Dial-peers via T1 crossover

Hi,
Trying to connect two analogue phone sets via T1 crossover cable but so far no luck. Any help to find a solution will be much appreciated.
Thanks
Topology:
Phone x1111

fxs-(R1)-T1

crossover T1

T1-(R2)-fxs

x2222 Phone
Home made T1 cross over cable
1 – 4
2 – 5
4 – 1
5 – 2
Almost same config on Router 2 (R2_3725) except clock source for T1 is set to Line
R1_3640#sh run
controller T1 1/0
framing esf
clock source internal
linecode b8zs
ds0-group 0 timeslots 1-8 type fxo-loop-start
ds0-group 1 timeslots 9-16 type e&m-wink-start
!
voice-port 1/0:0
output attenuation 0
voice-port 1/0:1
voice-port 3/0/0
voice-port 3/0/1
voice-port 3/1/0
voice-port 3/1/1
!
dial-peer voice 1111 pots
destination-pattern 1111
port 3/0/0
!
dial-peer voice 1000 pots
destination-pattern 2222
port 1/0:0
forward-digits all

R1_3640#sh voice port sum
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
============== == ============ ===== ==== ======== ======== ==
1/0:0 01 fxo-ls up dorm idle on-hook y
1/0:0 02 fxo-ls up dorm idle on-hook y
1/0:0 03 fxo-ls up dorm idle on-hook y
1/0:0 04 fxo-ls up dorm idle on-hook y
1/0:0 05 fxo-ls up dorm idle on-hook y
1/0:0 06 fxo-ls up dorm idle on-hook y
1/0:0 07 fxo-ls up dorm idle on-hook y
1/0:0 08 fxo-ls up dorm idle on-hook y
1/0:1 09 e&m-wnk up dorm idle idle y
1/0:1 10 e&m-wnk up dorm idle idle y
1/0:1 11 e&m-wnk up dorm idle idle y
1/0:1 12 e&m-wnk up dorm idle idle y
1/0:1 13 e&m-wnk up dorm idle idle y
1/0:1 14 e&m-wnk up dorm idle idle y
1/0:1 15 e&m-wnk up dorm idle idle y
1/0:1 16 e&m-wnk up dorm idle idle y
3/0/0 -- fxs-ls up dorm on-hook idle y
3/0/1 -- fxs-ls up dorm on-hook idle y
3/1/0 -- fxo-ls up dorm idle on-hook y
3/1/1 -- fxo-ls up dorm idle on-hook y

R1_3640#sh controllers t1 1/0
T1 1/0 is up.
Applique type is Channelized T1
Cablelength is long gain36 0db
No alarms detected.
alarm-trigger is not set
Soaking time: 3, Clearance time: 10
AIS State:Clear LOS State:Clear LOF State:Clear
Version info Firmware: 20051006, FPGA: 20, spm_count = 0
Framing is ESF, Line Code is B8ZS, Clock Source is Internal.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (729 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 1:
4 Line Code Violations, 9798 Path Code Violations
4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
4 Errored Secs, 0 Bursty Err Secs, 4 Severely Err Secs, 501 Unavail Secs
Total Data (last 1 15 minute intervals):
4 Line Code Violations, 9798 Path Code Violations,
4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
4 Errored Secs, 0 Bursty Err Secs, 4 Severely Err Secs, 501 Unavail Secs

Find more posts tagged with

Comments

nice343

check the voice config on the 1000 dial peer.

it should be

dial-peer voice 1000 voip
destination-pattern 2222
session target ipv4:192.168.1.1

assuming 192.168.1.1 is the ip address of the remote router

nagen

nice343 wrote:
check the voice config on the 1000 dial peer.

it should be
dial-peer voice 1000 voip
destination-pattern 2222
session target ipv4:192.168.1.1
assuming 192.168.1.1 is the ip address of the remote router

Thanks for your reply,
but I am trying to simulate PSTN, trying to route call through digital T1 CAS.
It should be pots and ports based. I don't think there is a need of IP address cause IP WAN is broken in this scenario.

Luckycharms

As for what is not exactly working I don't know, primarily because I don't know the problems...Is it one way calling?? are you even seeing the call legs being established?

I would also look into timing on you T1.... Looks like you might be having problems.

4 Line Code Violations, 9798 Path Code Violations
4 Errored Secs, 0 Bursty Err Secs, 4 Severely Err Secs, 501 Unavail Secs

nagen

Luckycharms wrote:

As for what is not exactly working I don't know, primarily because I don't know the problems...Is it one way calling?? are you even seeing the call legs being established?

I would also look into timing on you T1.... Looks like you might be having problems.

