Compare cert salaries and plan your next career move
mikej412 wrote: » You didn't tell us the password recovery link you used or paste the output of your terminal session so we could see what you did -- so it's hard to guess why it isn't working for you. Did you compare your output to the example password recovery terminal output and look for where it's different? If the no service password-recovery option was set you wouldn't be able to see the current configuration, but you'd still be able to nuke it and get to the router setup option.
Password: ü System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1) Copyright (c) 2003 by cisco Systems, Inc. C2600 platform with 131072 Kbytes of main memory monitor: command "boot" aborted due to user interrupt rommon 1 > confreg 0x2142 You must reset or power cycle for new config to take effect rommon 2 > reset System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1) Copyright (c) 2003 by cisco Systems, Inc. C2600 platform with 131072 Kbytes of main memory program load complete, entry point: 0x80008000, size: 0x9d57b0 Self decompressing the image : ######################################################### ######################################################################################## ############################################## [OK] Smart Init is enabled smart init is sizing iomem ID MEMORY_REQ TYPE 00036E 0X000BA600 C2650XM Single Fast Ethernet 0X000F3BB0 public buffer pools 0X00211000 public particle pools TOTAL: 0X003BF1B0 If any of the above Memory Requirements are "UNKNOWN", you may be using an unsupported configuration or there is a software problem and system operation may be compromised. Rounded IOMEM up to: 4Mb. Using 3 percent iomem. [4Mb/128Mb] Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-IS-M), Version 12.2(29), RELEASE SOFTWARE (fc3) Technical Support: Cisco - Shortcut Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 11-May-05 17:27 by kellmill Image text-base: 0x8000808C, data-base: 0x8111B348 cisco 2650XM (MPC860P) processor (revision 0x200) with 126976K/4096K bytes of memory. Processor board ID JAE080411WW (742437874) M860 processor: part number 5, mask 2 Bridging software. X.25 software, Version 3.0.0. 1 FastEthernet/IEEE 802.3 interface(s) 1 Serial network interface(s) 32K bytes of non-volatile configuration memory. 49152K bytes of processor board System flash (Read/Write) class VIDEO-** bandwidth percent 35 ^ % Invalid input detected at '^' marker. service-module t1 clock source internal ^ % Invalid input detected at '^' marker. % Invalid input detected at '^' marker. 10.79.64.80 0.0.0.1 ^ % Invalid input detected at '^' marker. ost 144.226. 211.17 % Invalid input detected at '^' marker. community mnsreadonly RO 66 % Invalid input detected at '^' marker. snmp-server enable traps isdn call-information ^ % Invalid input detected at '^' marker. Press RETURN to get started! 00:00:08: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up 00:00:08: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down *Mar 1 00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, chang ed state to down *Mar 1 00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed sta te to down *Mar 1 00:00:12: %SYS-5-CONFIG_I: Configured from memory by console *Mar 1 00:00:14: %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-IS-M), Version 12.2(29), RELEASE SOFTWARE (fc3) Technical Support: Cisco - Shortcut Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 11-May-05 17:27 by kellmill *Mar 1 00:00:14: %SNMP-5-COLDSTART: SNMP agent on host RTNCCARDR01 is undergoing a cold start UNAUTHORIZED ACCESS PROHIBITED ****************************************************** Access to this system and associated network, computer resource, or data is restricted to those authorized by the company. This system and related networks, resources or data may only be used for business purposes of the company and its customers. Use by unauthorized individuals or for an unauthorized purpose is a violation of Federal and/or State law. Violators will be prosecuted. ******************************************************* Device is supported by MDS RTNCCARDR01 line 0 User Access Verification Password:
--- System Configuration Dialog --- Would you like to enter the initial configuration dialog? [yes/no]: Press RETURN to get started!
Password: ü
mikej412 wrote: » I don't see an answer typed in. Did you type in no? Or did you hit return? If you don't care about sneaking a peek at the existing configuration, then yes is the other option to try.
mikej412 wrote: » What's your terminal software and configuration?
mark076h wrote: » Sometimes I don't get that option. but i did the control c to skip it in that example.
mikej412 wrote: » What happens when you type in no as the example shows? You may not get the option if your terminal configuration is off. You've got a couple of character skips in your terminal session output so you may be sending some "input" you shouldn't. That's why I asked about your terminal settings -- what did you configure for flow control?
