issues with 2511

liven

My 2511 is hanging on the bootup....


When it gets to a line something like:


router undergoing cold start up ( or something like snmp agent undergoing cold start)....


I am not seeing any other errors... But I can't break into rommon mode...

I just want the darn thing to work, any suggestions?

Forsaken_GA

If you're letting it get to that point, you missed your chance to hit Rommon mode.

Power cycle the router and send the break sequence as soon as you see something appear

Just reread that -

Are you saying that it hangs after IOS starts, and that you're unable to break into rommon at all, or youre unable to break into rommon after it shows that?

My first suspect is your terminal settings, make sure they're correct.

tiersten

Post a log. You sure it is hanging?

liven

Forsaken_GA wrote: »

If you're letting it get to that point, you missed your chance to hit Rommon mode.

Power cycle the router and send the break sequence as soon as you see something appear

Just reread that -

Are you saying that it hangs after IOS starts, and that you're unable to break into rommon at all, or youre unable to break into rommon after it shows that?

My first suspect is your terminal settings, make sure they're correct.

Terminal settings are correct, I am sure of that.....

I can't get into Rommon mode at all.... I have tried sending a break every way I can think of. Used both hyper terminal and tera term.

liven

tiersten wrote: »

Post a log. You sure it is hanging?

I am pretty sure, I have let the darn thing boot for 30 minutes, and I can't console into it... Just keep getting the same non response....

liven

well I know it is not my computer, console cables or hyper terminal setup.

I can connect to other routers and switches without any problems...

But I can not console into my 2511... I can not break into Rommon...


The router boots, and I can see it go through the boot up sequence... but then int hangs....

tim100

liven wrote: »

well I know it is not my computer, console cables or hyper terminal setup.

I can connect to other routers and switches without any problems...

But I can not console into my 2511... I can not break into Rommon...


The router boots, and I can see it go through the boot up sequence... but then int hangs....

It's most likely the Flash.

liven

tim100 wrote: »

It's most likely the Flash.

I have two other 2500 (not sure what the exact model is but they are not 2511), can I take the flash out of one of them and put it in my 2511?

tech-airman

liven wrote: »

My 2511 is hanging on the bootup....


When it gets to a line something like:


router undergoing cold start up ( or something like snmp agent undergoing cold start)....


I am not seeing any other errors... But I can't break into rommon mode...

I just want the darn thing to work, any suggestions?

liven,

Has the 2511 ever worked?

tim100

liven wrote: »

I have two other 2500 (not sure what the exact model is but they are not 2511), can I take the flash out of one of them and put it in my 2511?

Yes. Give this a try and look at the boot up process. If it loads the IOS with no problem and boots up normally then the flash was the issue.

liven

tech-airman wrote: »

liven,

Has the 2511 ever worked?

Yes I used it alot for the BCMSN test because that test is very difficult to study for with dynamips.


I fired it up a few days ago to work on a few labs that is needed a switch (more than dynamips could provide), and it just hangs.

liven

ok I tried two different sets of Flash memory.....


I can get into Rommon now, but I can't get past the interfaces comming up.

I will post the boot info in another post.

liven

System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
Copyright (c) 1986-1995 by cisco Systems
2500 processor with 16384 Kbytes of main memory
F3: 7529592+103312+506436 at 0x1000

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-IS-L), Version 12.0(10), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Mon 20-Mar-00 22:09 by phanguye
Image text-base: 0x0000144C, data-base: 0x006F1994

cisco 2511 (68030) processor (revision D) with 16384K/2048K bytes of memory.
Processor board ID 02035869, with hardware revision 00000000
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
16 terminal line(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash partition 1 (Read/Write)
8192K bytes of processor board System flash partition 2 (Read/Write)

boot-start-marker
^
% Invalid input detected at '^' marker.

boot-end-marker
^
% Invalid input detected at '^' marker.