4 Line Code Violations, 9798 Path Code Violations
4 Errored Secs, 0 Bursty Err Secs, 4 Severely Err Secs, 501 Unavail Secs

Well it's a two way calling, I cleared the error log counter, so there is no more error and interface is in up state but still no calls going through.

tech-airman

nagen,

nagen wrote:

Hi,
Trying to connect two analogue phone sets via T1 crossover cable but so far no luck. Any help to find a solution will be much appreciated.
Thanks

Have you verified that you're getting a dialtone on both of your phones?

nagen wrote:

Topology:
Phone x1111
fxs-(R1)-T1
crossover T1
T1-(R2)-fxs
x2222 Phone
Home made T1 cross over cable
1 – 4
2 – 5
4 – 1
5 – 2
Almost same config on Router 2 (R2_3725) except clock source for T1 is set to Line
R1_3640#sh run
controller T1 1/0
framing esf
clock source internal
linecode b8zs
ds0-group 0 timeslots 1-8 type fxo-loop-start
ds0-group 1 timeslots 9-16 type e&m-wink-start
!
voice-port 1/0:0
output attenuation 0
voice-port 1/0:1
voice-port 3/0/0
voice-port 3/0/1
voice-port 3/1/0
voice-port 3/1/1
!
dial-peer voice 1111 pots
destination-pattern 1111
port 3/0/0
!
dial-peer voice 1000 pots
destination-pattern 2222
port 1/0:0
forward-digits all

R1_3640#sh voice port sum
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
============== == ============ ===== ==== ======== ======== ==
1/0:0 01 fxo-ls up dorm idle on-hook y
1/0:0 02 fxo-ls up dorm idle on-hook y
1/0:0 03 fxo-ls up dorm idle on-hook y
1/0:0 04 fxo-ls up dorm idle on-hook y
1/0:0 05 fxo-ls up dorm idle on-hook y
1/0:0 06 fxo-ls up dorm idle on-hook y
1/0:0 07 fxo-ls up dorm idle on-hook y
1/0:0 08 fxo-ls up dorm idle on-hook y
1/0:1 09 e&m-wnk up dorm idle idle y
1/0:1 10 e&m-wnk up dorm idle idle y
1/0:1 11 e&m-wnk up dorm idle idle y
1/0:1 12 e&m-wnk up dorm idle idle y
1/0:1 13 e&m-wnk up dorm idle idle y
1/0:1 14 e&m-wnk up dorm idle idle y
1/0:1 15 e&m-wnk up dorm idle idle y
1/0:1 16 e&m-wnk up dorm idle idle y
3/0/0 -- fxs-ls up dorm on-hook idle y
3/0/1 -- fxs-ls up dorm on-hook idle y
3/1/0 -- fxo-ls up dorm idle on-hook y
3/1/1 -- fxo-ls up dorm idle on-hook y

R1_3640#sh controllers t1 1/0
T1 1/0 is up.
Applique type is Channelized T1
Cablelength is long gain36 0db
No alarms detected.
alarm-trigger is not set
Soaking time: 3, Clearance time: 10
AIS State:Clear LOS State:Clear LOF State:Clear
Version info Firmware: 20051006, FPGA: 20, spm_count = 0
Framing is ESF, Line Code is B8ZS, Clock Source is Internal.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (729 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 1:
4 Line Code Violations, 9798 Path Code Violations
4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
4 Errored Secs, 0 Bursty Err Secs, 4 Severely Err Secs, 501 Unavail Secs
Total Data (last 1 15 minute intervals):
4 Line Code Violations, 9798 Path Code Violations,
4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
4 Errored Secs, 0 Bursty Err Secs, 4 Severely Err Secs, 501 Unavail Secs

nagen

tech-airman wrote:

nagen,

nagen wrote:

Hi,
Trying to connect two analogue phone sets via T1 crossover cable but so far no luck. Any help to find a solution will be much appreciated.
Thanks

Have you verified that you're getting a dialtone on both of your phones?

nagen wrote:

Topology:
Phone x1111
fxs-(R1)-T1
crossover T1
T1-(R2)-fxs
x2222 Phone
Home made T1 cross over cable
1 – 4
2 – 5
4 – 1
5 – 2
Almost same config on Router 2 (R2_3725) except clock source for T1 is set to Line
R1_3640#sh run
controller T1 1/0
framing esf
clock source internal
linecode b8zs
ds0-group 0 timeslots 1-8 type fxo-loop-start
ds0-group 1 timeslots 9-16 type e&m-wink-start
!
voice-port 1/0:0
output attenuation 0
voice-port 1/0:1
voice-port 3/0/0
voice-port 3/0/1
voice-port 3/1/0
voice-port 3/1/1
!
dial-peer voice 1111 pots
destination-pattern 1111
port 3/0/0
!
dial-peer voice 1000 pots
destination-pattern 2222
port 1/0:0
forward-digits all

