Disable SSH pix username and cisco password

Guys,

When setting up SSH on a ASA you have to enter a username and password, but once you set up your own username and passwords the ASA still accepts the usernamd pix and password cisco which allows you into the CLI.

I've tired no username pix but it says that the user pix does not exist, but still allows me through SSH?

Any suggestion please?

Find more posts tagged with

Comments

docrice

Can you show us the output of sh run | include username?

lon21

Cryptochecksum: 407633e1 8e6399be c7d2e49d e76f4aaf: Saved
: Written by enable_15 at 16:37:52.149 UTC Sun Sep 18 2011
!
ASA Version 8.2(1)
!
hostname New-York-ASA
domain-name TEST-LAB
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address 70.0.0.2 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
dns server-group DefaultDNS
domain-name TEST-LAB
access-list ICMP_Outside extended permit icmp any any
access-list acl-l2l-lon extended permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list nonat extended permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list nonat
nat (inside) 1 192.168.1.0 255.255.255.0
access-group ICMP_Outside in interface outside
route outside 0.0.0.0 0.0.0.0 70.0.0.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set esp-3des-md5 esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map l2lsites 10 match address acl-l2l-lon
crypto map l2lsites 10 set peer 20.0.0.2
crypto map l2lsites 10 set transform-set esp-3des-md5
crypto map l2lsites interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh timeout 30
console timeout 0
dhcpd dns 8.8.8.8
dhcpd option 3 ip 192.168.1.1
!
dhcpd address 192.168.1.5-192.168.1.132 inside
dhcpd enable inside
!

threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username Test password rfnvCarobquAQkOS encrypted
tunnel-group 20.0.0.2 type ipsec-l2l
tunnel-group 20.0.0.2 ipsec-attributes
pre-shared-key test
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
!
service-policy global_policy global
prompt hostname context
Cryptochecksum:407633e18e6399bec7d2e49de76f4aaf
: end

The username Test works perfectly fine, but also the default cisco username and password also work.

I want to be able to disable the default username and password.

Thanks

docrice

What happens if you change the password on the invisible "pix" and "test" accounts? Are you still able to SSH in with the original passwords? I'm running a newer version of the ASA code, but I'm not able to access it using any account other than what I've defined in my config.

lon21

docrice wrote: »

What happens if you change the password on the invisible "pix" and "test" accounts? Are you still able to SSH in with the original passwords? I'm running a newer version of the ASA code, but I'm not able to access it using any account other than what I've defined in my config.

Still able to access it via the default login, i guess the enable secret would stop unwanted access.

WillTech105

Try logging into the ASDM of the device and see if you can view that user account. If not, see if you can create the username cisco and change its password and see if it users the orignial password or the new one.

johnwest43

Give this a try

aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
aaa authorization command LOCAL

username USERNAME password PASSWORD privledge 15

lon21

johnwest43 wrote: »

Give this a try

aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
aaa authorization command LOCAL

username USERNAME password PASSWORD privledge 15

What do these commands do?

WillTech105

lon21 wrote: »

What do these commands do?

Telling the device to use AAA and look LOCAL (its own database) for a user -- in this case: USERNAME

lon21

WillTech105 wrote: »

Telling the device to use AAA and look LOCAL (its own database) for a user -- in this case: USERNAME

Sorry to be a pain, but what does 'aaa' mean?

aquilla

lon21 wrote: »

Sorry to be a pain, but what does 'aaa' mean?

AAA = Authentication, Authorization and Accounting

https://learningnetwork.cisco.com/docs/DOC-7905 - Introduction to AAA Implementation

shednik

johnwest43 wrote: »

Give this a try

aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
aaa authorization command LOCAL

username USERNAME password PASSWORD privledge 15

This will fix your issue, as of right now the PIX/ASA will accept authentication from the built in account and the local accounts until you specify the AAA group as show above.