ü System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1) Copyright (c) 2003 by cisco Systems, Inc. C2600 platform with 131072 Kbytes of main memory monitor: command "boot" aborted due to user interrupt rommon 1 > confreg 0x2142 You must reset or power cycle for new config to take effect rommon 2 > reset System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1) Copyright (c) 2003 by cisco Systems, Inc. C2600 platform with 131072 Kbytes of main memory program load complete, entry point: 0x80008000, size: 0x9d57b0 Self decompressing the image : ################################################# ################################################################################ ############################################################## [OK] Smart Init is enabled smart init is sizing iomem ID MEMORY_REQ TYPE 00036E 0X000BA600 C2650XM Single Fast Ethernet 0X000F3BB0 public buffer pools 0X00211000 public particle pools TOTAL: 0X003BF1B0 If any of the above Memory Requirements are "UNKNOWN", you may be using an unsupported configuration or there is a software problem and system operation may be compromised. Rounded IOMEM up to: 4Mb. Using 3 percent iomem. [4Mb/128Mb] Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-IS-M), Version 12.2(29), RELEASE SOFTWARE (fc3) Technical Support: Cisco - Shortcut Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 11-May-05 17:27 by kellmill Image text-base: 0x8000808C, data-base: 0x8111B348 cisco 2650XM (MPC860P) processor (revision 0x200) with 126976K/4096K bytes of me mory. Processor board ID JAE080411WW (742437874) M860 processor: part number 5, mask 2 Bridging software. X.25 software, Version 3.0.0. 1 FastEthernet/IEEE 802.3 interface(s) 1 Serial network interface(s) 32K bytes of non-volatile configuration memory. 49152K bytes of processor board System flash (Read/Write) class map VIDEO-** not configured --- System Configuration Dialog --- Would you like to enter the initial configuration dialog? [yes/no]: no Would you like to terminate autoinstall? [yes]: yes Press RETURN to get started! 00:00:08: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up 00:00:08: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down *Mar 1 00:00:08: %PARSER-4-BADCFG: Unexpected end of configuration file. *Mar 1 00:00:08: %SYS-5-CONFIG_I: Configured from memory by console *Mar 1 00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/ 0, changed state to down *Mar 1 00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, cha nged state to down *Mar 1 00:00:39: %IP-5-WEBINST_KILL: Terminating DNS process *Mar 1 00:00:39: %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-IS-M), Version 12.2(29), RELEASE SOFTWARE (fc3) Technical Support: Cisco - Shortcut Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 11-May-05 17:27 by kellmill *Mar 1 00:00:39: %SNMP-5-COLDSTART: SNMP agent on host RTNCCARDR01 is undergoin g a cold start *Mar 1 00:00:39 RTNCCARDR01 li: %LINK-5-CHANGED: Interface Serial0/0, changed state to administr atively down *Mar 1 00:00:39: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to a dministratively downne 0 User Access Verification Password: % Access denied
mark076h wrote: » I have flow control set to NONE. this is what i get if i type in NO. autoinstall is not mentioned in the guides. I try no and yes and it does not work either way.