R1_3640#sh voice port sum
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
============== == ============ ===== ==== ======== ======== ==
1/0:0 01 fxo-ls up dorm idle on-hook y
1/0:0 02 fxo-ls up dorm idle on-hook y
1/0:0 03 fxo-ls up dorm idle on-hook y
1/0:0 04 fxo-ls up dorm idle on-hook y
1/0:0 05 fxo-ls up dorm idle on-hook y
1/0:0 06 fxo-ls up dorm idle on-hook y
1/0:0 07 fxo-ls up dorm idle on-hook y
1/0:0 08 fxo-ls up dorm idle on-hook y
1/0:1 09 e&m-wnk up dorm idle idle y
1/0:1 10 e&m-wnk up dorm idle idle y
1/0:1 11 e&m-wnk up dorm idle idle y
1/0:1 12 e&m-wnk up dorm idle idle y
1/0:1 13 e&m-wnk up dorm idle idle y
1/0:1 14 e&m-wnk up dorm idle idle y
1/0:1 15 e&m-wnk up dorm idle idle y
1/0:1 16 e&m-wnk up dorm idle idle y
3/0/0 -- fxs-ls up dorm on-hook idle y
3/0/1 -- fxs-ls up dorm on-hook idle y
3/1/0 -- fxo-ls up dorm idle on-hook y
3/1/1 -- fxo-ls up dorm idle on-hook y

R1_3640#sh controllers t1 1/0
T1 1/0 is up.
Applique type is Channelized T1
Cablelength is long gain36 0db
No alarms detected.
alarm-trigger is not set
Soaking time: 3, Clearance time: 10
AIS State:Clear LOS State:Clear LOF State:Clear
Version info Firmware: 20051006, FPGA: 20, spm_count = 0
Framing is ESF, Line Code is B8ZS, Clock Source is Internal.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (729 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 1:
4 Line Code Violations, 9798 Path Code Violations
4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
4 Errored Secs, 0 Bursty Err Secs, 4 Severely Err Secs, 501 Unavail Secs
Total Data (last 1 15 minute intervals):
4 Line Code Violations, 9798 Path Code Violations,
4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
4 Errored Secs, 0 Bursty Err Secs, 4 Severely Err Secs, 501 Unavail Secs

Yes, I am getting dial tone on both sets, when I dial a number I can see in debug out put that it accepts the digits.

mikej412

nagen wrote:

Almost same config on Router 2 (R2_3725) except clock source for T1 is set to Line
R1_3640#sh run
controller T1 1/0
framing esf
clock source internal
linecode b8zs
ds0-group 0 timeslots 1-8 type fxo-loop-start
ds0-group 1 timeslots 9-16 type e&m-wink-start

So you're trying to connect with fxo-loop-start signaling on both ends?

Does it work any better if you change it to fxs on one end?

nagen

mikej412 wrote:

nagen wrote:

Almost same config on Router 2 (R2_3725) except clock source for T1 is set to Line
R1_3640#sh run
controller T1 1/0
framing esf
clock source internal
linecode b8zs
ds0-group 0 timeslots 1-8 type fxo-loop-start
ds0-group 1 timeslots 9-16 type e&m-wink-start

So you're trying to connect with fxo-loop-start signaling on both ends?

Does it work any better if you change it to fxs on one end?

It works absolutely fine now, Thank you very very much teacher. I really appreciate it. I am doing self study. It was a valuable learning experience for me.

mikej412

nagen wrote:

I am trying to simulate PSTN, trying to route call through digital T1 CAS.

I think I learned more by trying to figure out how to use voice routers to simulate the PSTN and PBXs then if I actually had access to different PBXs and multiple PSTN connections.

It makes you start to understand what a PBX person is thinking, but without having to become a PBX person.

pullin-gs

I have two-way audio....it is the dialing that is odd.
On the gateway with the config:
!
controller T1 0
mode cas
framing esf
linecode b8zs
ds0-group 0 timeslots 1-4 type fxo-loop-start

I can dial to the gateway with the config:
!
controller T1 0
mode cas
framing esf
linecode b8zs
ds0-group 0 timeslots 1-4 type fxs-loop-start

I can not dial the other way though unless I configure TWO ds0-groups....one FXS, and another FXO group for both gateways.

Thanks

pullin-gs

pullin-gs wrote:

I have two-way audio....it is the dialing that is odd.
On the gateway with the config:
!
controller T1 0
mode cas
framing esf
linecode b8zs
ds0-group 0 timeslots 1-4 type fxo-loop-start

I can dial to the gateway with the config:
!
controller T1 0
mode cas
framing esf
linecode b8zs
ds0-group 0 timeslots 1-4 type fxs-loop-start

I can not dial the other way though unless I configure TWO ds0-groups....one FXS, and another FXO group for both gateways.

Strange.
FXO on both ends does not work at all
FXS on both ends does not work at all.

However, e&m-wink-start works fine both ways

Thanks

Flyingput

I am way late to this thread....
But today I was listening to Jeremy's GWGK video for reference on something, I happened to catch him saying "when configuring T1 CAS, fxo-fxo or fxs-fxs...."

fxo-fxs is the answer.

mikej412 wrote: »

I think I learned more by trying to figure out how to use voice routers to simulate the PSTN and PBXs then if I actually had access to different PBXs and multiple PSTN connections.

It makes you start to understand what a PBX person is thinking, but without having to become a PBX person.