00:00:45: %SYS-4-CONFIG_NEWER: Configuration from version 12.3 may not be correc
tly understood
*Mar 1 00:00:56.287: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:00:56.947: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
*Mar 1 00:00:56.979: %LINK-5-CHANGED: Interface Serial0, changed state to admin
istratively down
*Mar 1 00:00:57.011: %LINK-5-CHANGED: Interface Serial1, changed state to admin
istratively down
*Mar 1 00:00:57.047: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-IS-L), Version 12.0(10), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Mon 20-Mar-00 22:09 by phanguye
*Mar 1 00:00:57.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
changed state to down
*Mar 1 00:00:57.979: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, c
hanged state to down
*Mar 1 00:00:58.011: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, c
hanged state to down

tim100

liven wrote: »

System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
Copyright (c) 1986-1995 by cisco Systems
2500 processor with 16384 Kbytes of main memory
F3: 7529592+103312+506436 at 0x1000

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-IS-L), Version 12.0(10), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Mon 20-Mar-00 22:09 by phanguye
Image text-base: 0x0000144C, data-base: 0x006F1994

cisco 2511 (68030) processor (revision D) with 16384K/2048K bytes of memory.
Processor board ID 02035869, with hardware revision 00000000
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
16 terminal line(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash partition 1 (Read/Write)
8192K bytes of processor board System flash partition 2 (Read/Write)

boot-start-marker
^
% Invalid input detected at '^' marker.

boot-end-marker
^
% Invalid input detected at '^' marker.

00:00:45: %SYS-4-CONFIG_NEWER: Configuration from version 12.3 may not be correc
tly understood
*Mar 1 00:00:56.287: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:00:56.947: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
*Mar 1 00:00:56.979: %LINK-5-CHANGED: Interface Serial0, changed state to admin
istratively down
*Mar 1 00:00:57.011: %LINK-5-CHANGED: Interface Serial1, changed state to admin
istratively down
*Mar 1 00:00:57.047: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-IS-L), Version 12.0(10), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Mon 20-Mar-00 22:09 by phanguye
*Mar 1 00:00:57.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
changed state to down
*Mar 1 00:00:57.979: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, c
hanged state to down
*Mar 1 00:00:58.011: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, c
hanged state to down

Boot into rommon and change your config register to 0x42 using the command o/r0x42 and then reboot again. This will bypass your NVRAM and ignore your startup configuration because you are running 12.0 IOS and in your startup configuration you have version 12.3 commands which might possibly be hanging it up. Try this and let's see what happens.

liven

Ok I change the confreg and was able to get into the boot image....


Looks like a bad image file:


Router(boot)#show flash ALL

System flash directory:
File Length Name/status
addr fcksum ccksum
1 11095548 c2500-c-l.123-22.bin [invalid checksum]
0x40 0x5383 0xFDD4
[11095612 bytes used, 5681604 available, 16777216 total]


I will wax it and load something fresh and see if that helps.

liven

Well thanks everyone for their help.


Turns out rolling back (way back 11.0(22a)) the IOS fixed the issue.

So if I can get by with that fine if not I will try a new IOS and see what happens...


ah the joys of hardware!!!


liven and learning!!!

tiersten

liven wrote: »

Turns out rolling back (way back 11.0(22a)) the IOS fixed the issue.

So if I can get by with that fine if not I will try a new IOS and see what happens...

Something is still broken. It shouldn't corrupt IOS on flash by itself.

liven

tiersten wrote: »

Something is still broken. It shouldn't corrupt IOS on flash by itself.

What do you think it could be?


I know these devices are more stable than a typical computer, however I would imagine it is possible for this (software corruption) to happen from time to time. Keeping in mind the device is pretty old....

Any suggestions would be appreciated!

networker050184

liven wrote: »

What do you think it could be?


I know these devices are more stable than a typical computer, however I would imagine it is possible for this (software corruption) to happen from time to time. Keeping in mind the device is pretty old....

Any suggestions would be appreciated!

The file usually gets corrupted during transfer. If it was working before and then suddenly became corrupted it could be bad flash.

liven

networker050184 wrote: »

The file usually gets corrupted during transfer. If it was working before and then suddenly became corrupted it could be bad flash.

Yes it was working for a while. However I had not used for some time and it was powered down. I am ready to start using it again and it hangs during boot.


I have some extra flash so I will put some new flash in there and see what happens.

Thanks gentlemen.