Line protocol on Interface VoIP-Null0, changed state to upsslinit fn

JeanM

I've googled this but haven't found the fix yet that worked. Have you guys ran into this before and know how to get rid of the following line when the router boots up?

*Mar 1 00:00:04.539: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to upsslinit fn


I've done the confreg change, write erase, reload, ios reload, erase of config...short of erasing the flash completely and reloading via xmodem I can't find anything else.

What is causing the router to show this line even running erase startup-config and then reloading? I've removed the NM-4A/S and NM-1E2W modules and reloaded it and it didn't get rid of it either.



Proceed with reload? [confirm]
*Mar 1 19:29:28.459: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.
System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
C3600 processor with 131072 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
program load complete, entry point: 0x80008000, size: 0x1efab18
Self decompressing the image : ################################################################################################################################################################ [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
000037 0X00056400 Combination Single Ethernet 2 WAN
000024 0X00019A40 Four port Async/Sync
0X00209770 public buffer pools
0X00211000 public particle pools
TOTAL: 0X0048A5B0
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 5Mb.
Using 3 percent iomem. [5Mb/128Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, 3600 Software (C3640-IK9O3S-M), Version 12.4(25d), RELEASE SOFTWARE (fc1)
Technical Support: Support and Documentation - Cisco Systems
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 18-Aug-10 06:59 by prod_rel_team

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
Export Compliance Product Report Application
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco 3640 (R4700) processor (revision 0x00) with 125952K/5120K bytes of memory.
Processor board ID 26747011
R4700 CPU at 100MHz, Implementation 33, Rev 1.0
1 Ethernet interface
4 Low-speed serial(sync/async) interfaces
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of NVRAM.
32768K bytes of processor board System flash (Read/Write)

Press RETURN to get started!

*Mar 1 00:00:04.539: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to upsslinit fn
*Mar 1 00:00:18.875: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
*Mar 1 00:00:18.875: %LINK-3-UPDOWN: Interface Serial1/0, changed state to up
*Mar 1 00:00:18.879: %LINK-3-UPDOWN: Interface Serial1/1, changed state to up
*Mar 1 00:00:18.879: %LINK-3-UPDOWN: Interface Serial1/2, changed state to down
*Mar 1 00:00:18.879: %LINK-3-UPDOWN: Interface Serial1/3, changed state to down
*Mar 1 00:00:20.071: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to up
*Mar 1 00:00:20.071: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to down
*Mar 1 00:00:20.071: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/1, changed state to down
*Mar 1 00:00:20.071: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down
*Mar 1 00:00:20.071: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/3, changed state to down
*Mar 1 00:00:20.203: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 19:29:29.447: %SYS-5-RESTART: System restarted --
Cisco IOS Software, 3600 Software (C3640-IK9O3S-M), Version 12.4(25d), RELEASE SOFTWARE (fc1)
Technical Support: Support and Documentation - Cisco Systems
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 18-Aug-10 06:59 by prod_rel_team
*Mar 1 19:29:29.455: %SNMP-5-COLDSTART: SNMP agent on host SUN is undergoing a cold start
*Mar 1 19:29:29.607: %LINK-5-CHANGED: Interface Serial1/0, changed state to administratively down
*Mar 1 19:29:29.607: %LINK-5-CHANGED: Interface Serial1/1, changed state to administratively down
*Mar 1 19:29:29.607: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down
*Mar 1 19:29:29.607: %LINK-5-CHANGED: Interface Serial1/3, changed state to administratively down
SUN>

JeanM

It must be an IOS thing? I put c3640-i image and the message doesn't come up. Same thing I've seen people post on 26xx series as well...