CCNA R&S / CCNA Voice / CCNA Security

sam88

Hi Everyone,


I would like to thank everyone and Special thanks to Mr. Clarson for all his support and time. I'm starting my carrier in networking field.


Now, I need help in setting up a voice Home lab and other course that I can use with these equipment. I'm sharing the device that I have with me . I need guidance regarding the missing part/modules/suggestions and topology.


Routers
********


1- 1760 [1FE] [96/32]
(IOS- c1700-entbasek9-mz.124-25a.bin )


Cisco 1760 (MPC860P) processor (revision 0x400) with 85627K/12677K bytes of memory.
Processor board ID FOC07271KE2 (2250070842), with hardware revision 0000
MPC860P processor: part number 5, mask 2
1 FastEthernet interface
1 ISDN Basic Rate interface
32K bytes of NVRAM.
32768K bytes of processor board System flash (Read/Write)


2- 2620XM [1FE] [64/16 CF]
(IOS- c2600-d-mz.122-13c.bin)


cisco 2620XM (MPC860P) processor (revision 0x100) with 61440K/4096K bytes of memory.
Processor board ID
M860 processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)


3- 2620XM [1FE] [96/16 CF]
(IOS- c2600-d-mz.122-29a.bin)


cisco 2620XM (MPC860P) processor (revision 0x100) with 94208K/4096K bytes of memory.
Processor board ID
M860 processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
1 ISDN Basic Rate interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)




4- 1841 [2FE] [256/64 CF]
(IOS- c2800nm-adventerprisek9-mz.151-4.M12a.bin)


Cisco 1841 with 239616K/22528K bytes of memory.
Processor board ID
2 FastEthernet interfaces
2 Channelized (E1 or T1)/PRI ports
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
62720K bytes of ATA CompactFlash (Read/Write)
(IOS- c1841-adventerprisek9-mz.151-4.M12a.bin)


5- 1841 [2FE] [256/64 CF]
(IOS- c1841-adventerprisek9-mz.151-4.M12a.bin)


Cisco 1841 with 237568K/24576K bytes of memory.
Processor board ID
2 FastEthernet interfaces
2 Virtual Private Network (VPN) Modules
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
62720K bytes of ATA CompactFlash (Read/Write)


6- 2811 [2FE] [256/128 CF]
(IOS- c2800nm-adventerprisek9-mz.151-4.M12a.bin)


7- 2821 [2GE] [512+512 / 128] (Not sure whether 1 512mb ram is working on this router)
(IOS- c2800nm-adventerprisek9-mz.151-4.M12a.bin)


Switches
********
1- 2950-24PT
(IOS- c2950-i6q4l2-mz.121-19.EA1c.bin )


cisco WS-C2950T-24 (RC32300) processor (revision P0) with 20808K bytes of memory.
Processor board ID
Last reset from system-reset
Running Enhanced Image
24 FastEthernet/IEEE 802.3 interface(s)
2 Gigabit Ethernet/IEEE 802.3 interface(s)


2- 2950-24PT
(IOS- )


3- 2950-24PT
(IOS- )


4- 3550-24PT [NON-PoE]
(IOS- c3550-i9q3l2-mz.121-22.EA7/c3550-i9q3l2-mz.121-22.EA7.bin)


5- 3550-24PT
(IOS- )


Ip Phones(SCCP)
**************
Stuck in boot Loop (power cube used)
1- 7942
2- 7942
3- 7942


Modules
*******
1- VWIC2-2MFT T1/E1
2- VWIC2-2MFT T1/E1
3- VWIC2-1MFT T1/E1
4- WIC-2T
5- WIC-2T
6- 1 ISDN Basic Rate interface
7- 1 ISDN Basic Rate interface
8-
9-
10-


CARDS
******
1- PVDM-256K-4
2- PVDM-256K-4
3- PVDM2-16 DSP
4- PVDM2-16 DSP
5-
6-
7-
8-




CABLES
*******
1- Back to Back smart serial cable or DB60 DTE/DCE
2- Back to Back smart serial cable or DB60 DTE/DCE
3- Console Cable
4- Console Cable
5- Console Cable
6-
7-
8-
LAPTOP
*******
1-DELL INSPIRON WIN7-64bit I3-3217U 1.80GHz


> VMware Workstation 12 Player
[Winserver 2012 R2 (Data centre)
CUCM 9 installed]




ACCESSORIES
************
1- CRIMPING TOOL
2- CABLE TESTER
3-
4-
5-

For Security I believe I have to purchase ASA5510.