Please Help --- Back to Back 2620 via WIC-1DSU-T1 Home Lab

ao3737 · February 2012

Need help configuring back to back 2620 routers using two WIC-1DSU-T1 via cross-over cable.

Problem is that I cannot seem to get protocol link up

Okay I believe I have to cable crimped and crossed-over as needed
1 --> 4
2 --> 5
4 --> 1
5 --> 2
because on both routers I have a solid green CD light.

Router1

Serial settings on Router1
interface Serial0/0
bandwidth 1000
ip address 192.168.4.7 255.255.255.0
service-module t1 clock source internal

Router1#show service-moduleModule type is T1/fractional
Hardware revision is 0.112, Software revision is 20050811-0.3,
Image checksum is 0x80ACD1B3, Protocol revision is 0.1
Receiver has no alarms.
Framing is ESF, Line Code is B8ZS, Current clock source is internal,
Fraction has 24 timeslots (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec.
Last module self-test (done at startup): Passed
Last clearing of alarm counters 01:26:37
loss of signal: 0,
loss of frame: 1, last occurred 01:26:20
AIS alarm: 1, last occurred 01:26:20
Remote alarm: 1, last occurred 01:20:12
Module access errors: 0,
Total Data (last 5 15 minute intervals):
3 Line Code Violations, 460 Path Code Violations
0 Slip Secs, 84 Fr Loss Secs, 3 Line Err Secs, 1 Degraded Mins
3 Errored Secs, 3 Bursty Err Secs, 1 Severely Err Secs, 83 Unavail Secs
Data in current interval (689 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Router1#show interface s0/0
Serial0/0 is up, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Internet address is 192.168.4.7/24
MTU 1500 bytes, BW 1000 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SS7 MTP2, loopback not set
Keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 750 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
5 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

Router1#show controller s0/0
Interface Serial0/0
Hardware is PowerQUICC MPC860 with Integrated FT1 CSU/DSU module
TX and RX clocks detected.
idb at 0x81682F9C, driver data structure at 0x8168AD70
SCC Registers:
General [GSMR]=0x2:0x00000033, Protocol-specific [PSMR]=0x8
Events [SCCE]=0x0340, Mask [SCCM]=0x001F, Status [SCCS]=0x06
Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E
Interrupt Registers:
Config [CICR]=0x00367F80, Pending [CIPR]=0x00008000
Mask [CIMR]=0x40204000, In-srv [CISR]=0x00000000
Command register [CR]=0x600
Port A [PADIR]=0x0000, [PAPAR]=0xFFFF
[PAODR]=0x0000, [PADAT]=0xEEFE
Port B [PBDIR]=0x0180F, [PBPAR]=0x0000E
[PBODR]=0x00000, [PBDAT]=0x3E77D
Port C [PCDIR]=0x00C, [PCPAR]=0x000
[PCSO]=0x020, [PCDAT]=0xFC0, [PCINT]=0x00F
Receive Ring
rmd(680126B0): status 9000 length 60C address 3C47F44
rmd(680126B

: status 9000 length 60C address 3C478C4
rmd(680126C0): status 9000 length 60C address 3C47244
rmd(680126C

: status 9000 length 60C address 3C66984
rmd(680126D0): status 9000 length 60C address 3C66304
rmd(680126D

: status 9000 length 60C address 3C65C84
rmd(680126E0): status 9000 length 60C address 3C65604
rmd(680126E

: status 9000 length 60C address 3C64F84
rmd(680126F0): status 9000 length 60C address 3C64904
rmd(680126F

: status 9000 length 60C address 3C64284
rmd(68012700): status 9000 length 60C address 3C63C04
rmd(6801270

: status 9000 length 60C address 3C63584
rmd(68012710): status 9000 length 60C address 3C62F04
rmd(6801271

: status 9000 length 60C address 3C62884
rmd(68012720): status 9000 length 60C address 3C62204
rmd(6801272

: status 9000 length 60C address 3C61B84
rmd(68012730): status 9000 length 60C address 3C61504
rmd(6801273

: status 9000 length 60C address 3C60E84
rmd(68012740): status 9000 length 60C address 3C60804
rmd(6801274

: status 9000 length 60C address 3C60184
rmd(68012750): status 9000 length 60C address 3C5FB04
rmd(6801275

: status 9000 length 60C address 3C5F484
rmd(68012760): status 9000 length 60C address 3C5EE04
rmd(6801276

