Options
Intel Nic Teaming - Really Stuck
![BroadcastStorm](https://us.v-cdn.net/6030959/uploads/userpics/navatar229699_4.gif)
in CCNP
Hi Guys, this is something I've been stuck so far I am attempting to configure ANS Teaming on a Quad Intel card, what throws me off is I was attempting to mirror one of the configuration on one of our server that is also utilizing ANS teaming, I've uploaded a screenshot, but for some reason my configs is not working I am able to sent but unable to receive on the TEAM #0 the nic team interface, has anyone encountered this issue? I am using 802.1ad Dynamic Link Aggregation.
Thanks!
Thanks!
Comments
-
Options
down77 Member Posts: 1,009
Post your switch config. If you are using 802.3ad (Link Agg) make sure the ether-channel configuration on the switch matches appropriately.CCIE Sec: Starting Nov 11 -
Options
BroadcastStorm Member Posts: 496
Switch is a Foundry ughhh
Trunk ID: 209
Hw Trunk ID: 2
Ports_Configured: 4
Primary Port Monitored: Jointly
Ports 4/17 4/18 4/19 4/20
Port Names none none none none
Port_Status enable enable enable enable
Monitor off off off off
Rx Mirr Port N/A N/A N/A N/A
Tx Mirr Port N/A N/A N/A N/A
Monitor Dir N/A N/A N/A N/A
Ports are untagged on VLAN 1
The servers mobo was replaced, and another error was thrown at me when I was statically configuring an IP address, I used the articile to fix it.
http://support.microsoft.com/kb/269155 -
Options
BroadcastStorm Member Posts: 496
Driver was reinstalled, and other things network was complaining about a hidden drivers when I try to statically set IP address, thanks guys! -
Options
BroadcastStorm Member Posts: 496
This is still not working, any advise will be great
For some reason link-aggregation has negotiated, but the TEAM network on the server side windows 2003 quad port configured for dynamic link aggregation is only sending packets but received is 0, I am wondering if LACP has to be set on both end as full or half duplex.
Foundry configs
Port [Sys P] [Port P] [ Key ] [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope]
4/13 1 1 480 Yes L Agg Syn Col Dis No No Ope
4/14 1 1 480 Yes L Agg Syn Col Dis No No Ope
4/15 1 1 480 Yes L Agg Syn Col Dis No No Ope
4/16 1 1 480 Yes L Agg Syn Col Dis No No Ope
interface ethernet 4/13
link-aggregate active
!
interface ethernet 4/14
link-aggregate active
!
interface ethernet 4/15
link-aggregate active
!
interface ethernet 4/16
link-aggregate active
Trunk ID: 205
Hw Trunk ID: 1
Ports_Configured: 4
Primary Port Monitored: Jointly
Ports 4/13 4/14 4/15 4/16
Port Names none none none none
Port_Status enable enable enable enable
Monitor off off off off
Rx Mirr Port N/A N/A N/A N/A
Tx Mirr Port N/A N/A N/A N/A
Monitor Dir N/A N/A N/A N/A
Trunk ID: 205
Hw Trunk ID: 1
Duplex: Full
Speed: 1G
Tag: No
Priority: level0
Active Ports: 4
Ports 4/13 4/14 4/15 4/16
Link_Status active active active active
port_state Forward Forward Forward Forward
LACP_Status ready ready ready ready -
Options
EliZ_ Member Posts: 12 ■□□□□□□□□□
BroadcastStorm wrote: »Driver was reinstalled, and other things network was complaining about a hidden drivers when I try to statically set IP address, thanks guys!
It this is still a Issue then use this method, I get it all the time when doing a P2V conversion to vmware all the time:
in a commandprompt(cmd.exe) type these 2 commands:
set devmgr_show_nonpresent_devices=1
start devmgmt.msc
select View/show hidden devices
and remove the old nework card(s).
Remember if you are using Win2k8 you have to start the command prompt as an administrator. -
Options
BroadcastStorm Member Posts: 496
Hi guys, it's a bad network card, please include this on your troubleshooting steps, the card looks like it's working, but upon running diagnostics it shows the flash as bad, on 2 of the network ports. -
Options
BroadcastStorm Member Posts: 496
Not sure why this is in the CCNP forums, but I'm glad you figured it out.
Luv Cisco :P
Etherchannel/LACP