Options

How to find clock rate

Dilbert65Dilbert65 Member Posts: 73 ■■□□□□□□□□
in CCNP
Lets say your isp CIR is 56k. What command can you run on the dte to make sure that they set the clockrate to 56k?

I use "show int s0" and the bandwidth is showing 1544 but I know my frame cloud is set at 56k.

Thanks
· Share on FacebookShare on Twitter

Comments

  • Options
    billscott92787billscott92787 Member Posts: 933
    Dilbert65 wrote: »
    Lets say your isp CIR is 56k. What command can you run on the dte to make sure that they set the clockrate to 56k?

    I use "show int s0" and the bandwidth is showing 1544 but I know my frame cloud is set at 56k.

    Thanks



    The bandwidth command doesn't mean that you are "officially" transmitting 1.544 Mbps over that link into the cloud. The rate in that case would be controlled by the provider, and would be throttled once it got to the cloud. The bandwidth command is used more for reference for routing protocols such as EIGRP and OSPF when computing the metrics. You could set your bandwidth to match the clock rate of the frame, which would change your metrics in your routing table. But, the ISP controls the clocking process since they have ownership over the DCE device.
    · Share on FacebookShare on Twitter
  • Options
    mikej412mikej412 Member Posts: 10,086 ■■■■■■■■■■
    show controllers serial 0
    :mike: Cisco Certifications -- Collect the Entire Set!
    · Share on FacebookShare on Twitter
  • Options
    Dilbert65Dilbert65 Member Posts: 73 ■■□□□□□□□□
    I understand that the provider sets the clock rate but I want to know if there is a command to see what clock rate they are tranmitting to me.

    If I do "show controllers s 0" I get

    R1#show control ser 0
    HD unit 0, idb = 0x12797C, driver structure at 0x12DD08
    buffer size 1524 HD unit 0, V.35 DTE cable
    cpb = 0xE2, eda = 0x4140, cda = 0x4000
    RX ring with 16 entries at 0xE24000
    00 bd_ptr=0x4000 pak=0x12EFA4 ds=0xE27908 status=80 pak_size=0
    01 bd_ptr=0x4014 pak=0x12F44C ds=0xE28680 status=80 pak_size=0
    02 bd_ptr=0x4028 pak=0x12F6A0 ds=0xE28D3C status=80 pak_size=0
    03 bd_ptr=0x403C pak=0x12F8F4 ds=0xE293F8 status=80 pak_size=0
    04 bd_ptr=0x4050 pak=0x12FB48 ds=0xE29AB4 status=80 pak_size=0
    05 bd_ptr=0x4064 pak=0x12FD9C ds=0xE2A170 status=80 pak_size=0
    06 bd_ptr=0x4078 pak=0x12FFF0 ds=0xE2A82C status=80 pak_size=0
    07 bd_ptr=0x408C pak=0x130244 ds=0xE2AEE8 status=80 pak_size=0
    08 bd_ptr=0x40A0 pak=0x130498 ds=0xE2B5A4 status=80 pak_size=0
    09 bd_ptr=0x40B4 pak=0x1306EC ds=0xE2BC60 status=80 pak_size=0
    10 bd_ptr=0x40C8 pak=0x130940 ds=0xE2C31C status=80 pak_size=0
    11 bd_ptr=0x40DC pak=0x130B94 ds=0xE2C9D8 status=80 pak_size=0
    12 bd_ptr=0x40F0 pak=0x130DE8 ds=0xE2D094 status=80 pak_size=0
    13 bd_ptr=0x4104 pak=0x13103C ds=0xE2D750 status=80 pak_size=0
    14 bd_ptr=0x4118 pak=0x131290 ds=0xE2DE0C status=80 pak_size=0
    15 bd_ptr=0x412C pak=0x1314E4 ds=0xE2E4C8 status=80 pak_size=0
    16 bd_ptr=0x4140 pak=0x131738 ds=0xE2EB84 status=80 pak_size=0
    cpb = 0xE2, eda = 0x4800, cda = 0x4800
    TX ring with 1 entries at 0xE24800
    00 bd_ptr=0x4800 pak=0x000000 ds=0x000000 status=80 pak_size=0
    01 bd_ptr=0x4814 pak=0x000000 ds=0x000000 status=80 pak_size=0
    0 missed datagrams, 0 overruns
    0 bad datagram encapsulations, 0 memory errors
    0 transmitter underruns
    0 residual bit errors


    which does not say 56k.
    · Share on FacebookShare on Twitter
  • Options
    mikej412mikej412 Member Posts: 10,086 ■■■■■■■■■■
    Well, you can try the show service-module command next or actually tell us what kind of hardware/port you're using.
    :mike: Cisco Certifications -- Collect the Entire Set!
    · Share on FacebookShare on Twitter
  • Options
    Dilbert65Dilbert65 Member Posts: 73 ■■□□□□□□□□
    I have a 2620xm with 4 serail port module.
    Frame Setup

    interface Serial1/1
    no ip address
    encapsulation frame-relay
    logging event subif-link-status
    logging event dlci-status-change
    clock rate 56000
    no frame-relay inverse-arp
    frame-relay intf-type dce
    frame-relay route 122 interface Serial1/2 221
    frame-relay route 123 interface Serial1/3 321


    the clients is a 2501 with ios 12.1 and a 2611xm with IOS 12.2.

    I thought maybe there was a simple command to se what the clock rate on the dce had been set to from the dte router command line :)

    The "show service-module" command does not work on any of my equipment. If I do a "show s?" the only command is sessions.

    thanks for feedback
    · Share on FacebookShare on Twitter
Sign In or Register to comment.