SDM/Telnet

zobo88zobo88 Posts: 60Member ■■□□□□□□□□
Is it necessary to configure SSH on the router or does SDM also works if you have only telnet configured?


Also I was working with GNS3 and wanted to configure SSH, I downloaded a number of ISO images and added them to GNS3 but none of them had the crypto key command ?


is crypto key only available in certain versions ? I am currently using c3640-is-mz_120-7_t.bin

Comments

  • blackninjablackninja Posts: 385Member
    To get SDM runing you need:

    ip address on ethernet interface.

    http and/or https server command set

    a username set with password


    Checkout thread for IOS versions:

    http://www.techexams.net/forums/ccna-security/51366-lab-setup-ccna-security-gns3-real-equipment.html
    Currently studying:
    CCIE R&S - using INE workbooks & videos

    Currently reading:
    Everything. Twice ;)
  • hexemhexem Posts: 177Member
    Yes you need ssh in order to run SDM, it will use ssh when sending the commands when making configurations changes.

    To enable sdm.

    username admin privilege 15 password 0 cisco
    ip http secure-server
    ip http authentication local

    line vty 0 15
    login local
    transport input ssh
    privilege level 15

    and yeh you prolly need to upgrade you're image.
    ICND1 - Passed 25/01/10
    ICND2 - Passed 9/03/10

    Studying CCNA:S
  • blackninjablackninja Posts: 385Member
    hexem wrote: »
    Yes you need ssh in order to run SDM, it will use ssh when sending the commands when making configurations changes.

    To enable sdm.

    username admin privilege 15 password 0 cisco
    ip http secure-server
    ip http authentication local

    line vty 0 15
    login local
    transport input ssh
    privilege level 15

    and yeh you prolly need to upgrade you're image.




    You don't need to setup SSH to run SDM.
    Currently studying:
    CCIE R&S - using INE workbooks & videos

    Currently reading:
    Everything. Twice ;)
  • captobviouscaptobvious Posts: 648Member
    blackninja wrote: »
    To get SDM runing you need:

    ip address on ethernet interface.

    http and/or https server command set

    a username set with password


    Checkout thread for IOS versions:

    http://www.techexams.net/forums/ccna-security/51366-lab-setup-ccna-security-gns3-real-equipment.html
    blackninja wrote:
    You don't need to setup SSH to run SDM.
    +1

    You don't need ssh set up. SDM will run with either http or https. In a lab environment, it's not necessary to use https. That is unless you think your neighbor is sniffing your lan traffic. :D
  • hexemhexem Posts: 177Member
    My bad, well it's always good practise to use ssh ;)
    ICND1 - Passed 25/01/10
    ICND2 - Passed 9/03/10

    Studying CCNA:S
  • zobo88zobo88 Posts: 60Member ■■□□□□□□□□
    OK, I got SDM working with GNS3

    It does work without SSH

    you just need to do following

    username admin privilege 15 password cisco
    ip http server

    line vty 0 15
    login local

    however, I am yet to find an IOS which has the crypto keygen command ?
    now I am using
    Cisco IOS Software, 7200 Software (C7200-IS-M), Version 12.4(13b)
    but still no crypto command
  • tierstentiersten Posts: 4,505Member
    zobo88 wrote: »
    but still no crypto command
    You don't have crypto in the IOS you're running. IS = IP Plus and doesn't contain any of the crypto support.
Sign In or Register to comment.