Question about network statement in EIGRP

In the ultimate CCNA study package under the EIGRP section Brain says that EIGRP uses wildmask
in their network statements NOT subnet masks. I've tried using a subnet mask and it worked fine.
Did he mean by using a wildcard you can be more specific with your network statement?

Find more posts tagged with

Free for TechExams community: Cybersecurity salary guide

Compare cert salaries and plan your next career move

Button

Comments

gojericho0

with the wild card mask you can specify a range of interface ips that you want to run the EIGRP process

shednik

To go along with what gojericho0 said you use the wildcard mask to specify the range of ips that will advertise on the router. so you can type in 192.168.1.0 0.0.0.255 that will allow any interface in that range to advertise eigrp. if you had typed 255.255.255.0 the router will take it, and after re-reading some things I see this method will work as well, but when looking in the running configuration it will be displayed on the wildcard mask format of 0.0.0.255.

tech-airman

kadshah wrote:

In the ultimate CCNA study package under the EIGRP section Brain says that EIGRP uses wildmask
in their network statements NOT subnet masks. I've tried using a subnet mask and it worked fine.
Did he mean by using a wildcard you can be more specific with your network statement?

Disclaimer: I have never heard of the "...ultimate CCNA study package..." so it's highly unlikely I'd know the exact wording used in that material.

kadshah,

For EIGRP, there are at least three ways to specify the network statement:

network x.x.x.x
network x.x.x.x s.s.s.s
network x.x.x.x w.w.w.w

where:
x.x.x.x is the IP address for the network
s.s.s.s is the subnet mask
w.w.w.w is the wildcard mask

dynamik

tech-airman wrote:

Disclaimer: I have never heard of the "...ultimate CCNA study package..." so it's highly unlikely I'd know the exact wording used in that material.

www.thebryantadvantage.com

The website is painful, but the information is good.

It's Chris Bryant's package. He also does the Train Signal CBTs.

Edit: Looks like he now has a CCNA: Security package as well!

networker050184

It is not a subnet mask it is a wildcard mask. A 0 match 1 no match. So 10.0.0.1 0.0.0.255 would match 10.0.0.0-255. If you used 10.0.0.1 255.0.0.0 would match 1-255.0.0.0.1.

shednik

I wanted to test this and it does work in that format..

lab(config)#router eigrp 101
lab(config-router)#network 10.10.0.0 255.255.0.0
lab(config-router)#exit

lab#sh run

router eigrp 101
network 10.10.0.0 0.0.255.255
auto-summary
no eigrp log-neighbor-changes

networker050184

I was just about to edit my post as I tried it too. I guess you learn something new everyday!

kadshah

I've tested both either works fine. Chris used the word NOT which led me to believe that you couldn't use a subnet mask until I tried it on my lab. Richard Deal's CCNA book says that a subnet mask could be used he doesn't even mention wildcard as being an option.

networker050184

The subnet mask option was added in 12.0 (4)T so a lot of people that have been around for a long time are probably not very familiar with it. I didn't find out about it until today myself.

shednik

networker050184 wrote:

The subnet mask option was added in 12.0 (4)T so a lot of people that have been around for a long time are probably not very familiar with it. I didn't find out about it until today myself.

Even if you haven't been around long like myself I didn't know about it until I tried it