Hyperterminal not executing after hitting enter.

AintRiteAintRite Member Posts: 84 ■■□□□□□□□□
I have searched all over the place for an answer for this. I saw something on this while looking for another problem with hyperterminal last night but when I ran into this problem I couldn't find the information again. So after kinda getting my lab going last night I decided to fool around with one of 1760 routers a little bit (I have absolutely no experience with Cisco besides putting this lad together and very limited networking experience).

So after finally figuring (well searching Google..lol) out how to see what I was typing I think I'm ready to go. Alan2308 on here is kinda mentoring me through this whole beginning process and he gave me a link with some beginning commands. So i finally get to where I can type and I no to the first questions the router asked and hit and.........it goes down a line and nothing....so i hit it again same thing. So i hit it again, same, after working on just getting to this point for 2.5 hours (first router needs some help I guess messed with that for about 45 minutes) i just calmly turned everything off and went to bed.

So to make my very long story short why is the enter button not doing a damn thing besides going to the next line down.
WGU - BS: IT Security...in progress

Comments

  • AintRiteAintRite Member Posts: 84 ■■□□□□□□□□
    Ok so i figure I might as well mess with it this morning while I am waiting for one of you gurus to hopefully help me out. I start looking around for other options and find putty. I down load it and check it out and it says something about using enter to skid a line and using ^m as a command or some thing to that effect (that is what I got out of it anyway). So i go back to ht and mess hit backspace to try and delete something then type in ^m which came up as double text (which I have now fixed) and it starts working. i have no idea why unless this ^m had something to do with it. I'm going to post what I typed so you guys can see it...maybe someone can tell me why it started working.



    Would##h+ hike to enter the initial configuration dialog? [yes/no]: ^^mm



    % Please answer 'yes' or 'no'.

    Would you like to enter the initial configuration dialog? [yes/no]:


    % Please answer 'yes' or 'no'.

    Would you like to enter the initial configuration dialog? [yes/no]: nnoo







    Press RETURN to get started!
    WGU - BS: IT Security...in progress
  • JeanMJeanM Member Posts: 1,117
    Hello, What OS are you using and are you using cisco console cable OR usb-to serial adapter?

    Have you tried downloading Putty or TeraTerm and verified if you get the same results?

    Ok, when it asks you yes/no ...type in a simple "no" and press enter. What do you get then?

    then "enable" and enter
    2015 goals - ccna voice / vmware vcp.
  • AintRiteAintRite Member Posts: 84 ■■□□□□□□□□
    Using Xp professional. i downloaded putty but haven't tried it yet. It seems everything is working fine. here is what I got when I typed in those commands. This is RIGHT after the last part I showed in my second post. The guide I'm using told me to look at the commands when entering a"?". Then I then typed enable and it changed modes like it was supposed too.

    Here is the guide I'm doing right now.

    http://www.jlsnet.co.uk/index.php?page=cc_beginner







    Nov 26 16:23:2EPROTO-5-UPDOWN: Line protocol on Interface Serial1/1, changed sta
    te to down

    Nov 26 16:23:31.623: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEtherne
    t0/0, changed state to up

    Nov 26 16:23:33.070: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEtherne
    t0/0, changed state to down

    Nov 26 16:26:41.002: %SYS-5-RESTART: System restarted --

    Cisco Internetwork Operating System Software

    IOS (tm) C1700 Software (C1700-IPVOICE-M), Version 12.3(26), RELEASE SOFTWARE (f
    c2)

    Technical Support: Support and Documentation - Cisco Systems

    Copyright (c) 1986-2008 by cisco Systems, Inc.

    Compiled Mon 17-Mar-08 14:24 by dchih

    Nov 26 16:26:41.046: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing
    a cold start

    Nov 26 16:26:41.062: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state t
    o administratively down

    Nov 26 16:26:41.062: %LINK-5-CHANGED: Interface Serial0/0, changed state to admi
    nistratively down

    Nov 26 16:26:41.062: %LINK-5-CHANGED: Interface Serial0/1, changed state to admi
    nistratively down

    Nov 26 16:26:41.062: %LINK-5-CHANGED: Interface Serial1/0, changed state to admi
    nistratively down

    Nov 26 16:26:41.062: %LINK-5-CHANGED: Interface Serial1/1, changed state to admi
    nistratively down

    Router>??

