Options
config-register
Fire Starter
Member Posts: 14 ■□□□□□□□□□
in CCNA & CCENT
Hi I'm getting this error message on one lab.
GAD(config)#config-register 0x2102
GAD(config)# exit
GAD(config)# copy run start
Destination filename [startup-config] ? [Enter]
GAD# reload
Proceed with reload? [confirm] [Enter]
00:04:27: %SYS-5-RELOAD: Reload requested
System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2600 platform with 65536 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x3e1c90
Self decompressing the image :: ####
#####
# [OK]
boot of "gsnew-image" using boot helper "flash:c2600-d-mz.120-2.xc2.bin" failed
error returned: File boot failed -- File not accessible
loadprog: error - on file open
boot: cannot load "gsnew-image"
System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2600 platform with 65536 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x3e1c90
Self decompressing the image : #####
.......
16384K bytes of processor board System flash (Read/Write)fc1)
Configuration register is 0x3922o Systems, Inc.
Now.....once the router has rebooted, it should boot from NVRAM
GAD# sh ver should give 0x2102 as the config-register but it has 0x3922
??????
Any feedback would be much appreciated.
BTW, Its set at 115200 baud instead of 9600.
GAD(config)#config-register 0x2102
GAD(config)# exit
GAD(config)# copy run start
Destination filename [startup-config] ? [Enter]
GAD# reload
Proceed with reload? [confirm] [Enter]
00:04:27: %SYS-5-RELOAD: Reload requested
System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2600 platform with 65536 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x3e1c90
Self decompressing the image :: ####
#####
# [OK]
boot of "gsnew-image" using boot helper "flash:c2600-d-mz.120-2.xc2.bin" failed
error returned: File boot failed -- File not accessible
loadprog: error - on file open
boot: cannot load "gsnew-image"
System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2600 platform with 65536 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x3e1c90
Self decompressing the image : #####
.......
16384K bytes of processor board System flash (Read/Write)fc1)
Configuration register is 0x3922o Systems, Inc.
Now.....once the router has rebooted, it should boot from NVRAM
GAD# sh ver should give 0x2102 as the config-register but it has 0x3922
??????
Any feedback would be much appreciated.
BTW, Its set at 115200 baud instead of 9600.
Comments
-
Options
keenon
Member Posts: 1,922 ■■■■□□□□□□
thats interesting i haven't seem that before..
question when your saving does it really look like
GAD(config)# copy run start
[/list][/url]Become the stainless steel sharp knife in a drawer full of rusty spoons -
OptionsMax4Speed
Member Posts: 1 ■□□□□□□□□□
Just trying to get an idea, what exactly are you trying to do? I didnt see the INITIALIZE command up there.Trying to Study for CCNA!