mikej412 wrote: » What's the output for the yes option -- it should start asking you about the configuration you want, rather than the terminate autoinstall question. NONE sounds like a Parity option. Flow control is usually CTS/RTS or XON/XOFF or DTR/DSR
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1) Copyright (c) 2003 by cisco Systems, Inc. C2600 platform with 131072 Kbytes of main memory monitor: command "boot" aborted due to user interrupt rommon 1 > confreg 0x2142 You must reset or power cycle for new config to take effect rommon 2 > reset System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1) Copyright (c) 2003 by cisco Systems, Inc. C2600 platform with 131072 Kbytes of main memory program load complete, entry point: 0x80008000, size: 0x9d57b0 Self decompressing the image : ################################################# ################################################################################ ############################################################## [OK] Smart Init is enabled smart init is sizing iomem ID MEMORY_REQ TYPE 00036E 0X000BA600 C2650XM Single Fast Ethernet 0X000F3BB0 public buffer pools 0X00211000 public particle pools TOTAL: 0X003BF1B0 If any of the above Memory Requirements are "UNKNOWN", you may be using an unsupported configuration or there is a software problem and system operation may be compromised. Rounded IOMEM up to: 4Mb. Using 3 percent iomem. [4Mb/128Mb] Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-IS-M), Version 12.2(29), RELEASE SOFTWARE (fc3) Technical Support: Cisco - Shortcut Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 11-May-05 17:27 by kellmill Image text-base: 0x8000808C, data-base: 0x8111B348 cisco 2650XM (MPC860P) processor (revision 0x200) with 126976K/4096K bytes of me mory. Processor board ID JAE080411WW (742437874) M860 processor: part number 5, mask 2 Bridging software. X.25 software, Version 3.0.0. 1 FastEthernet/IEEE 802.3 interface(s) 1 Serial network interface(s) 32K bytes of non-volatile configuration memory. 49152K bytes of processor board System flash (Read/Write) --- System Configuration Dialog --- Would you like to enter the initial configuration dialog? [yes/no]: yes At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system Would you like to enter basic management setup? [yes/no]: no First, would you like to see the current interface summary? [yes]: n Configuring global parameters: Enter host name [Router]: Router The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter enable secret: mark The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images. Enter enable password: mark2 The virtual terminal password is used to protect access to the router over a network interface. Enter virtual terminal password: mark3 Configure SNMP Network Management? [yes]: n Configure IP? [yes]: n Configure bridging? [no]: n Async lines accept incoming modems calls. If you will have users dialing in via modems, configure these lines. Configure Async lines? [yes]: n Configuring interface parameters: Do you want to configure FastEthernet0/0 interface? [yes]: n Do you want to configure Serial0/0 interface? [yes]: n The following configuration command script was created: hostname Router enable secret 5 $1$X1XF$C0LV9FHxiBKfPjx0xbvv3/ enable password mark2 line vty 0 4 password mark3 no snmp-server ! no ip routing no bridge 1 ! interface FastEthernet0/0 shutdown no ip address ! interface Serial0/0 shutdown no ip address dialer-list 1 protocol ip permit dialer-list 1 protocol ipx permit ! end [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. Enter your selection [2]: 2 Building configuration... EEPROM byte write error - timeout[OK] Use the enabled mode 'configure' command to modify this configuration. Press RETURN to get started! 00:00:08: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up 00:00:08: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down 00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, chang ed state to down 00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed sta te to down 00:01:11: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administr atively down 00:01:11: %LINK-5-CHANGED: Interface Serial0/0, changed state to administrativel y down 00:01:31: %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-IS-M), Version 12.2(29), RELEASE SOFTWARE (fc3) Technical Support: Cisco - Shortcut Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 11-May-05 17:27 by kellmill 00:01:31: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold star t Router>
00:02:02: %ALIGN-3-SPURIOUS: Spurious memory access made at 0x81117480 reading 0x24D4 00:02:02: %ALIGN-3-TRACE: -Traceback= 81117480 804542DC 80454A08 803F7E60 8032EFE4 8032EF58 80362EBC 803637B8 00:02:02: %ALIGN-3-TRACE: -Traceback= 811174DC 804542DC 80454A08 803F7E60 8032EFE4 8032EF58 80362EBC 803637B8 Router> Router>write erase ^ % Invalid input detected at '^' marker. Router>write Translating "write"...domain server (255.255.255.255) Translating "write"...domain server (255.255.255.255) (255.255.255.255)% Unknown command or computer name, or unable to find computer address Router>? Exec commands: access-enable Create a temporary Access-List entry access-profile Apply user-profile to interface clear Reset functions connect Open a terminal connection disable Turn off privileged commands disconnect Disconnect an existing network connection enable Turn on privileged commands exit Exit from the EXEC help Description of the interactive help system lock Lock the terminal login