Options
Have aproblem with SDM
sniper_here
Member Posts: 48 ■■□□□□□□□□
in CCNA & CCENT
hi guys
I have cisco router 2600
Router#sh ver
IOS (tm) C2600 Software (C2600-IS-M), Version 12.0(7)XK3, EARLY DEPLOYMENT RELEA
SE SOFTWARE (fc1)
TAC Support: Cisco – Shortcut to Technical Support
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Sun 10-Feb-02 01:29 by dchih
Image text-base: 0x80008088, data-base: 0x80D4AFB0
ROM: System Bootstrap, Version 12.2(6r), RELEASE SOFTWARE (fc1)
ROM: C2600 Software (C2600-IS-M), Version 12.0(7)XK3, EARLY DEPLOYMENT RELEASE S
OFTWARE (fc1)
Router uptime is 0 minutes
System returned to ROM by power-on
System image file is "flash:nss-2620"
cisco 2620 (MPC860) processor (revision 0x00) with 61440K/4096K bytes of memory.
Processor board ID JAD0626CO65 (908809266)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
--More--
when I'm tried to open SDM with it i got message telling me this router not support SDM
can i used new ios to solve the problem ? or its can not be solve?
and if so ,which network simulation support SDM?
THanks
I have cisco router 2600
Router#sh ver
IOS (tm) C2600 Software (C2600-IS-M), Version 12.0(7)XK3, EARLY DEPLOYMENT RELEA
SE SOFTWARE (fc1)
TAC Support: Cisco – Shortcut to Technical Support
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Sun 10-Feb-02 01:29 by dchih
Image text-base: 0x80008088, data-base: 0x80D4AFB0
ROM: System Bootstrap, Version 12.2(6r), RELEASE SOFTWARE (fc1)
ROM: C2600 Software (C2600-IS-M), Version 12.0(7)XK3, EARLY DEPLOYMENT RELEASE S
OFTWARE (fc1)
Router uptime is 0 minutes
System returned to ROM by power-on
System image file is "flash:nss-2620"
cisco 2620 (MPC860) processor (revision 0x00) with 61440K/4096K bytes of memory.
Processor board ID JAD0626CO65 (908809266)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
--More--
when I'm tried to open SDM with it i got message telling me this router not support SDM
can i used new ios to solve the problem ? or its can not be solve?
and if so ,which network simulation support SDM?
THanks
Comments
-
Optionskalebksp Member Posts: 1,033 ■■■■■□□□□□2620s (non-XM) aren't supported by SDM. Here's a list of support routers: SDM 2.5 Release Note [Cisco Router and Security Device Manager] - Cisco Systems
-
OptionsKaminsky Member Posts: 1,2352620s (non-XM) aren't supported by SDM. Here's a list of support routers: SDM 2.5 Release Note [Cisco Router and Security Device Manager] - Cisco Systems
Wow .. that's a good link.Kam. -
Optionssniper_here Member Posts: 48 ■■□□□□□□□□OHHH,I see
can you tell me which router simulation support SDM ?
Thanks very much -
OptionsBl8ckr0uter Inactive Imported Users Posts: 5,031 ■■■■■■■■□□sniper_here wrote: »OHHH,I see
can you tell me which router simulation support SDM ?
Thanks very much
None but GNS3 to my knowledge. SDM is free so if you can find a router (or a copy of the IOS to run in GNS3) that you can connect it to then you don't need a sim for the sdm. -
Optionssniper_here Member Posts: 48 ■■□□□□□□□□Thanks very much guys
Its was very considerate of you to help me and I really appreciate what you do
Finally , I run SDM using GNS3 ,at the begging I had some problem with IOS but now its work
Thanks again