What is the hardest topic to study for CCNA?

Here's a poll mainly to see on which topics we should focus in our practice exams and TechNotes. The options correspond pretty much with the exam objectives.

Johan

Find more posts tagged with

Free for TechExams community: Cybersecurity salary guide

Compare cert salaries and plan your next career move

Button

Comments

Quench24

IPv6 subnetting

robo78

PPPoE configuration

rob42

To date: OSPF is far and away the hardest topic for me. I'm a little surprised that it's not on the vote. Okay, I can see that 'Routing Protocols' are, but RIP is a walk in the park when compared to OSPF (I.M.H.O).

MAC_Addy

dustervoice wrote: »

Subnetting i struggled with anything other than /24 confuses me even to this day

You just need some good charts. Want me to post some on here?

NavyMooseCCNA

Spanning Tree was one of my weakest areas followed by Frame Relay.

tboe

MAC_Addy wrote: »

You just need some good charts. Want me to post some on here?

I would like to see the charts. more practice for me...

SpetsRepair

Had issues with the same topics as most with the CCNA

WAN Protocols (Frame Relay, ISDN, PPP, etc.)

n4pst3r

IPv6 and all associated protocols and 'ng' (OSPFv3, RIPng...etc) + all changes which came around ithas always been a type.

In the old program CCNAv2, there was a section on fine tunning OSPF (timers, redistribution, LSAs)

Troubleshooting layer 2 problems....

WastedHat

From ICND2 v3 I've found PPPoE and SNMP config to be the hardest to absorb. I've gone through the offical cert guide twice now and I'm comfortable with everything but I've got a bit more work to do before I can configure and troubleshoot those topics without any help.

I'm glad I don't need to do frame relay however I still see it in the CCNP exam topics.

princely jones

I have struggled to understand WAN protocols are things has not be clear for me. To answer your question I feel WAN protocol is the hardest

jws86

Where are these charts?

dotPH

NAT & ACLs has my vote.

crowty

WAN Tech and ACL for me.

Onita

IPv6 for me. We don't use it where I work and I touch a lot of the other stuff.

MustafaIT

I would say WAN technology. It is require knowledge and experience to have better understanding . Everything else you can learn it and apply it with simulation

willieb

When I was teaching CCNA for a couple years, at least for my students each year it was by far:

1.) Subnetting/supernetting

2.) ACLs

hughes1052688

In my opinion the the hardest part of ccna is subnetting,

Learn_everything

I found it quite difficult to get my head around the WAN topics. Especially because a lot of the WAN protocols are outdated and not in use nowadays.

AmeliaA

everything is so hard! but I think, with hardwork, we can do this!

coreyb80

For me it's IPV6 and ACLs.

themanwholaughs

Learning all the commands and making sure their right when you do the exam can be a hard task to do. Lots of practice with a cisco virtual switch and router which you can use in a official lab and you should be good.

unknown

This content has been removed.

pure_cadence

The WAN technology (PPPoE configuration) and IPv6.

emmaganlpwhite

ip address and ACL I guess

khaledit2015

wow this question since i think 2003 on when we were little younger for me subnetting

start it 2015

nagaskdn

For me it's VPN and Frame relay

ps.89

WAN configuration/implementation (such as PPPoE) and IPv6

bigdogz

yes, subnetting for me.

Merrick

Webmaster said:

I agree that if you know nothing about both LAN and WAN they both are as hard to learn. But it is much easier to get hands-on with LAN (home lab for example) than WAN technologies.

Absolutely! LAN gives more accessible experiences for learning than WAN, making it easier for beginners to understand networking basic rules.

Lily02

Bridging/Switching
7-layer OSI Model
Routed Protocols (IP)
Routing Protocol (RIP, IGRP etc.)
WAN Protocols (Frame Relay, ISDN, PPP, etc.)
LAN Technologies
Basic Router Management and Configuration
Access Lists