just started getting this error message on 2600 router

aueddonlineaueddonline Member Posts: 611 ■■□□□□□□□□
in CCNA & CCENT
I did a write erase then a reload and my router has started producing this message


*Mar 1 00:14:49.417: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/cisconet.cfg) failed



any ideas
What's another word for Thesaurus?
· Share on FacebookShare on Twitter

Comments

  • NetstudentNetstudent Member Posts: 1,693 ■■■□□□□□□□
    try the boot system flash command. It looks as if it is trying to boot from a tftp. Also make sure your register is at 2102.
    There is no place like 127.0.0.1 BUT 209.62.5.3 is my 127.0.0.1 away from 127.0.0.1!
    · Share on FacebookShare on Twitter
  • networker050184networker050184 Mod Posts: 11,962 Mod
    Try the no service config command. It looks like your router id trying to autoload the config.
    An expert is a man who has made all the mistakes which can be made.
    · Share on FacebookShare on Twitter
  • aueddonlineaueddonline Member Posts: 611 ■■□□□□□□□□
    tried the no service config (global) command, still getting the same error


    %Error opening tftp://255.255.255.255/ciscortr.cfg (Timed out)
    *Mar 1 00:07:07.348: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/ciscortr.cfg) failed
    What's another word for Thesaurus?
    · Share on FacebookShare on Twitter
  • aueddonlineaueddonline Member Posts: 611 ■■□□□□□□□□
    I checked the register, looks fine

    IOS (tm) C2600 Software (C2600-IO3-M), Version 12.3(3), RELEASE SOFTWARE (fc2)
    Copyright (c) 1986-2003 by cisco Systems, Inc.
    Compiled Tue 19-Aug-03 16:32 by dchih
    Image text-base: 0x80008098, data-base: 0x80D11A24

    ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

    Router uptime is 9 minutes
    System returned to ROM by power-on
    System image file is "flash:c2600-io3-mz.123-3.bin"

    cisco 2610 (MPC860) processor (revision 0x203) with 28672K/4096K bytes of memory.
    Processor board ID JAD0540005B (635500995)
    M860 processor: part number 0, mask 49
    Bridging software.
    X.25 software, Version 3.0.0.
    1 Ethernet/IEEE 802.3 interface(s)
    1 Serial network interface(s)
    32K bytes of non-volatile configuration memory.
    8192K bytes of processor board System flash (Read/Write)

    Configuration register is 0x2102
    What's another word for Thesaurus?
    · Share on FacebookShare on Twitter
  • aueddonlineaueddonline Member Posts: 611 ■■□□□□□□□□
    is there a boot command I can use?
    What's another word for Thesaurus?
    · Share on FacebookShare on Twitter
  • networker050184networker050184 Mod Posts: 11,962 Mod
    Did you reload the router after issuing the no service config command???
    An expert is a man who has made all the mistakes which can be made.
    · Share on FacebookShare on Twitter
  • aueddonlineaueddonline Member Posts: 611 ■■□□□□□□□□
    problem solved

    when i was copying the show ver I by mistake pated it back into the command line, and the problem has gone, not sure if those events are related but it's sorted it
    What's another word for Thesaurus?
    · Share on FacebookShare on Twitter
  • aueddonlineaueddonline Member Posts: 611 ■■□□□□□□□□
    I since reloaded the router and the problem has gone,
    What's another word for Thesaurus?
    · Share on FacebookShare on Twitter
  • networker050184networker050184 Mod Posts: 11,962 Mod
    Hmmmmm I don't think they are related, but at least your issue is fixed!
    An expert is a man who has made all the mistakes which can be made.
    · Share on FacebookShare on Twitter
  • aueddonlineaueddonline Member Posts: 611 ■■□□□□□□□□
    no i think your right, could have been that, must ahve been that command, cheers guys

    no service config - what's the command do, stop all serivces the router is trying to access?
    What's another word for Thesaurus?
    · Share on FacebookShare on Twitter
  • rossonieri#1rossonieri#1 Member Posts: 799 ■■■□□□□□□□
    aueddonline wrote:
    I did a write erase then a reload and my router has started producing this message


    *Mar 1 00:14:49.417: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/cisconet.cfg) failed



    any ideas

    that is because you tried to start autoconfiguration after write/erase initialization

    just answer no when prompted.

    HTH.
    the More I know, that is more and More I dont know.
    · Share on FacebookShare on Twitter
  • networker050184networker050184 Mod Posts: 11,962 Mod
    no service config - what's the command do, stop all serivces the router is trying to access?

    The service config command is used when you are auto loading the configuration from a remote server. You would also specify what the file name and location is.
    An expert is a man who has made all the mistakes which can be made.
    · Share on FacebookShare on Twitter
  • giankanagiankana Registered Users Posts: 1 ■□□□□□□□□□
    type a command sh flash, and configure boot option with a command boot system flash:<ios>
    · Share on FacebookShare on Twitter
Sign In or Register to comment.