I just received the NM-8A/S module for my 2620 router. I installed it and powered on the router, and the module's led turns on, as well.
When I logged in, and execute the command show ip int brief, the only interface I can see is the fa0/0 of the 2620.
Btw, the router does not have any config at all.
Did I get a faulty module again?
Here some part of the bootup of the my 2620
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.3(22), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Wed 24-Jan-07 16:48 by ccai
Image text-base: 0x80008098, data-base: 0x80CEA424
cisco 2620 (MPC860) processor (revision 0x00) with 27648K/5120K bytes of memory.
Processor board ID JAD06170A1P (656604760)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
interface Serial1/0
^
% Invalid input detected at '^' marker.
no ip address
% Incomplete command.
shutdown
^
% Invalid input detected at '^' marker.
interface Serial1/1
^
% Invalid input detected at '^' marker.
no ip address
% Incomplete command.
shutdown
^
% Invalid input detected at '^' marker.
interface Serial1/2
^
% Invalid input detected at '^' marker.
no ip address
% Incomplete command.
shutdown
^
% Invalid input detected at '^' marker.
interface Serial1/3
^
% Invalid input detected at '^' marker.
no ip address
% Incomplete command.
shutdown
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
Bad Hardware in bay/slot/sub_slot = 1/-1/-1
*Mar 1 00:00:07.471: %PA-3-NOTSUPPORTED: PA in slot1 (Unknown (type 0)) is not supported on this im
age.
Please issue "show diag" in fully loaded IOS image
to get the PA's information and verify if it is supported
by this image, a newer version may be needed.
*Mar 1 00:00:09.723: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar 1 00:00:10.891: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state
to down
*Mar 1 00:00:11.647: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:00:12.279: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively
down
*Mar 1 00:00:13.923: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.3(22), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Wed
Here is the show diag:
Router#show diag
Slot 0:
C2620 1FE Mainboard Port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 0.0
PCB Serial Number : JAD06170A1P (656604760)
Part Number : 73-2843-11
RMA History : 00
RMA Number : 0-0-0-0
Board Revision : A0
Deviation Number : 0-0
Product (FRU) Number : C2620 - 1FE
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 94 41 00 00 C1 17 4A 41 44 30 36 31
0x10: 37 30 41 31 50 20 28 36 35 36 36 30 34 37 36 30
0x20: 29 82 49 0B 1B 0B 04 00 81 00 00 00 00 42 41 30
0x30: 80 00 00 00 00 FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Slot 1:
Unknown (type 0) Port adapter
Port adapter is disabled
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 0.0 Board revision UNKNOWN
Serial number 0 Part number 00-0000-00
FRU Part Number: PA-1FE-TX-nISL=
Test history 0x0 RMA number 00-00-00
EEPROM format version 0
EEPROM contents (hex):
0x00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Router#Bad Hardware in bay/slot/sub_slot = 1/-1/-1
