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to down (RAI detected)
*Mar 8 02:23:42.439: %LINK-3-UPDOWN: Interface Serial0/1/0:0, changed state to down
*Mar 8 02:23:42.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to up
*Mar 8 02:23:44.439: %LINK-3-UPDOWN: Interface Serial0/1/0:0, changed state to up
*Mar 8 02:23:44.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to down (RAI detected)
*Mar 8 02:23:46.439: %LINK-3-UPDOWN: Interface Serial0/1/0:0, changed state to down
*Mar 8 02:23:46.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to up
*Mar 8 02:23:48.439: %LINK-3-UPDOWN: Interface Serial0/1/0:0, changed state to up
*Mar 8 02:23:50.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to down (RAI detected)
*Mar 8 02:23:51.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to up
*Mar 8 02:23:53.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to down (RAI detected)
*Mar 8 02:23:54.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to up
*Mar 8 02:23:57.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to down (RAI detected)
*Mar 8 02:23:58.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to up
*Mar 8 02:24:00.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to down (RAI detected)
*Mar 8 02:24:02.439: %LINK-3-UPDOWN: Interface Serial0/1/0:0, changed state to down
*Mar 8 02:24:03.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:0, changed state to down
*Mar 8 02:24:04.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to up
*Mar 8 02:24:05.439: %LINK-3-UPDOWN: Interface Serial0/1/0:0, changed state to up
*Mar 8 02:24:06.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:0, changed state to up
*Mar 8 02:24:09.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to down (RAI detected)
*Mar 8 02:24:10.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to up
*Mar 8 02:24:12.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to down (RAI detected)
*Mar 8 02:24:14.439: %LINK-3-UPDOWN: Interface Serial0/1/0:0, changed state to down
*Mar 8 02:24:15.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:0, changed state to down
*Mar 8 02:24:15.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to up
*Mar 8 02:24:16.439: %LINK-3-UPDOWN: Interface Serial0/1/0:0, changed state to up
*Mar 8 02:24:17.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0:0, changed state to up
*Mar 8 02:24:19.439: %CONTROLLER-5-UPDOWN: Controller T1 0/1/0, changed state to down (RAI detected)

atippett

A better question is why are you setting up frame-relay in your home lab? That's not in the CCNA objectives anymore.

binatical

CCNP Collab, figured I'd post it here because this is where R&S is...

DCD

Check the settings at the remote end and verify that they match your port settings. Also check your cable.

clarson

have to tried replacing the cable with know good one?

binatical

It was the cable, thanks!