What cisco command will give me this output

GigabitEthernet1/0/2 is up, line protocol is up (connected)
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 301429619
GigabitEthernet1/0/4 is up, line protocol is up (connected)
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 301428600
GigabitEthernet1/0/5 is up, line protocol is up (connected)
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 166983
GigabitEthernet1/0/7 is up, line protocol is up (connected)
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 170940
GigabitEthernet1/0/8 is up, line protocol is up (connected)

thanks............

Find more posts tagged with

Save $250 on 2025 certification boot camps from Infosec!

Book now with code EOY2025

Button

Comments

Monkerz

Show Interfaces will give you the info, along with other info...

MDCRTR01#sh int
GigabitEthernet0/0 is up, line protocol is up
Hardware is BCM1125 Internal MAC, address is 0019.5632.3f00 (bia 0019.5632.3f0
Internet address is 10.35.12.3/24
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 10Mb/s, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:08, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
7917794 packets input, 1026137507 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 6930970 multicast, 0 pause input
0 input packets with dribble condition detected
28576810 packets output, 2649233514 bytes, 0 underruns
12 output errors, 0 collisions, 3 interface resets
0 babbles, 0 late collision, 0 deferred
12 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
GigabitEthernet0/1 is up, line protocol is up
Hardware is BCM1125 Internal MAC, address is 0019.5632.3f01 (bia 0019.5632.3f0
Internet address is 10.131.1.2/24
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 2/255, rxload 6/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 1/75/0/0 (size/max/drops/flushes); Total output drops: 2061
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 26275000 bits/sec, 5371 packets/sec
5 minute output rate 11442000 bits/sec, 5033 packets/sec
1602038558 packets input, 3555873024 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
1673 input errors, 0 CRC, 0 frame, 1673 overrun, 0 ignored
0 watchdog, 292013847 multicast, 0 pause input
0 input packets with dribble condition detected
3226928178 packets output, 927128495 bytes, 0 underruns
3 output errors, 0 collisions, 2 interface resets
0 babbles, 0 late collision, 0 deferred
3 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out

mrblackmamba343

Monkerz wrote: »

Show Interfaces will give you the info, along with other info...

I know it would but I'm trying to put together some report and the report only needs that information not the entire output of the interface...

pitviper

Ahh, the power of regular expressions...

Try something like this:

ISR#sh interfaces | inc (Fast|Input que) 
FastEthernet0/0 is up, line protocol is up 
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
FastEthernet0/0.10 is up, line protocol is up 
FastEthernet0/0.20 is up, line protocol is up 
FastEthernet0/1 is up, line protocol is up 
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

PS that's a crapload of drops!

Monkerz

pitviper wrote: »

Ahh, the power of regular expressions...

Try something like this:

ISR#sh interfaces | inc (Fast|Input que) 
FastEthernet0/0 is up, line protocol is up 
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
FastEthernet0/0.10 is up, line protocol is up 
FastEthernet0/0.20 is up, line protocol is up 
FastEthernet0/1 is up, line protocol is up 
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

PS that's a crapload of drops!

You beat me to it. I was going to say:

sh int | inc (line protocol|Input queue)

hiddenknight821

You guys never cease to amaze me with the IOS command knowlege. I actually just learned something new. I guess I can relate what you just did to the pipe operator in linux. I tried to see if the ? would help me get the specific information I wanted to extract, but it only can give me this <cr>. I guess the pipe operator in IOS is a "secret" feature that was rarely discussed in my CCNA studies.

Priston

2621XM in packet tracer doesnt do |

Monkerz

That is because packet tracer is subject to the laziness of it's programmers.

Priston

I need get GNS3 huh?

Edit: I think my typing skills are just as bad as Packet tracer's IOSes

hiddenknight821

Monkerz wrote: »

That is because packet tracer is subject to the laziness of it's programmers.

I agreed. I wonder why is it that difficult to "plug in" the actual IOS in packet tracer. I mean they didn't have to create a pseudo-IOS in the first place. I know it would be pointless to have GNS3 if we have packet tracer with full-functional capability, but I always wonder if the memory is an issue.

hiddenknight821

Priston wrote: »

I need get GNS3 huh?

Yes. GNS3 would simualtes the actual IOS as if it was running on a router, with a slight adjustment.

Zartanasaurus

Priston wrote: »

I need get GNS3 huh?

Edit: I think my typing skills are just as bad as Packet tracer's IOSes

Yeah, Packet Tracer is a PITA when it comes to things like this. Same for not supporting config commands like switchport host.

And Cisco exam sims are Packet Tracer based.

Monkerz

Don't get me wrong, PT is great for CCENT, but once you get beyond that you need GNS3 or real gear.

mrblackmamba343

If I clear counters on interfaces in production environment what will the impact be?

pitviper

Should just zero out the counters with minimal impact. That being said, we had a site running a 2811 with 12.4 voice IOS that would completely crash when we tried to clear the counters after tons of serial errors. It appeared to be a hardware issue as the problem went away after we replaced the VWIC.