can not ping btw two olive emulated juniper routers

Hi

I start up two Juniper routers and connect them back to back on int:em5 with IP addresses. I'm not able PING in between then. Any idea what's missing?

Thanks

Find more posts tagged with

Comments

nel

Can you try posting some config? do both of your olives start up ok? what are you running your olives in etc?

raghajar

Hi,

Configuration is very basic, as follow:

junos1: set interface em5 unit 0 family inet address 10.10.10.1/24

junos2: set interface em5 unit 0 family inet address 10.10.10.2/24

then: junos1: ping 10.10.10.2

PING: 10.10.10.2 (10.10.10.2): 56 date bytes

That's all the response I get

Thanks,

Aldur

Can you paste the output from "show system boot-messages"?

raghajar

below pls find output of sh system boot-messages:

Copyright (c) 1996-2009, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
CopyCopyright (c) 1996-2009, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
JUNOS 9.6R1.13 #0: 2009-08-01 09:02:46 UTC
builder@lanath.juniper.net:/volume/build/junos/9.6/release/9.6R1.13/obj-i386/bsd/sys/compile/JUNIPER
MPTable: <QEMUCPU 0.1 >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: QEMU Virtual CPU version 0.14.50 (2377.59-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x633 Stepping = 3
Features=0x781abf9<FPU,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,PGE,CMOV,PAT,MMX,FXSR,SSE,SSE2>
Features2=0x80800001<SSE3,<b23>,<b31>>
real memory = 100597760 (95 MB)
avail memory = 84406272 (80 MB)
ioapic0: Changing APIC ID to 1
ioapic0: Assuming intbase of 0
ioapic0 <Version 1.1> irqs 0-23 on motherboard
Initializing M/T platform properties ..
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
right (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
JUNOS 9.6R1.13 #0: 2009-08-01 09:02:46 UTC
builder@lanath.juniper.net:/volume/build/junos/9.6/release/9.6R1.13/obj-i386/bsd/sys/compile/JUNIPER
MPTable: <QEMUCPU 0.1 >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: QEMU Virtual CPU version 0.14.50 (2377.59-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x633 Stepping = 3
Features=0x781abf9<FPU,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,PGE,CMOV,PAT,MMX,FXSR,SSE,SSE2>
Features2=0x80800001<SSE3,<b23>,<b31>>
real memory = 100597760 (95 MB)
avail memory = 84406272 (80 MB)
ioapic0: Changing APIC ID to 1
ioapic0: Assuming intbase of 0
ioapic0 <Version 1.1> irqs 0-23 on motherboard
Initializing M/T platform properties ..
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 6 Entries> on motherboard
$PIR: BIOS IRQ 11 for 0.5.INTA does not match link 0x60 irq 9
pci0: <PCI bus> on pcib0
$PIR: No matching entry for 0.7.INTA
$PIR: No matching entry for 0.8.INTA
Correcting Natoma config for non-SMP
isab0: <PCI-ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX3 WDMA2 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xc000-0xc00f at device 1.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
smb0: <Intel 82371AB SMB controller> irq 9 at device 1.3 on pci0
pci0: <display, VGA> at device 2.0 (no driver attached)
pci0: <network, ethernet> at device 3.0 (no driver attached)
pci0: <network, ethernet> at device 4.0 (no driver attached)
pci0: <network, ethernet> at device 5.0 (no driver attached)
pci0: <network, ethernet> at device 6.0 (no driver attached)
pci0: <network, ethernet> at device 7.0 (no driver attached)
pci0: <network, ethernet> at device 8.0 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse Explorer, device ID 4
sio0 at port 0x3f8-0x3ff irq 4 flags 0x90 on isa0
sio0: type 16550A, console
sio1: configured irq 5 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio2: configured irq 3 not in bitmap of probed irqs 0
sio2: port may not be enabled
sio3: configured irq 7 not in bitmap of probed irqs 0
sio3: port may not be enabled
Initializing product: 1 ..
Timecounter "TSC" frequency 2377585129 Hz quality 800
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
ad0: Device does not support APM
ad0: 5120MB <QEMU HARDDISK 0.14.50> at ata0-master WDMA2
ad1: Device does not support APM
ad1: 1024MB <QEMU HARDDISK 0.14.50> at ata0-slave WDMA2
Trying to mount root from ufs:/dev/ad0s1a
WARNING: / was not properly dismounted

root@olive2>

Thanks,

Aldur

Hmm, nothing sticks out to me there. Although I'm not to familiar with emulated olives. Can anybody with experience chime in?

maynou_21

How did you connect the two olives? May be you did a mistake. Can you give us the code you used?