EIGRP Not working

markulousmarkulous Member Posts: 2,394 ■■■■■■■■□□
So I'm going through Jeremy's CBT Nuggets videos for the CCNA. Just got the EIGRP config. Seems like it is super easy to setup. All he did was go into global config mode, go to rou eigrp 1, and advertise the network on that router and EIGRP was working fine for him in GNS3. I did that on both routers, yet when I go to sh ip eigrp neigh it doesn't show anything. Everything on my network pings each other just fine. I attached my topo.

Comments

  • no!all!no!all! Member Posts: 245 ■■■□□□□□□□
    Does a sh ip route give you any routes known by EIGRP? Have you tried any debugging?
    A+, N+, S+, CCNA:RS, CCNA:Sec

    "In high society TCP is more welcome than UDP. At least it knows a proper handshake" - Ben Franklin

    2019 Goals: CCNP:RS & relocate to St. Pete, FL!
  • networker050184networker050184 Mod Posts: 11,962 Mod
    What's the config look like? Interface and EIGRP.
    An expert is a man who has made all the mistakes which can be made.
  • HeeroHeero Member Posts: 486
    Maybe provide configs?
  • Jon_CiscoJon_Cisco Member Posts: 1,772 ■■■■■■■■□□
    I never really used the PT-Cloud so I don't know it's setup but maybe it does not support eigrp?
    Is the layer 3 switch routing the vlans? What are you trying to accomplish with the eigrp?
  • Dieg0MDieg0M Member Posts: 861
    ip routing on L3 switch?
    Follow my CCDE journey at www.routingnull0.com
  • markulousmarkulous Member Posts: 2,394 ■■■■■■■■□□
    no!all! wrote: »
    Does a sh ip route give you any routes known by EIGRP? Have you tried any debugging?

    It only shows connected routes and a static route I put in for 0.0.0.0. I forgot to mention that.

    Hmm...now that I did the debug, for some reason ROUTER0 is not sending Hellos to SWOUTER0, only to the serial interface.
  • markulousmarkulous Member Posts: 2,394 ■■■■■■■■□□
    Dieg0M wrote: »
    ip routing on L3 switch?

    Yes that is enabled. It routes packets through vlans just fine.
  • Dieg0MDieg0M Member Posts: 861
    send configs or we will be guessing all day
    Follow my CCDE journey at www.routingnull0.com
  • markulousmarkulous Member Posts: 2,394 ■■■■■■■■□□
    What's the config look like? Interface and EIGRP.

    Interface from ROUTER0:

    GigabitEthernet0/0 is up, line protocol is up (connected)
    Hardware is CN Gigabit Ethernet, address is 000a.f3b5.a501 (bia 000a.f3b5.a501)
    Internet address is 10.1.1.6/30
    MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation ARPA, loopback not set
    Keepalive set (10 sec)
    Full-duplex, 100Mb/s, media type is RJ45
    output flow-control is unsupported, input flow-control is unsupported
    ARP type: ARPA, ARP Timeout 04:00:00,
    Last input 00:00:08, output 00:00:05, output hang never
    Last clearing of "show interface" counters never
    Input queue: 0/75/0 (size/max/drops); Total output drops: 0
    Queueing strategy: fifo
    Output queue :0/40 (size/max)
    5 minute input rate 104 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    111 packets input, 6660 bytes, 0 no buffer
    Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 watchdog, 1017 multicast, 0 pause input
    0 input packets with dribble condition detected
    0 packets output, 0 bytes, 0 underruns
    0 output errors, 0 collisions, 1 interface resets
    0 unknown protocol drops
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier
    0 output buffer failures, 0 output buffers swapped out

    Sh EIGRP inter for ROUTER0:

    IP-EIGRP interfaces for process 1

    Xmit Queue Mean Pacing Time Multicast Pending
    Interface Peers Un/Reliable SRTT Un/Reliable Flow Timer Routes
    Se0/3/0 0 0/0 1236 0/10 0 0

    Doesn't look like it wants to communicate through Gig 0/0 so SWOUTER0 is sending hello messages there and ROUTER0 is just ignoring them and not sending anything back. I disabled passive-interface on everything and Gig 0/0 specifcally but no change.
  • markulousmarkulous Member Posts: 2,394 ■■■■■■■■□□
    Sh interfaces from SWOUTER0:

    GigabitEthernet0/2 is up, line protocol is up (connected)
    Hardware is Lance, address is 0001.63a4.261a (bia 0001.63a4.261a)
    MTU 1500 bytes, BW 1000000 Kbit, DLY 1000 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation ARPA, loopback not set
    Keepalive set (10 sec)
    Full-duplex, 1000Mb/s
    input flow-control is off, output flow-control is off
    ARP type: ARPA, ARP Timeout 04:00:00
    Last input 00:00:08, output 00:00:05, output hang never
    Last clearing of "show interface" counters never
    Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
    Queueing strategy: fifo
    Output queue :0/40 (size/max)
    5 minute input rate 0 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    956 packets input, 193351 bytes, 0 no buffer
    Received 956 broadcasts, 0 runts, 0 giants, 0 throttles
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 watchdog, 0 multicast, 0 pause input
    0 input packets with dribble condition detected
    2357 packets output, 263570 bytes, 0 underruns
    0 output errors, 0 collisions, 10 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier
    0 output buffer failures, 0 output buffers swapped out

    Sh ip eigrp interfaces from SWOUTER0:
    IP-EIGRP interfaces for process 1

    Xmit Queue Mean Pacing Time Multicast Pending
    Interface Peers Un/Reliable SRTT Un/Reliable Flow Timer Routes
    Fa0/1 0 0/0 1236 0/10 0 0
    Gig0/2 0 0/0 1236 0/10 0 0
    Vlan 0 0/0 1236 0/10 0 0
    Vlan 0 0/0 1236 0/10 0 0
  • Dieg0MDieg0M Member Posts: 861
    That is not what I asked for. Please post the config.
    Follow my CCDE journey at www.routingnull0.com
  • markulousmarkulous Member Posts: 2,394 ■■■■■■■■□□
    Dieg0M wrote: »
    That is not what I asked for. Please post the config.

    I was replying to someone else...

    Here is running-config on ROUTER0

    Current configuration : 1159 bytes
    !
    version 15.1
    no service timestamps log datetime msec
    no service timestamps debug datetime msec
    no service password-encryption
    !
    hostname Router
    !
    !
    !
    enable secret 5 $1$mERr$hx5rVt7rPNoS4wqbXKX7m0
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    license udi pid CISCO2911/K9 sn FTX1524HPWG
    !
    !
    !
    !
    !
    spanning-tree mode pvst
    !
    !
    !
    !
    interface GigabitEthernet0/0
    ip address 10.1.1.6 255.255.255.252
    duplex auto
    speed auto
    !
    interface GigabitEthernet0/1
    no ip address
    duplex auto
    speed auto
    shutdown
    !
    interface GigabitEthernet0/2
    no ip address
    duplex auto
    speed auto
    shutdown
    !
    interface Serial0/3/0
    ip address 80.23.1.1 255.255.255.252
    encapsulation frame-relay
    frame-relay interface-dlci 100
    !
    interface Serial0/3/1
    no ip address
    shutdown
    !
    interface Vlan1
    no ip address
    shutdown
    !
    interface Vlan10
    no ip address
    !
    interface Vlan20
    no ip address
    !
    router eigrp 1
    network 80.0.0.0
    auto-summary
    !
    ip classless
    ip route 10.1.0.0 255.255.0.0 10.1.1.5
    ip route 0.0.0.0 0.0.0.0 80.23.1.2
    !
    !
    !
    banner login ^C
    ******************
    LOL U WISH
    ******************^C
    !
    !
    !
    !
    line con 0
    password cisco
    login
    !
    line aux 0
    !
    line vty 0 4
    login
    line vty 5 15
    login
    !
    !
    !
    end

