Help !!!! LAN Connection in packet tracer with 2 router

lebronlebron ■□□□□□□□□□ Posts: 2Member ■□□□□□□□□□
I just started my CCNA 1 course and this comes from my assessment and I am really stuck in it need some help for connecting two LAN with 2 routers

Given Network = 172.93.0.0/16
LAN 1 =1000 hosts
LAN 2 = 500 hosts
WAN = 2 ( i.e Routers )

so I subnet the given network in to 3 subnets (VLSM)

LAN 1:
network : 172.93.0.0/22
host range :172.93.0.1-172.93.3.254
board cast: 172.93.3.255

LAN 2:
Network :172.93.4.0/23
host range : 172.93.4.1-172.93.5.254
boardcast : 172.93.5.255

WAN :
network : 172.93.6.0/30
host range : 172.93.6.1-172.93.6.2
board cast : 172.93.6.3

then I assigned IP addresses to LAN 1 in PAcket Tracer 5.1

PC 0 ip :172.93.0.1
MAsk : 255.255.252.0
gateway :172.93.0.1

PC 1 IP:172.93.0.2
MAsk : 255.255.252.0
gateway :172.93.0.1

LAN 2
PC 3 IP :172.93.4.1
Mask : 255.255.254.0
gateway: 172.93.4.1

PC 4 IP : 172.93.4.2
Mask : 255.255.254.0
gateway: 172.93.4.1


router A
f0/0 : 172.93.3.254 255.255.252.0
s0/0 : 172.93.6.1 255.255.255.252

router B
f0/0 : 172.93.5.254 255.255.254.0
s0/0 : 172.93.6.2 255.255.255.252

ROuter Config : Router A

config t
int f0/0
ip add 172.93.3.254 255.255.252.0
no shut
int s0/0
ip add 172.93.6.1 255.255.255.252
no shut
clock rate 6400
router rip
ver 2
network 172.93.3.254
network 172.93.6.1
end
exit

And did almost similar with router B
I assigned all my ip add and router configs in my packet tracer

And In my packet tracer all my network start glowing with green light but couldnt ping PC from LAN1 to PC LAN 2 though 2 routers are connected and ping each other.

here is my packet tracer file :
4shared.com - online file sharing and storage - download Networking.pkt


Please help me OUT !!!
thanks in advance

Comments

  • Bl8ckr0uterBl8ckr0uter ■■■■■■■■□□ Posts: 5,031Inactive Imported Users ■■■■■■■■□□
    lebron wrote: »
    I just started my CCNA 1 course and this comes from my assessment and I am really stuck in it need some help for connecting two LAN with 2 routers

    Given Network = 172.93.0.0/16
    LAN 1 =1000 hosts
    LAN 2 = 500 hosts
    WAN = 2 ( i.e Routers )

    so I subnet the given network in to 3 subnets (VLSM)

    LAN 1:
    network : 172.93.0.0/22
    host range :172.93.0.1-172.93.3.254
    board cast: 172.93.3.255

    LAN 2:
    Network :172.93.4.0/23
    host range : 172.93.4.1-172.93.5.254
    boardcast : 172.93.5.255

    WAN :
    network : 172.93.6.0/30
    host range : 172.93.6.1-172.93.6.2
    board cast : 172.93.6.3

    then I assigned IP addresses to LAN 1 in PAcket Tracer 5.1

    PC 0 ip :172.93.0.1
    MAsk : 255.255.252.0
    gateway :172.93.0.1

    PC 1 IP:172.93.0.2
    MAsk : 255.255.252.0
    gateway :172.93.0.1

    LAN 2
    PC 3 IP :172.93.4.1
    Mask : 255.255.254.0
    gateway: 172.93.4.1

    PC 4 IP : 172.93.4.2
    Mask : 255.255.254.0
    gateway: 172.93.4.1


    router A
    f0/0 : 172.93.3.254 255.255.252.0
    s0/0 : 172.93.6.1 255.255.255.252

    router B
    f0/0 : 172.93.5.254 255.255.254.0
    s0/0 : 172.93.6.2 255.255.255.252

    ROuter Config : Router A

    config t
    int f0/0
    ip add 172.93.3.254 255.255.252.0
    no shut
    int s0/0
    ip add 172.93.6.1 255.255.255.252
    no shut
    clock rate 6400
    router rip
    ver 2
    network 172.93.3.254
    network 172.93.6.1
    end
    exit

    And did almost similar with router B
    I assigned all my ip add and router configs in my packet tracer

    And In my packet tracer all my network start glowing with green light but couldnt ping PC from LAN1 to PC LAN 2 though 2 routers are connected and ping each other.

    here is my packet tracer file :
    4shared.com - online file sharing and storage - download Networking.pkt


    Please help me OUT !!!
    thanks in advance

    I never saw a rip statement for the .4 network. Can you post the output from your routing tables?
  • billscott92787billscott92787 Posts: 933Member
    I agree I don't see the RIP statement for the .4 network. Can you post the packet tracer file, so I can take a look, or PM it to me.
  • stlsmoorestlsmoore ■■■□□□□□□□ Posts: 515Member ■■■□□□□□□□
    Why are your LAN PC Gateway addresses pointing to PC 0 in LAN 1 and PC 3 in LAN 2? Also for your RIP statements I would do a network command on the subnet not the the Routers LAN interface.
    My Cisco Blog Adventure: http://shawnmoorecisco.blogspot.com/

    Don't Forget to Add me on LinkedIn!
    https://www.linkedin.com/in/shawnrmoore
  • lebronlebron ■□□□□□□□□□ Posts: 2Member ■□□□□□□□□□
    stlsmoore wrote: »
    Why are your LAN PC Gateway addresses pointing to PC 0 in LAN 1 and PC 3 in LAN 2? Also for your RIP statements I would do a network command on the subnet not the the Routers LAN interface.

    Thank you every one I got about RIP statement . But I guess I mis configured gateways . Could you please help me out to correct it so that my networks runs ,,,

    Appreciated for yours words !
    thanks
  • miller811miller811 Posts: 897Member
    lebron wrote: »
    Thank you every one I got about RIP statement . But I guess I mis configured gateways . Could you please help me out to correct it so that my networks runs ,,,

    Appreciated for yours words !
    thanks

    The normal process for success, is read the book/or multiple books, icon_study.gifunderstand the theory, and then hit the lab. Hitting the lab or attempting to hit the lab without understanding the theory will not result in the desired effect...

    It may sound harshicon_redface.gif, but that is not what is intended, it is tried and true advice, spoken from experience.icon_thumright.gif
    I don't claim to be an expert, but I sure would like to become one someday.

    Quest for 11K pages read in 2011
    Page Count total to date - 1283
  • captobviouscaptobvious Posts: 648Member
    lebron wrote: »
    Thank you every one I got about RIP statement . But I guess I mis configured gateways . Could you please help me out to correct it so that my networks runs ,,,

    Appreciated for yours words !
    thanks
    Welcome to the forums. Good luck on your studies.

    A bit of advice, no one likes to do your homework for you.
  • abhustlerabhustler ■■□□□□□□□□ Posts: 49Member ■■□□□□□□□□
    Change your default gateway for the PCs in the 172.93.3.0 /22 subnet to point to the fast ethernet port on router A which is 172.93.3.254. Change the default gateway for the PCs in the 172.93.4.0 /23 network to point to the fast ethernet port on router B which is 172.93.5.254 255.255.254.0. However if you arent sure about why you need to do that you may what to consider trying to study for the Net+ before you try getting your CCNA.
    A master at anything was once a beginner
Sign In or Register to comment.