router 2600 problem

aueddonline

i'm using htis 2600 as a frame-relay switch, was using it yesterday fine, turned it on today and it goes though this process over and over again, any ideas?

System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2600 platform with 32768 Kbytes of main memory

program load complete, entry point: 0x80008000, size: 0x768468
Self decompressing the image : #################################################################################################################################### [OK]

Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
000091 0X0008B800 C2600 single Ethernet
000025 0X00033480 Eight port Async/Sync
0X000F3BB0 public buffer pools
0X00211000 public particle pools
TOTAL: 0X003C3830

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 4Mb.
Using 12 percent iomem. [4Mb/32Mb]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IO3-M), Version 12.3(3), RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Tue 19-Aug-03 16:32 by dchih
Image text-base: 0x80008098, data-base: 0x80D11A24



Unexpected exception to CPUvector 100, PC = 804FFCE4
-Traceback= 804FFCE4 8050DD50 8050D530 80028C94 80028D5C 800254E8 8050AEE0 8050AFC4 8048B6E8 803A8BB0 803A8DA4 80492A2C 80495FC8
Free space check for flash:crashinfo_19930301-000006 failed (288/491)

Queued messages:
*** System received a SegV exception ***
signal= 0xb, code= 0x100, context= 0x814d3aa8
PC = 0x804ffce4, Vector = 0x100, SP = 0x815531b8

networker050184

Did you put any new modules in it? I have seen an error like that when putting new modules in a 2600. If so try to remove them and then power it back up.

aueddonline

haven't changed it, it had a serial A/S 8 in there for a while, could try it without

aueddonline

ok i've done that and it's loading up now, does that mean i'll have to put the 8 serial interface into another router and how come it's only decided to have a problem with it today?

networker050184

Make sure the module is supported by your current model/IOS. It might be a bad module as well. If it is supported you can try it in another router to be sure.

aueddonline

well that's the thing i've been using that module in that router for a couple weeks now.

dtlokee

I would reinstall the IOS from a tftp server then see what happens, the error seems to be a hardware error (system board) also make sure there's nothing floating around inside the chassis, I have see those copper clips fall off the NM slot covers and NM's themselves and short things out and cause all kinds of errors. I have seen similar problems before (router just stops working for no apparent reason) and the bad news is the routers/switches were usually found to be counterfeit.

determinedgerman

Looks like a IOS issue......here is what Cisco output Interpreter is coming up with:


ROUTER CONSOLE MESSAGE NOTIFICATIONS (if any)

ERROR: 'Segmentation Violation (SegV) Exceptions' are always related to software
issues.
TRY THIS: Please refer to the TAC Case Collection - SegV exceptions for troubleshooting.
REFERENCE: For more information, see SegV Exceptions.

REFERENCE: For more information, see:
Troubleshooting Router Crashes
Less Common Types of System Crashes

Here are some related bug id's:

CSCdz74155
CSCdk47797
CSCds84936
CSCdw55259
CSCei19391
CSCsa70069


For more information you might want to check the crashfile.

Hope this helps!

Mike

RobertJohn

I bought a router on Marktplaats(Dutch), I have the same problem.
I an new to Cisco , I want to start learning the basic commands.
What can I do to try to repair the router, can someone help, please.

greets, Rob