    Exec commands:

    access-enable Create a temporary Access-List entry

    access-profile Apply user-profile to interface

    clear Reset functions

    connect Open a terminal connection

    disable Turn off privileged commands

    disconnect Disconnect an existing network connection

    enable Turn on privileged commands

    exit Exit from the EXEC

    help Description of the interactive help system

    lock Lock the terminal

    login Log in as a particular user

    logout Exit from the EXEC

    modemui Start a modem-like user interface

    mrinfo Request neighbor and version information from a multicast

    router

    mstat Show statistics after multiple multicast traceroutes

    mtrace Trace reverse multicast path from destination to source

    name-connection Name an existing network connection

    pad Open a X.29 PAD connection

    ping Send echo messages

    ppp Start IETF Point-to-Point Protocol (PPP)

    resume Resume an active network connection

    rlogin Open an rlogin connection

    show Show running system information

    slip Start Serial-line IP (SLIP)

    - e

    Router>eenablelee


    Router#

    Router#
    WGU - BS: IT Security...in progress
  • JeanMJeanM Member Posts: 1,117
    Sounds like you have ECHO or something on, use putty or teraterm or something, hyperterminal is horrid.
    2015 goals - ccna voice / vmware vcp.
  • Patel128Patel128 Member Posts: 339
    JeanM wrote: »
    Sounds like you have ECHO or something on, use putty or teraterm or something, hyperterminal is horrid.
    Yup i second that. I normally use putty and have never had a problem. Hyperterminal is quite terrible
    Studying For:
    B.S. in Computer Science at University of Memphis
    Network+
    Currently Reading:
    CompTIA Network+ Study Guide - Lammle
  • AintRiteAintRite Member Posts: 84 ■■□□□□□□□□
    I did have echo on, that was the reason for the double text but I had to turn it on at first because I couldn't see any text I was attempting to write. As I said I downloaded putty now to find some documentation on it to figure out how to use it.
    WGU - BS: IT Security...in progress
  • AintRiteAintRite Member Posts: 84 ■■□□□□□□□□
    Ok so now putty is doing the same thing that hyperterminal was doing, with the enter button. I hit the enter button and it just skips a line but doen not run the command I type. This is starting to get frustrating.lol
    WGU - BS: IT Security...in progress
  • georgemcgeorgemc Member Posts: 429
    AintRite wrote: »
    Ok so now putty is doing the same thing that hyperterminal was doing, with the enter button. I hit the enter button and it just skips a line but doen not run the command I type. This is starting to get frustrating.lol

    What exactly is it that you expect the router to do? What output are you expecting from the commands that your are running? Routers tend to sit there and route and not put on flashy displays of their routing prowess

    Commands such as:

    enable
    show version
    show startup-config

    etc., may give you a place to start.

    George
    WGU BS: Business - Information Technology Management
    Start Date: 01 October 2012
    QFT1,PFIT in progress.
    TRANSFERRED/COMPLETED: AGC1,BBC1,LAE1,QBT1,LUT1,QLC1,QMC1,QLT1,IWC1,INC1,INT1,BVC1,CLC1,MGC1, CWV1 BNC1, LIT1,LWC1,QAT1,WFV1,EST1,EGC1,EGT1,IWT1,MKC1,MKT1,RWT1,FNT1,FNC1, BDC1,TPV1 REQUIRED:
  • AintRiteAintRite Member Posts: 84 ■■□□□□□□□□
    I posted a link to the beginners guide in my third post but to answer your question, I would like it to get past the very first command...."no". I just want to know why it doesn't do anything but skip down a line when I hit enter,now.

    The answer to this question....

    Would you like to enter the initial configuration dialog? [yes/no]:

    Just so you don't have to search here is the link to the guide I'm trying to do.
    JLSNet :: Cisco Configs : Beginner Guide to Cisco Router Configuration
    WGU - BS: IT Security...in progress
  • martell1000martell1000 Member Posts: 389
    here is what you could try:

    plug out the console cable
    power up the router, give it some time to boot up
    plug in console cable again
    start terminal programm and try to connect

