WIC Card Error
357
Member Posts: 47 ■■□□□□□□□□
in CCNA & CCENT
Hi!
Could you please help me on my WIC-2T card that I got from one of the vendor?
I tried to install on different WIC slot but still got the same error message. Here's the error message during booting:
Press RETURN to get started!
00:00:07: %QUICC-1-UNKNOWN_WIC: Quicc(0), wic card has an unknown id of 12
00:00:09: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
00:00:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed s
tate to down
00:00:28: %LINK-5-CHANGED: Interface BRI0/0, changed state to administratively d
own
00:00:28: %IP-5-WEBINST_KILL: Terminating DNS process
00:00:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0, changed state
to down
00:00:30: %LINK-5-CHANGED: Interface Ethernet0/0, changed state to administrativ
ely down
00:00:39: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-I-M), Version 12.2(46), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Thu 26-Apr-07 18:06 by pwade
00:00:39: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold star
t
Router>
Your reply is very much appreciated.
Best regards
Could you please help me on my WIC-2T card that I got from one of the vendor?
I tried to install on different WIC slot but still got the same error message. Here's the error message during booting:
Press RETURN to get started!
00:00:07: %QUICC-1-UNKNOWN_WIC: Quicc(0), wic card has an unknown id of 12
00:00:09: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
00:00:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed s
tate to down
00:00:28: %LINK-5-CHANGED: Interface BRI0/0, changed state to administratively d
own
00:00:28: %IP-5-WEBINST_KILL: Terminating DNS process
00:00:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0, changed state
to down
00:00:30: %LINK-5-CHANGED: Interface Ethernet0/0, changed state to administrativ
ely down
00:00:39: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-I-M), Version 12.2(46), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Thu 26-Apr-07 18:06 by pwade
00:00:39: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold star
t
Router>
Your reply is very much appreciated.
Best regards
Comments
-
keenon
Member Posts: 1,922 ■■■■□□□□□□
the version of code doesn't recognize the card.. i suggest looking up the card on cisco's site and seeing which code version is required to support the card on your specific routerBecome the stainless steel sharp knife in a drawer full of rusty spoons -
r_durant
Member Posts: 486 ■■■□□□□□□□
Error Message
%QUICC-1-UNKNOWN_WIC: Quicc([dec]), wic card has an unknown id of [hex]
Explanation The software does not recognize the type of WIC card plugged into the port module.
Recommended Action Check the part number on the WIC card to verify that it is supported in the Cisco IOS release operational on the router or contact your technical support representative.
Yea, what keenon said...CCNA (Expired...), MCSE, CWNA, BSc Computer Science
Working on renewing CCNA! -
mgeorge
Member Posts: 774 ■■■□□□□□□□
Do a "sh ver" for me and post the dispatch.
mgThere is no place like 127.0.0.1 -
357
Member Posts: 47 ■■□□□□□□□□
Hi!
Thank you very much for all your replies.
The problem was compatibility. I got the info from cisco site.
Here it is:
"The NM-1E2W, NM-1E1R2W, and NM-2E2W Network Modules do not have enough
performance power to support the WIC-2T due to hardware limitations."
Link:
http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note0
9186
a00800b0858.shtml
Thanks again.
Regards all