Lc-atm

adriansizemoreadriansizemore Member Posts: 51 ■■□□□□□□□□
I am unable to get an LC-ATM interface to work on my 7200 in my lab. Ive attached a picture of my lab to this post:
mplsvrfatmlab.JPG

The edge atm router is SanDiego and Raleigh. The LSR is Denver.

Configs for SanDiego:

interface ATM1/0
no ip address
no atm auto-configuration
no atm ilmi-keepalive
no atm address-registration
!
interface ATM1/0.101 mpls
ip address 192.168.12.1 255.255.255.252
pvc 0/101

Configs for Denver:

interface ATM2/0
no ip address
no atm auto-configuration
no atm ilmi-keepalive
no atm address-registration
!
interface ATM1/0.100 mpls
ip address 192.168.12.2 255.255.255.252
pvc 0/100

I am at work right now, but if you have any config advice, please let me know until I can get some MPLS show commands and/or debug output.
10 years Military (6 as data tech)
A.A.S Telecom/Network Technologies
CCNA
642-611
Backbone Engineer

Comments

  • mikej412mikej412 Member Posts: 10,090
    What IOS Version? Support for LC-ATM was removed in 12.4(20)T

    Is this real equipment or dynamips?
    :mike: Cisco Certifications -- Collect the Entire Set!
  • adriansizemoreadriansizemore Member Posts: 51 ■■□□□□□□□□
    Yeah, that will do it:


    BOOTLDR: 7200 Software (C7200-ADVIPSERVICESK9-M), Version 12.4(2)T, RELEASE SOFT WARE (fc1)



    an i am using dynamips, which I will say, has been extremely helpful. I have been able to do any lab for my 642-611 thus far; well, with the exception of lc-atm.
    10 years Military (6 as data tech)
    A.A.S Telecom/Network Technologies
    CCNA
    642-611
    Backbone Engineer
  • APAAPA Member Posts: 959
    Correct me if I'm wrong but in this situation couldn't you use AToM for ATMoverMPLS?

    xconnect on the ATM switch interfaces to allow for a L2VPN over the MPLS core?

    CCNA | CCNA:Security | CCNP | CCIP
    JNCIA:JUNOS | JNCIA:EX | JNCIS:ENT | JNCIS:SEC
    JNCIS:SP | JNCIP:SP
  • adriansizemoreadriansizemore Member Posts: 51 ■■□□□□□□□□
    A.P.A wrote: »
    Correct me if I'm wrong but in this situation couldn't you use AToM for ATMoverMPLS?

    xconnect on the ATM switch interfaces to allow for a L2VPN over the MPLS core?


    I kind of wanted to stay on track with the book, besides, I dont know how to do that
    10 years Military (6 as data tech)
    A.A.S Telecom/Network Technologies
    CCNA
    642-611
    Backbone Engineer
  • APAAPA Member Posts: 959
    the legacy command that implemented the same L2VPN for ATOM was previously

    mpls l2transport {etc}

    which they conveniently changed to

    xconnect {etc}

    My knowledge of MPLS is only limited at the moment and I've only seen it in effect at the new company I currently work at. But this is how we used EoMPLS(Ethernet over MPLS) to extend an IPTV VLAN over a L2VPN from one side of the country to the other across our MPLS core.

    Check it out here

    L2VPN Interworking  [Cisco IOS and NX-OS Software] - Cisco Systems

    Hmmz.... however now that I look at the compatible transports I don't see ATM to ATM...... Only ATM to Ethernet, ATM to Frame-Relay.

    CCNA | CCNA:Security | CCNP | CCIP
    JNCIA:JUNOS | JNCIA:EX | JNCIS:ENT | JNCIS:SEC
    JNCIS:SP | JNCIP:SP
Sign In or Register to comment.