Log in as a particular user logout Exit from the EXEC mrinfo Request neighbor and version information from a multicast router mstat Show statistics after multiple multicast traceroutes mtrace Trace reverse multicast path from destination to source name-connection Name an existing network connection pad Open a X.29 PAD connection ping Send echo messages ppp Start IETF Point-to-Point Protocol (PPP) resume Resume an active network connection rlogin Open an rlogin connection show Show running system information slip Start Serial-line IP (SLIP) systat Display information about terminal lines tclquit Quit Tool Command Language shell tclsh Tool Command Language shell telnet Open a telnet connection terminal Set terminal line parameters traceroute Trace route to destination tunnel Open a tunnel connection udptn Open an udptn connection where List active connections x28 Become an X.28 PAD x3 Set X.3 parameters on PAD Router> Router> Router> Router>enable Password: Router#write Building configuration... [OK] NVRAM Verification Failed Router#show running-config Building configuration... Current configuration : 621 bytes ! version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname Router ! enable secret 5 $1$X1XF$C0LV9FHxiBKfPjx0xbvv3/ enable password mark2 ! ip subnet-zero no ip routing ! ! ! call rsvp-sync ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address no ip route-cache shutdown duplex auto speed auto ! interface Serial0/0 no ip address no ip route-cache shutdown ! ip classless ip http server ! dialer-list 1 protocol ip permit dialer-list 1 protocol ipx permit ! dial-peer cor custom ! ! ! ! line con 0 line aux 0 line vty 0 4 password mark3 login ! end Router# Router# Router# Router# Router# Router# Router# Router#copy running-config startup-config Destination filename [startup-config]? Building configuration... 00:06:02: %ALIGN-3-SPURIOUS: Spurious memory access made at 0x81117480 reading 0x2C4 00:06:02: %ALIGN-3-TRACE: -Traceback= 81117480 804542DC 80454A08 803F7E60 8032EFE4 8032EF58 8035D78C 803514EC 00:06:02: %ALIGN-3-TRACE: -Traceback= 811174DC 804542DC 80454A08 803F7E60 8032EFE4 8032EF58 8035D78C 803514EC[OK] NVRAM Verification Failed Router#
Router#show startup-config %Error opening nvram:/startup-config (Invalid Checksum) Router#
Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#line console 0 Router(config-line)#password mark Router(config-line)#login Router(config-line)#exit Router(config)#end Router#show 00:02:52: %SYS-5-CONFIG_I: Configured from console by console ru % Ambiguous command: "show ru" Router#show running-config Building configuration... Current configuration : 432 bytes ! version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname Router ! ! ip subnet-zero ! ! ! call rsvp-sync ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface Serial0/0 no ip address shutdown ! ip classless ip http server ! ! dial-peer cor custom ! ! ! ! line con 0 password mark login line aux 0 line vty 0 4 ! end Router# Router# Router# Router#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] NVRAM Verification Failed Router#show startup-config %Error opening nvram:/startup-config (Invalid Checksum) Router#
mikej412 wrote: » You may have bad NVRAM. Try the erase NVRAM: command And then see if you have the squeeze NVRAM: command If the router does have bad NVRAM and you can't return it, you can try to boot by getting the configuration from the network with the service config command (after setting an option or two with the boot command).
mikej412 wrote: » It may be case sensitive -- see what the command line help says and try that. It may be erase nvram: rather than erase NVRAM:
mikej412 wrote: » You can try a Hail Mary IOS upgrade on the off chance that the issue is caused by a corrupted IOS image trying to write to the wrong memory location. Otherwise check out this thread: http://www.techexams.net/forums/ccna-ccent/50540-fried-nvram.html
mark076h wrote: » when i do memory test command it says it passes.
mikej412 wrote: » That's good news. If none of the normal NVRAM recovery steps worked, than that would mean trying a different known good IOS image might have a chance of solving the problem (rather than being a long shot).
Router>en Router#erase nv Erasing the nvram filesystem will remove all configuration files! Continue? [con firm] [OK] Erase of nvram: complete Router# 00:02:14: %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram
router#copy run start Destination filename [startup-config]? Bad configuration memory structure -- try rewriting Building configuration... EEPROM write error - timeout[OK] Bad configuration memory structure -- try rewriting Bad configuration memory structure -- try rewriting router#
router#show start Bad configuration memory structure -- try rewriting Using 723 out of 29688 bytes router# router#reload System configuration has been modified. Save? [yes/no]: yes Bad configuration memory structure -- try rewriting Building configuration... EEPROM write error - timeout[OK] Bad configuration memory structure -- try rewriting Bad configuration memory structure -- try rewriting Proceed with reload? [confirm]
mark076h wrote: » I thought i had it working after an IOS upgrade but after having the router off for awhile then turning it back on it lost the config and now I am getting this:
mark076h wrote: » now I am getting this:
mikej412 wrote: » That would have been a good time to do the memory test.
Compare salaries for top cybersecurity certifications. Free download for TechExams community.
