IOS upgrade on 3550

i've just copied th image c3550-ipservices-mz.122-25.SEC.bin using TFTP to my switch and I can see it on there but when I reload the show ver below is still showing the old image? what am I doing wrong?

2C-3550#show flash

Directory of flash:/

2 -rwx 0 Jan 01 1970 00:01:21 env_vars
3 -rwx 342 Jan 01 1970 00:01:21 system_env_vars
4 -rwx 796 Mar 01 1993 00:04:18 vlan.dat
6 -rwx 6196885 Mar 01 1993 00:06:25 c3550-ipservices-mz.122-25.SEC.bin
7 -rwx 1970 Mar 01 1993 02:24:07 config.text
9 drwx 192 Mar 01 1993 00:03:52 c3550-i5q3l2-mz.121-9.EA1c

2C-3550#show ver
Cisco Internetwork Operating System Software
IOS (tm) C3550 Software (C3550-I5Q3L2-M), Version 12.1(9)EA1c, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Tue 28-May-02 10:31 by antonino
Image text-base: 0x00003000, data-base: 0x00685778

ROM: Bootstrap program is C3550 boot loader

2C-3550 uptime is 6 minutes
System returned to ROM by power-on
System image file is "flash:c3550-i5q3l2-mz.121-9.EA1c/c3550-i5q3l2-mz.121-9.EA1c.bin"

cisco WS-C3550-24 (PowerPC) processor (revision E0) with 65526K/8192K bytes of memory.
Processor board ID CHK0633V1Z0
Last reset from warm-reset
Bridging software.
Running Layer2/3 Switching Image

Ethernet-controller 1 has 12 Fast Ethernet/IEEE 802.3 interfaces

Ethernet-controller 2 has 12 Fast Ethernet/IEEE 802.3 interfaces

Ethernet-controller 3 has 1 Gigabit Ethernet/IEEE 802.3 interface

Ethernet-controller 4 has 1 Gigabit Ethernet/IEEE 802.3 interface

24 FastEthernet/IEEE 802.3 interface(s)
2 Gigabit Ethernet/IEEE 802.3 interface(s)

The password-recovery mechanism is enabled.
384K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:0A:B7:86:6A:00
Motherboard assembly number: 73-5700-08
Power supply part number: 34-0966-02
Motherboard serial number: CAT063303EN
Power supply serial number: DCA06320M20
Model revision number: E0
Motherboard revision number: D0
Model number: WS-C3550-24-EMI
System serial number: CHK0633V1Z0
Configuration register is 0x10F

Find more posts tagged with

Free for TechExams community: Cybersecurity salary guide

Compare cert salaries and plan your next career move

Button

Comments

networker050184

Did you tell the switch to boot from the new image?

aueddonline

networker050184 wrote:

Did you tell the switch to boot from the new image?

no, how do i do that?

networker050184

boot system flash filename(the new one)

then reload the switch.

aueddonline

networker050184 wrote:

boot system flash filename(the new one)

then reload the switch.

perfect, that's the first time i've had to do that after loading an image, but that's cool now that switch can do all the same tricks as the other one. That older image didn't even have LACP

networker050184

You don't have to use the command if you erase the old image first. If you have two images on there you need to specify which one to boot from.