2 switches 1 router

Hi guys, i'm trying to run 2 switches (2960 POE and other non POE) with 2 differents IP on 1 router (cisco 2811).
One is basically only for 7911 phones and the other for CIPC connected to PCs with DHCP from a network router, but I cannot make each nets to ping themselves. Thanks in advance for your feedback

Attached you can find my run

show run
Building configuration...

Current configuration : 8949 bytes
!
! Last configuration change at 15:47:35 utc Tue Oct 4 2016
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname CUCMTCF
!
boot-start-marker
boot-end-marker
!
card type e1 0 0
no logging buffered
no logging console
enable secret 5 $1$0iXf$9YERhi2mGp2fwSODl4CzK1
!
no aaa new-model
clock timezone utc -6
network-clock-participate wic 0
network-clock-select 1 E1 0/0/0
!
!
!
ip cef
no ip dhcp use vrf connected
!
ip dhcp pool Voice
network 10.110.17.0 255.255.255.0
default-router 10.110.17.1
option 150 ip 10.110.17.1
!
ip dhcp pool Data
network 192.168.10.0 255.255.255.0
default-router 192.168.10.2
option 200 ip 192.168.10.200
option 150 ip 192.168.10.200
!
!
no ip domain lookup
multilink bundle-name authenticated
!
isdn switch-type primary-ni
!
!
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
h323
!
!
voice class codec 1
codec preference 1 g729r8
codec preference 2 g711ulaw
codec preference 3 g711alaw
codec preference 4 g729br8
!
!
!
voice class h323 1
h225 timeout tcp establish 3
!
!
!
!
!
!
!
!
!
!
voice translation-rule 1
rule 1 // // type unknown national plan isdn isdn
!
voice translation-rule 2
rule 1 /^9/ // type any national plan any isdn
!
voice translation-rule 10
rule 1 // // type unknown national plan isdn isdn
!
!
voice translation-profile PSTN
translate called 1
!
voice translation-profile int
translate called 14
!
voice translation-profile isdn_map
translate called 10
!
!
voice-card 0
dspfarm
dsp services dspfarm
!
!
!
!
!
archive
log config
hidekeys
!
!
controller E1 0/0/0
framing NO-CRC4
pri-group timeslots 1-10,16
!
!
!
!
!
interface FastEthernet0/0
description DATOS
ip address 192.168.10.200 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/0.1
description *** Data vlan ***
encapsulation dot1Q 1 native
ip address 10.110.7.40 255.255.255.0
!
interface FastEthernet0/0.2
description *** Voice vlan ***
encapsulation dot1Q 2
!
interface FastEthernet0/1
ip address 10.110.17.1 255.255.255.0
duplex auto
speed auto
h323-gateway voip interface
h323-gateway voip bind srcaddr 10.110.17.1
!
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-5ess
isdn incoming-voice voice
no cdp enable
interface Serial0/1/0
no ip address
shutdown
no fair-queue
clock rate 2000000
!
interface Serial0/1/1
no ip address
shutdown
clock rate 2000000
!
ip route 0.0.0.0 0.0.0.0 192.168.10.1
!
!
ip http server
no ip http secure-server
!
access-list 1 permit 192.168.10.1
access-list 101 permit ip any any
!
!
!
control-plane
!
!
!
voice-port 0/0/0:15
bearer-cap Speech
!
voice-port 0/2/0
timing hookflash-out 50
!
voice-port 0/2/1
!
voice-port 0/2/2
!
voice-port 0/2/3
!
voice-port 0/3/0
!
voice-port 0/3/1
!
voice-port 0/3/2
!
voice-port 0/3/3
!
!
!

