FXS/FXO card problem
auos
Member Posts: 186
Hi,
I have 2801 router with 128/64 memory no PVDM, I buy two VIC-2FXO and VIC-2FXS, but when I plugged in to my router and router starting booting I get below messages: -
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0X003AA110 public buffer pools
0X00211000 public particle pools
0X00020000 Crypto module pools
0X00120000 VPM buffer pools
0X000D 0X00000000 UNKNOWN Card in slot 0
0X000E 0X00000000 UNKNOWN Card in slot 2
0X000021B8 Onboard USB
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
*Oct 22 11:51:42.307: %CFG-3-CARD_NOT_SUPPORTED: Slot 0: FXO Voice daughter card (2 port), Part# 80-2495-1, HW-Rev 1.1, Board-Rev J0, S/N 25072539
*Oct 22 11:51:42.347: %CFG-3-CARD_NOT_SUPPORTED: Slot 2: FXS Voice daughter card (2 port), Part# 80-2493-4, HW-Rev 1.1, Board-Rev B0, S/N 27276481
*Oct 22 11:51:45.399: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
And when I try the command (show voice port summ) I got nothing?
What is my problem, is that mean the two card have H/W problem.
I have 2801 router with 128/64 memory no PVDM, I buy two VIC-2FXO and VIC-2FXS, but when I plugged in to my router and router starting booting I get below messages: -
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0X003AA110 public buffer pools
0X00211000 public particle pools
0X00020000 Crypto module pools
0X00120000 VPM buffer pools
0X000D 0X00000000 UNKNOWN Card in slot 0
0X000E 0X00000000 UNKNOWN Card in slot 2
0X000021B8 Onboard USB
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
*Oct 22 11:51:42.307: %CFG-3-CARD_NOT_SUPPORTED: Slot 0: FXO Voice daughter card (2 port), Part# 80-2495-1, HW-Rev 1.1, Board-Rev J0, S/N 25072539
*Oct 22 11:51:42.347: %CFG-3-CARD_NOT_SUPPORTED: Slot 2: FXS Voice daughter card (2 port), Part# 80-2493-4, HW-Rev 1.1, Board-Rev B0, S/N 27276481
*Oct 22 11:51:45.399: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
And when I try the command (show voice port summ) I got nothing?
What is my problem, is that mean the two card have H/W problem.
Comments
many thanks mike your are amazing, I will try to buy PVDM2-8 is that enough?
Many thanks, please correct me if I wrong, if I have 2600xm module and I need to supported as voice router that mean I should have (NM-2V or NM-1V) and also AIM-ATM-VOICE-30 for DSP resource.
not sure but read the cisco doc carefully on the difference between aim-atm-voice ant aim-voice..
1. you can certianly assign all channels to One interface with both aim cards.
2. with ATM_AIM card you can assign more than one interface but i think its limited in some way.. check cisco docs before you buy the AIM.
One (or two) of the Voice AIMs supposedly give you the ability to run a digital VWIC in a WIC slot.....
I just went with the NM-HDV (Network Module - High Density Voice) to support the VWIC-1MFT-T1 and VWIC-2MFT-T1 cards -- and the 1760 routers, which have VIC slots and support the digital cards without an additional carrier.
The NM-HDV has 5 slots for PVDMs. There are the newer (and more expensive) versions if you have newer (and more expensive) routers.