Remote Access to my LAB

elegua

Hi.

I finished the configuration of my access server in my home lab and i neet to know if it works, here is the info:

username: cisco
password: cisco
ip: 206.53.50.230

Can you guys access using SSH v2 and let me know if it's working?.

Thanks.

srg

Yup, seems to work :]

Silver Bullet

AccessServer#sho int
Ethernet0/0 is up, line protocol is up
  Hardware is AmdP2, address is 0002.4b72.6440 (bia 0002.4b72.6440)
  Description: TO GATEWAY
  Internet address is 192.168.200.2/24
  MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output 00:00:00, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 3000 bits/sec, 5 packets/sec
  5 minute output rate 8000 bits/sec, 8 packets/sec
     2726 packets input, 209561 bytes, 0 no buffer
     Received 1 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     4913 packets output, 567383 bytes, 0 underruns
     0 output errors, 6 collisions, 1 interface resets
     0 babbles, 0 late collision, 18 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
Loopback0 is up, line protocol is up
  Hardware is Loopback
  Internet address is 10.1.1.1/8
  MTU 1514 bytes, BW 8000000 Kbit, DLY 5000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation LOOPBACK, loopback not set
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/0 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
AccessServer#

Now what was that command you wanted me to run.......ERASE FLASH?

Netstudent

that would be so wrong.

elegua

Silver Bullet wrote:

AccessServer#sho int
Ethernet0/0 is up, line protocol is up
  Hardware is AmdP2, address is 0002.4b72.6440 (bia 0002.4b72.6440)
  Description: TO GATEWAY
  Internet address is 192.168.200.2/24
  MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output 00:00:00, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 3000 bits/sec, 5 packets/sec
  5 minute output rate 8000 bits/sec, 8 packets/sec
     2726 packets input, 209561 bytes, 0 no buffer
     Received 1 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     4913 packets output, 567383 bytes, 0 underruns
     0 output errors, 6 collisions, 1 interface resets
     0 babbles, 0 late collision, 18 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
Loopback0 is up, line protocol is up
  Hardware is Loopback
  Internet address is 10.1.1.1/8
  MTU 1514 bytes, BW 8000000 Kbit, DLY 5000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation LOOPBACK, loopback not set
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/0 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
AccessServer#

Now what was that command you wanted me to run.......ERASE FLASH?

Try and let me know.

Netstudent

elegua,

How did you set yours up? Also is that 206.53.50.230 the 1 IP that your service provider gave you or did you request more public IP's?

elegua

Netstudent wrote:

elegua,

How did you set yours up? Also is that 206.53.50.230 the 1 IP that your service provider gave you or did you request more public IP's?

Hi Netstudent,

I have a 8 static IP's Block and took one for remote access to my access server, i have ADSL 6.0 at home, i'm using a 1760 router with one ADSL wic card for my internet service, here is a pic, R-A is the 1760 (Gateway) and R-B is the access server (2610 with NM-32A).

elegua

Hi Guys,

Thanks guys for your replay, later on when i finished some configurations i'll let you get in to my lab with more privilege and do some frame relay or routing lab.


Thanks.