    some devices sometimes mess up with some usb adapters and produce weird stuff in the console window. this way helped me to work around it a few times ...
    And then, I started a blog ...
  • JeanMJeanM Member Posts: 1,117
    ^ that. Plus also keep in mind to verify serial port settings (baud set on the terminal software you use and the physical device need to match for example). It may not be your problem, but something to check, you could issue "show run" and sometimes a previous person could have set the console port speed to something other than 9600.
    2015 goals - ccna voice / vmware vcp.
  • AintRiteAintRite Member Posts: 84 ■■□□□□□□□□
    I forgot to mention I'm using serial to rj45 console cable. I think it was the way I was powering things up. I haven't had a problem since I last posted . I have started to open up Putty (I dropped hyperterminal) first then power the equipment up. Haven't had a problem since then. I have barley scratched the surface and I am loving the learning so far. Got my Odom's Third Edition in the mail today so I am on my way. I'm sure there will be a ton more stupid posts from me trying to learn so get ready for them.lol

    Thanks for all the replys and I hope some day I will be able to help some on this site like the help I receive. Thanks.
    WGU - BS: IT Security...in progress
  • georgemcgeorgemc Member Posts: 429
    AintRite wrote: »
    I forgot to mention I'm using serial to rj45 console cable. I think it was the way I was powering things up. I haven't had a problem since I last posted . I have started to open up Putty (I dropped hyperterminal) first then power the equipment up. Haven't had a problem since then. I have barley scratched the surface and I am loving the learning so far. Got my Odom's Third Edition in the mail today so I am on my way. I'm sure there will be a ton more stupid posts from me trying to learn so get ready for them.lol

    Thanks for all the replys and I hope some day I will be able to help some on this site like the help I receive. Thanks.

    Good luck in your studies.
    WGU BS: Business - Information Technology Management
    Start Date: 01 October 2012
    QFT1,PFIT in progress.
    TRANSFERRED/COMPLETED: AGC1,BBC1,LAE1,QBT1,LUT1,QLC1,QMC1,QLT1,IWC1,INC1,INT1,BVC1,CLC1,MGC1, CWV1 BNC1, LIT1,LWC1,QAT1,WFV1,EST1,EGC1,EGT1,IWT1,MKC1,MKT1,RWT1,FNT1,FNC1, BDC1,TPV1 REQUIRED:
  • AintRiteAintRite Member Posts: 84 ■■□□□□□□□□
    Thanks, I appreciate it.
    WGU - BS: IT Security...in progress
  • AintRiteAintRite Member Posts: 84 ■■□□□□□□□□
    Ok so now I can't get the router prompt (Router>) on any of my three routers? I am using PuTTY now and everything worked fine until yesterday morning. I was using it 8 hours before that. It will go through the boot process but then at the end the router prompt is missing. Anyone have any ideas what is happening. I'm guessing this is a router problem and not PuTTY. I have searched all over the net but have found nothing on this kind of thing.
    WGU - BS: IT Security...in progress
  • MAC_AddyMAC_Addy Member Posts: 1,740 ■■■■□□□□□□
    What happens when you open putty and hit enter a few times?
    2017 Certification Goals:
    CCNP R/S
  • Timber WolfTimber Wolf Member Posts: 90 ■■□□□□□□□□
    You may have a bad console cable. I have ran into issues similar to yours and that turned out to be the case. Have you tried swapping the one that you are using now with another one?
    WGU BS IT - Security
    Need to complete: CSV1 BOV1 RIT1 BNC1 KET1 TPV1 MGC1 CJV1 KFT1 CNV1 SBT1 RGT1
    Completed: CUV1 CTV1
    Transferred: CVV1 DJV1 IWT1 IWC1 BVC1 QLT1 DHV1 HHT1 GAC1 DFV1 INT1 INC1 CPV1 AXV1 QBT1 LUT1 LAE1 CLC1 BBC1 AGC1 WFV1 CQV1 COV1
  • AintRiteAintRite Member Posts: 84 ■■□□□□□□□□
    LOL...I have not and I have about 8 brand new ones. That should have been the first I should have done. I have switched computers even but not cables.
    WGU - BS: IT Security...in progress
  • AintRiteAintRite Member Posts: 84 ■■□□□□□□□□
    NICE!!!! That worked. That first cable didn't last that long. Only used it four or five times. I hate when I over look the simple things that should be tried first, I'll now crawl back under the rock I was hiding.
    WGU - BS: IT Security...in progress
  • JeanMJeanM Member Posts: 1,117
    Nice! Well, that was easy :)
    2015 goals - ccna voice / vmware vcp.
Sign In or Register to comment.