Problem with 2521

kafifi13

Guys,

I bought a 2521 off ebay to eventually use as my Frame Relay switch. I booted it up and this is what iv'e got. Doesn't go any further than this. Any ideas of what the problem might be and how i can fix it?

System Bootstrap, Version 11.0(10c), SOFTWARE












Router con0 is now available

H
Copyright (c) 1986-1996 by cisco SystemsN to get started.
2500 processor with 6144 Kbytes of main memoryer#show ip route
% No connec
Codes: C

%SYS-4-CONFIG_NEWER: Configurations from version 11.1 may not be correctly under
% Incomplete command.s list entrygoyal
D - EIGRP, EX - EIG
stood.rnal,
F3: 5702080+171780+244320 at 0x3000060
show mac-address-table Netw

Restricted Rights LegendNSSA external type 1, N2 - OSPF NSSA e

Use, duplication, or disclosure by the Government is
show sessionsalias
E1 - OSPF exter
Bridging software.
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.#######################
speed 100
spanning-tre
Basic Rate ISDN software, Version 1.0.
###############################
1 Token Ring/IEEE 802.5 interface.##############
descripti
2 Serial network interfaces.t
duplex fullc,
2 Low-speed serial(sync/async) network interfaces.#################################
interf
1 ISDN Basic Rate interface.0/3an interface to configure
32K bytes of non-volatile config
!t
interface FastEth
2500 processor with 6144 Kbytes of main memory##############################################

%SYS-4-CONFIG_NEWER: Configurations from version 11.1 may not be correctly under

#######################################################
stood.######
F3: 5702080+171780+244320 at 0x3000060
dupl

Restricted Rights Legend Restricted Rights Legend
170 West Tasman Drive
San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) 3000 Software (IGS-DR-L), Version 11.1(6), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1996 by cisco Systems, Inc.
Compiled Mon 09-Sep-96 14:16 by tej
Image text-base: 0x0302F9C8, data-base: 0x00001000

cisco 2521 (68030) processor (revision K) with 6144K/2048K bytes of memory.
Processor board ID 05617431, with hardware revision 00000002
Bridging software.
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
Basic Rate ISDN software, Version 1.0.
1 Token Ring/IEEE 802.5 interface.
2 Serial network interfaces.
2 Low-speed serial(sync/async) network interfaces.
1 ISDN Basic Rate interface.
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash partition 1 (Read ONLY)
8192K bytes of processor board System flash partition 2 (Read/Write)

mikej412

To rule out the exiting configuration, bypass the startup config by setting the config register to 0x2142 (like in password recovery).

Also double check your console cable is firmly attached and that you have the proper configuration (N-8-1 No Flow Control) in your terminal software.

keenon

erase the start up config

i have a router with this same error "F3: 5702080+171780+244320 at 0x3000060" it still worked fine

there is a thread here on reformatting the partition back into 1 16mb piece versus 2 8mb or you can do a google or cisco site search on the topic

kafifi13

Excellent. Thanks guys...i just needed a point in the right direction.

kafifi13

I'm all set. Thanks guys. The config register was all screwed up. Got it straighted out by doing the break sequence and changing it to 2102.