My lab and its stats, need opinion

here is what my lab consist of.

Router A- 2501- 16mb dram/ 4mb flash 11.0 (boostrap) 11.2(17) IOS
Router B-2501- 16mb dram/ 4mb flash 11.0 (boostrap) 11.2(17) IOS
Router C-2501- 16mb dram/ 4mb flash 11.0 (boostrap) 11.2(17) IOS
Router D- 2611 - 32 MB dram/ 8mb flash 11.3(2)xa4 Booststrap 12.0(3)T3 IOS
Router E- 2611 wierd loading.

Aight first thing is this: my 2501 doesnt seem up to date . (11.2 ???) need an update version of IOS. but which should i choose for each one, there so many, IP plus, enterprise, ect...

and also does the dram and flash on the routers look to low??? ( for newer version IOS)

also i did the same configuration on hyper terminal on each router ( i set it to 9600 tranfer, flow control none and ect.) and the my router E had wierd symbols.

i read that the config could be different, and i would have to use a diffreent trasnfer rate. But how do can i tell which transfer speed to set it up at???

thanks for looking.

here is what my router E did

ùxxx}xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxõøøøøøøøøôøøøøøøøøøøøøøøøøýøøøøøõ
øõøøøøøøøøøøôøøøøøøøøøøøøøøøøøøüøõøøøøøøõøøôøøøøøøøøø

Find more posts tagged with

Free for TechExams community: Cybersecurity salary guide

Compare cert salaries and plan your next career move

Button

Comments

elegua

Hi,

Yeah, you are running low of memory and flash, try upgrade to 16/16 for the 2500 and 64/16 for the 2600.

If you are using windows hyperterminal, open a new session with different rates and try one by one until you see the boot, if you see the boot in one different, just go to line con 0 and just type this: speed 9600 to change it back and do wr mem, reboot, then open a new session with 9600 and you will see the boot.

Hope this help.

lildeezul

thanks i appreciate your help

what would you say on the IOS

elegua

lildeezul wrote:

thanks i appreciate your help

what would you say on the IOS

Hi.

I got my 2500 routers running enterprise because this IOS has IS-IS but for CCNA IP-Plus will be enough.

Hope this help.

lildeezul

ok kwl.. i found out what it was. it is 19200. should i leave it at this. its 19200 better than 9600

here is the sh ver of it

isco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.3(13), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 10-Feb-05 02:11 by ssearch
Image text-base: 0x80008098, data-base: 0x80CD32C8

ROM: System Bootstrap, Version 11.3(2)XA3, PLATFORM SPECIFIC RELEASE SOFTWARE (f
c1)
ROM: C2600 Software (C2600-I-M), Version 12.3(13), RELEASE SOFTWARE (fc2)

rffco012.dhwin2knet.com uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:c2600-i-mz.123-13.bin"

cisco 2611 (MPC860) processor (revision 0x202) with 45056K/4096K bytes of memory
.
Processor board ID JAB0305012R (3902737600)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
2 Ethernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
--More--

here is says 45mb/4mb of memory. if i remeber correctly of 2600's routers you add them right.

can anyone clear this up?? how much dram and flash do i have?

this is Router E, and is currently my most up to date on ( 12.3)

elegua

lildeezul wrote:

ok kwl.. i found out what it was. it is 19200. should i leave it at this. its 19200 better than 9600

here is the sh ver of it

isco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.3(13), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 10-Feb-05 02:11 by ssearch
Image text-base: 0x80008098, data-base: 0x80CD32C8

ROM: System Bootstrap, Version 11.3(2)XA3, PLATFORM SPECIFIC RELEASE SOFTWARE (f
c1)
ROM: C2600 Software (C2600-I-M), Version 12.3(13), RELEASE SOFTWARE (fc2)

rffco012.dhwin2knet.com uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:c2600-i-mz.123-13.bin"

cisco 2611 (MPC860) processor (revision 0x202) with 45056K/4096K bytes of memory
.
Processor board ID JAB0305012R (3902737600)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
2 Ethernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
--More--

here is says 45mb/4mb of memory. if i remeber correctly of 2600's routers you add them right.

can anyone clear this up?? how much dram and flash do i have?

this is Router E, and is currently my most up to date on ( 12.3)

Hi,

To this router you can put one 32MB DRAM and 16MB of flash, you have right now one slot with 32 and one with 16 of DRAM and one of 4 MB of flash, take out the flash and the 16MB of DRAM and replace that for 32/16.

Hope this help.

Hope this help.

lildeezul

it sure does helps thanks a bunch.

also it is set at 19200 transfer rate, should i leave it at this or 9600/

which is better?

jvax

lildeezul wrote:

it sure does helps thanks a bunch.

also it is set at 19200 transfer rate, should i leave it at this or 9600/

which is better?

I'd suggest you change it back to 9600 which is the default for your other routers.

To do that you need to change your config-register in global config mode.