Interfaces not detected after IOS upgrade
yanks4everontop
Member Posts: 106
in CCNA & CCENT
After updating my IOS now my NM-2E2W and WIC-1T is not being detected. The weird thing is I have two 3640's, now both running the same IOS version and both have the exact same interfaces. One boots fine. The one that doesn't boot, I get the following output:
*Mar 1 00:00:11.131: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to upBad
Hardware in bay/slot/sub_slot = 1/-1/-1
*Mar 1 00:00:17.291: %PA-3-NOTSUPPORTED: PA in slot1 (Unknown (type 0)) is not supported on this image.
Please issue "show diag" in fully loaded IOS image
to get the PA's information and verify if it is supported
by this image, a newer version may be needed.
*Mar 1 00:00:17.291: %LINK-4-NOMAC: A random default MAC address of 0000.0c11.0674 has
been chosen. Ensure that this address is unique, or specify MAC
addresses for commands (such as 'novell routing') that allow the
use of this address as a default.sslinit fn
*Mar 1 00:00:25.483: %SYS-3-HARIKARI: Process CCSIP_UDP_SOCKET top-level routine exited
*Mar 1 00:00:25.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface , changed state to up
*Mar 1 00:14:31.723: %SYS-5-RESTART: System restarted --
Cisco IOS Software, 3600 Software (C
Router>3640-JK9O3S-M), Version 12.4(1a), RELEASE SOFTWARE (fc2)
Technical Support: Cisco - Shortcut
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Fri 27-May-05 16:29 by hqluong
*Mar 1 00:14:31.727: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
*Mar 1 00:14:31.755: %SYS-3-HARIKARI: Process CCH323_CT top-level routine exited
*Mar 1 00:00:11.131: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to upBad
Hardware in bay/slot/sub_slot = 1/-1/-1
*Mar 1 00:00:17.291: %PA-3-NOTSUPPORTED: PA in slot1 (Unknown (type 0)) is not supported on this image.
Please issue "show diag" in fully loaded IOS image
to get the PA's information and verify if it is supported
by this image, a newer version may be needed.
*Mar 1 00:00:17.291: %LINK-4-NOMAC: A random default MAC address of 0000.0c11.0674 has
been chosen. Ensure that this address is unique, or specify MAC
addresses for commands (such as 'novell routing') that allow the
use of this address as a default.sslinit fn
*Mar 1 00:00:25.483: %SYS-3-HARIKARI: Process CCSIP_UDP_SOCKET top-level routine exited
*Mar 1 00:00:25.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface , changed state to up
*Mar 1 00:14:31.723: %SYS-5-RESTART: System restarted --
Cisco IOS Software, 3600 Software (C
Router>3640-JK9O3S-M), Version 12.4(1a), RELEASE SOFTWARE (fc2)
Technical Support: Cisco - Shortcut
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Fri 27-May-05 16:29 by hqluong
*Mar 1 00:14:31.727: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
*Mar 1 00:14:31.755: %SYS-3-HARIKARI: Process CCH323_CT top-level routine exited
Comments
-
mikej412
Member Posts: 10,086 ■■■■■■■■■■
Are you sure the Network Module is firmly seated?
Are you sure the WIC is firmly seated in the NM?
Did you try booting without the WIC-1T?
Did you try booting without the NM?
Did you try the NM in another slot?
Did you try the WIC in another slot?:mike: Cisco Certifications -- Collect the Entire Set! -
yanks4everontop
Member Posts: 106
I guess I'll try reseating but I haven't touched anything since the last few times I worked on it so I don't see how anything could have gotten unseated.
Well reseating in the same NM slot didn't work but moving it to a different slot did. Don't really understand it but at least it's working, for now. Thanks Mike.