: status B000 length 60C address 3C5E784
Transmit Ring
tmd(68012770): status 0 length 0 address 0
tmd(6801277

: status 0 length 0 address 0
tmd(68012780): status 0 length 0 address 0
tmd(6801278

: status 0 length 0 address 0
tmd(68012790): status 0 length 0 address 0
tmd(6801279

: status 0 length 0 address 0
tmd(680127A0): status 0 length 0 address 0
tmd(680127A

: status 0 length 0 address 0
tmd(680127B0): status 0 length 0 address 0
tmd(680127B

: status 0 length 0 address 0
tmd(680127C0): status 0 length 0 address 0
tmd(680127C

: status 0 length 0 address 0
tmd(680127D0): status 0 length 0 address 0
tmd(680127D

: status 0 length 0 address 0
tmd(680127E0): status 0 length 0 address 0
tmd(680127E

: status 2000 length 0 address 0

tx_limited=0(2)

SCC GENERAL PARAMETER RAM (at 0x68013C00)
Rx BD Base [RBASE]=0x26B0, Fn Code [RFCR]=0x18
Tx BD Base [TBASE]=0x2770, Fn Code [TFCR]=0x18
Max Rx Buff Len [MRBLR]=1548
Rx State [RSTATE]=0x200000, BD Ptr [RBPTR]=0x26B0
Tx State [TSTATE]=0x0, BD Ptr [TBPTR]=0x2770

SCC SS7 PARAMETER RAM (at 0x68013C3

CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8
Error-free SUs [EFSUC] = 0
Max frm len [MFLR] = 278
Erm [ERM] = 0x0,N [NOCTETS] = 16, N_cnt [NOCTETS_CNT] = 9, T [ERM_THRESH] = 64, D [ERM_EFSUS] = 256, D_cnt [ERM_EFSUS_CNT] = 256
SS7 options [SS7_OPT] = 0xB
Filter masks [MASK1] = 0xFFFFFFFF, [MASK2] = 0xFF

buffer size 1524

PowerQUICC SCC specific errors:
0 input aborts on receiving flag sequence
0 throttles, 0 enables
0 overruns
0 transmitter underruns
0 transmitter CTS losts
0 aborted short frames

Router2

Serial settings on Router2
interface Serial0/0
ip address 192.168.4.6 255.255.255.0

Router2#show service-module
Module type is T1/fractional
Hardware revision is 0.152, Software revision is 20050811-0.3,
Image checksum is 0x80ACD1B3, Protocol revision is 0.1
Receiver has no alarms.
Framing is ESF, Line Code is B8ZS, Current clock source is line,
Fraction has 24 timeslots (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec.
Last module self-test (done at startup): Passed
Last clearing of alarm counters 01:27:11
loss of signal: 0,
loss of frame: 0,
AIS alarm: 0,
Remote alarm: 0,
Module access errors: 0,
Total Data (last 5 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in current interval (723 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Router2#show interface s0/0
Serial0/0 is up, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Internet address is 192.168.4.6/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SS7 MTP2, loopback not set
Keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1158 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

Router2#show controller s0/0
Interface Serial0/0
Hardware is PowerQUICC MPC860 with Integrated FT1 CSU/DSU module
TX and RX clocks detected.
idb at 0x8175C55C, driver data structure at 0x81764330
SCC Registers:
General [GSMR]=0x2:0x00000033, Protocol-specific [PSMR]=0x8
Events [SCCE]=0x0340, Mask [SCCM]=0x001F, Status [SCCS]=0x06
Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E
Interrupt Registers:
Config [CICR]=0x00367F80, Pending [CIPR]=0x00008000
Mask [CIMR]=0x40204000, In-srv [CISR]=0x00000000
Command register [CR]=0x600
Port A [PADIR]=0x0000, [PAPAR]=0xFFFF
[PAODR]=0x0000, [PADAT]=0xEEFC
Port B [PBDIR]=0x0180F, [PBPAR]=0x0000E
[PBODR]=0x00000, [PBDAT]=0x3E77D
Port C [PCDIR]=0x00C, [PCPAR]=0x000
[PCSO]=0x020, [PCDAT]=0xFC0, [PCINT]=0x00F
Receive Ring
rmd(680126B0): status 9000 length 60C address 3C47F44
rmd(680126B