I need help figuring out this 1750 with a voice card

Router#sh diag
Slot 0:
C1750 1FE VE Mainboard Port adapter, 4 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 8.1
PCB Serial Number : JAD05290KHX
Part Number : 73-3743-08
Board Revision : A0
Fab Version : 04
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 C9 41 08 01 C1 8B 4A 41 44 30 35 32
0x10: 39 30 4B 48 58 82 49 0E 9F 08 42 41 30 02 04 FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Packet Voice DSP Module Slot 0:
Not populated

WIC Slot 0:
Ethernet 10bT WAN daughter card-Version 4 TLV Cookie Format
Hardware Revision : 3.0
Part Number : 73-5797-03
Board Revision : A0
Deviation Number : 0-0
Fab Version : 02
PCB Serial Number : VMS0626074U
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Top Assy. Part Number : 800-09311-03
Connector Type : 01
Chassis MAC Address : 0004.dc0c.eacf
MAC Address block size : 1

WIC Slot 2:
Dual FXO Voice Interface Card
Hardware revision 1.1 Board revision K0
Serial number 0027350764 Part number 800-02495-01
Test history 0x00 RMA number 00-00-00
Connector type WAN Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 0D 01 01 01 A1 56 EC 50 09 BF 01 00 00 00 00
0x30: A0 59 52 00 01 12 14 01 FF FF FF FF FF FF FF FF

When I do a show diag I see the voice card but when I do a show run I don't see any voice ports. Do I have to add Pvdm to the router?

Find more posts tagged with

Comments

mikej412

mrblackmamba343 wrote: »

Do I have to add Pvdm to the router?

Yes, you need to install a PVDM to support VIC cards. Plus make sure you have an IOS that supports vioce.

Troubleshooting Unrecognized Voice Interface Cards on Cisco 1750, 1751, and 1760 Routers - Cisco Systems

Analog FXS and FXO hardware support on Cisco 175x platforms - Ciscowiki

mrblackmamba343

mikej412 wrote: »

Yes, you need to install a PVDM to support VIC cards. Plus make sure you have an IOS that supports vioce.

Troubleshooting Unrecognized Voice Interface Cards on Cisco 1750, 1751, and 1760 Routers - Cisco Systems

Analog FXS and FXO hardware support on Cisco 175x platforms - Ciscowiki

I know for a fact the IOS supports voice because I have been able to create voip dial-peers, translations patterns and digit manipulations.

mrblackmamba343

My PVDM card came in today. After I put it in the router, I could see both ports

Router(config)#do sh voice port summ
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
========= == ============ ===== ==== ======== ======== ==
2/0 -- fxo-ls up dorm idle on-hook y
2/1 -- fxo-ls up dorm idle on-hook y

mrblackmamba343

.........