    Running Config on SWOUTER0

    Current configuration : 1650 bytes
    !
    version 12.2
    no service timestamps log datetime msec
    no service timestamps debug datetime msec
    no service password-encryption
    !
    hostname SWOUTER0
    !
    !
    !
    enable secret 5 $1$mERr$hx5rVt7rPNoS4wqbXKX7m0
    !
    !
    !
    ip routing
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    spanning-tree mode pvst
    !
    !
    !
    !
    interface FastEthernet0/1
    no switchport
    ip address 10.1.1.2 255.255.255.252
    ip helper-address 10.1.1.1
    duplex auto
    speed auto
    !
    interface FastEthernet0/2
    !
    interface FastEthernet0/3
    !
    interface FastEthernet0/4
    !
    interface FastEthernet0/5
    !
    interface FastEthernet0/6
    !
    interface FastEthernet0/7
    !
    interface FastEthernet0/8
    !
    interface FastEthernet0/9
    !
    interface FastEthernet0/10
    !
    interface FastEthernet0/11
    !
    interface FastEthernet0/12
    !
    interface FastEthernet0/13
    !
    interface FastEthernet0/14
    !
    interface FastEthernet0/15
    !
    interface FastEthernet0/16
    !
    interface FastEthernet0/17
    !
    interface FastEthernet0/18
    !
    interface FastEthernet0/19
    !
    interface FastEthernet0/20
    !
    interface FastEthernet0/21
    !
    interface FastEthernet0/22
    !
    interface FastEthernet0/23
    !
    interface FastEthernet0/24
    !
    interface GigabitEthernet0/1
    switchport trunk encapsulation dot1q
    switchport mode trunk
    !
    interface GigabitEthernet0/2
    no switchport
    ip address 10.1.1.5 255.255.255.252
    duplex auto
    speed auto
    !
    interface Vlan1
    no ip address
    !
    interface Vlan10
    ip address 10.1.2.1 255.255.255.0
    ip helper-address 10.1.1.1
    !
    interface Vlan20
    ip address 10.1.3.1 255.255.255.0
    ip helper-address 10.1.1.1
    !
    router eigrp 1
    network 10.0.0.0
    auto-summary
    !
    ip classless
    ip route 0.0.0.0 0.0.0.0 10.1.1.6
    !
    !
    !
    !
    !
    !
    !
    line con 0
    password cisco
    login
    !
    line aux 0
    !
    line vty 0 4
    login
    !
    !
    !
    end
  • Dieg0MDieg0M Member Posts: 861
    ROUTER0:
    router eigrp 1
    network 10.0.0.0

    In IGP's the network command does not advertise a network but indicates at the router what interface matching that subnet should be using the IGP (and advertising hello's for neighborship)
    Follow my CCDE journey at www.routingnull0.com
  • markulousmarkulous Member Posts: 2,394 ■■■■■■■■□□
    Jon_Cisco wrote: »
    I never really used the PT-Cloud so I don't know it's setup but maybe it does not support eigrp?
    Is the layer 3 switch routing the vlans? What are you trying to accomplish with the eigrp?

    I have no idea if it does or not. I was just using that to setup frame relay.

    Yes, the L3 switch is routing the Vlans.

    I am just trying to experiment with it so it'll advertise routes. I'm just following along with CBT Nuggets anytime they configure something.
  • markulousmarkulous Member Posts: 2,394 ■■■■■■■■□□
    Dieg0M wrote: »
    ROUTER0:
    router eigrp 1
    network 10.0.0.0

    That just formed the adjacency. I was advertising that route on SWOUTER0, why do I have to advertise it again on ROUTER0? Or am I misinterpreting the command?
  • markulousmarkulous Member Posts: 2,394 ■■■■■■■■□□
    Dieg0M wrote: »

    In IGP's the network command does not advertise a network but indicates at the router what interface matching that subnet should be using the IGP (and advertising hello's for neighborship)

    Ah...ok so every time I do the network command on one interface, I need to do it on the corresponding interface to form the adjacency. So I see this working best in a large environment where a lot of routes have to be summarized.
  • HondabuffHondabuff Member Posts: 667 ■■■□□□□□□□
    When you use EIGRP, first step is to use after the Router eigrp XXX command is "no auto summary" command. If not you can have 2 branch routers advertising the same routes because summarization is on by default. You should also get in the habit of using the subnet mask for your route advertisements. "network 10.1.1.0 255.255.255.252"
    “The problem with quotes on the Internet is that you can’t always be sure of their authenticity.” ~Abraham Lincoln
Sign In or Register to comment.