!
!
sccp local FastEthernet0/1
sccp ccm 10.110.17.1 identifier 1
sccp
!
sccp ccm group 1
associate ccm 1 priority 1
associate profile 1 register mtp001cf685c3e9
keepalive retries 5
switchover method immediate
switchback interval 5
!
dspfarm profile 1 transcode
codec g711ulaw
codec g711alaw
codec ilbc
codec g723r63
codec g723r53
codec gsmamr-nb
codec g729ar8
codec g729abr8
maximum sessions 3
associate application SCCP
!
dial-peer cor custom
!
!
!
dial-peer voice 1 pots
tone ringback alert-no-PI
translation-profile outgoing isdn_map
destination-pattern 0T
incoming called-number .
direct-inward-dial
port 0/0/0:15
forward-digits all
!
dial-peer voice 1000 voip
preference 2
destination-pattern 0.T
voice-class codec 1
session target ipv4:10.110.17.1
dtmf-relay h245-alphanumeric
!
dial-peer voice 1005 voip
description llamadas Salientes Paises
destination-pattern 5T
voice-class codec 1
session target ipv4:10.110.17.1
!
dial-peer voice 1002 voip
description salientes old
destination-pattern 2...
voice-class codec 1
session target ipv4:10.110.17.1
dtmf-relay h245-alphanumeric
!
dial-peer voice 3 voip
!
dial-peer voice 15500 pots
translation-profile outgoing int
destination-pattern 9T
port 0/0/0:15
!
dial-peer voice 1007 voip
!
!
num-exp 66261902 1902
num-exp 66261903 1903
num-exp 66261904 1904
num-exp 66261905 1905
num-exp 66261906 1906
num-exp 66261907 1907
num-exp 66261908 1908
num-exp 66261909 1909
num-exp 66261910 1910
num-exp 66261911 1911
num-exp 66261912 1912
num-exp 66261940 1940
num-exp 66261920 1920
num-exp 66261921 1921
num-exp 66261922 1922
num-exp 66261926 1926
num-exp 66261917 1917
num-exp 66261918 1918
num-exp 66261913 1913
num-exp 66261900 1900
num-exp 66261915 1915
num-exp 66261919 1919
gateway
timer receive-rtp 1200
!
!
telephony-service
sdspfarm units 5
sdspfarm transcode sessions 128
no auto-reg-ephone
max-ephones 40
max-dn 130
ip source-address 10.110.17.1 port 2000
timeouts interdigit 4
system message (TCF) BIT GUATEMALA
max-conferences 8 gain -6
transfer-system full-consult
create cnf-files version-stamp 7960 Oct 04 2016 13:55:22

Find more posts tagged with

Comments

Mr.Network

are you pinging from the switches? if so are the Default gateway configured?

fer_nandillo

Mr.Network wrote: »

are you pinging from the switches? if so are the Default gateway configured?

Hi, this should be the diagram

I can ping from my 10.110.17.1 IP switch but I cannot ping from my 192.168.10.1 switch, which is connected to a WAN Router.

Attached you can find my topology

guestaccess.aspx?guestaccesstoken=zd1CruBknVhtFFMxMnOrwAjwNX5Jr4nHgqgGP5RubTc%3d&docid=07e8c528372b64fe69599d9bee6a55d06&rev=1&expiration=2016-11-05T19%3a12%3a24.000Z

guestaccess.aspx?guestaccesstoken=zd1CruBknVhtFFMxMnOrwAjwNX5Jr4nHgqgGP5RubTc%3d&docid=07e8c528372b64fe69599d9bee6a55d06&rev=1&expiration=2016-11-05T19%3a12%3a24.000Z

Thanks

hodgey87

Hi @fer_nandillo

Could you upload the packet tracer file at all?

Mr.Network

is the 192.168.10.1 mngmt ip of the switch 1 or is the gateway of wan router?

can you post the config of the Switch2 and Router1?

varelg

So the DHCP on the router is the one assigning IP address to the second switch. Who assigns IP's to the first switch? Of course you can't ping the one from the other, 10.x.x.x and 192.x.x.x both are different networks.

fer_nandillo

Mr.Network wrote: »

is the 192.168.10.1 mngmt ip of the switch 1 or is the gateway of wan router?

can you post the config of the Switch2 and Router1?

Hi, 192.168.10.1 is the LAN default GW of the router who assigns DHCP to my PCs.

My main requirement is to have SW0 with 7911s phones and SW1 with PCs and CIPCs installed.

All I get is my softphones displaying Registering and then Defaulting to TFTP Server

Thanks

fer_nandillo

varelg wrote: »

So the DHCP on the router is the one assigning IP address to the second switch. Who assigns IP's to the first switch? Of course you can't ping the one from the other, 10.x.x.x and 192.x.x.x both are different networks.

Hi: SW0:10.x.x.x is only for POE Cisco phones

SW1: 192.x.x.x is for accessing internet through the computers and installing cisco Sofphones, my issue is that i cannot make the Cisco Softphones reachs the router and register for making calls,

Thanks

Thanks

varelg

You will either need to introduce a bridge between two networks or force router0 to act as a bridge between the two networks. As it is now, those phones and those PC host can't see each other nor share internet connection because they are on two different networks.

DCD

You need a routing protocol or static route back to the 10 network. Normally you don't put a IP address on the main interface if you are using sub-interfaces. And as it was said before add a link to the PT file.

fer_nandillo

Hi, if this can't be done easily, I'll choose to only connect my router to my 192.x.x.x net.

Which means only softphones.

Should I connect my fa0/0 interface to my 2960 switch or directly to my ethernet ports from my ISP router?

Thanks

hodgey87

Have you listened to the advice from @DCD?

Please share the file or at least more of the configurations.

fer_nandillo

Hi all...

I don't have a PT file...this is a real life issue

The PT diagram was just for guide purposes

Regards

DCD

Then we need the running configuration from both switches and the other router. But the best thing to do is redesign the network.

fer_nandillo

DCD wrote: »

Then we need the running configuration from both switches and the other router. But the best thing to do is redesign the network.

Hi DCD, this was solved...bad ethernet cable.

Thanks to all for your help!