Problem Dial peer with MC3810 V3

Papooooo

Hi guys,

I just grab one of the famous MC3810 and try to make it work with 2 analog phone.
The thing is those phones are basic analog, don't have power, i was thinking the FXS port gonna power them like the standart RJ11 do.
Do i need to have some analog phone with power cable or maybe they are a special command to make it good.
Also maybe my FXS ports don't work.
Can someone help me .... please......

mikej412

It doesn't get much simpler than this

Use the commands in this doc to verify your ports and configuration.

How about the output of a show version command and your dial peer configuration.

Papooooo

The link you gave me doesn't work but I am was able to find a dial peer configuration step.
but still don't work.

maybe my AVM card in 3810 died!!!!

Anyway ...Here is a Show version.



Cisco MC3810-V3 (MPC860P) processor (revision 18.07) with 57344K/8192K bytes of memory.
Processor board ID 22598607
PPC860 PowerQUICC, partnum 0x0005, version X01(0x0001)
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
MC3810 SCB board (v01.F0)
1 Multiflex T1(slot 3) RJ45 interface(v03.A0)
1 Six-Slot Analog Voice Module (v07.B0)
1 Analog FXS voice interface (v03.A0) port 1/1
1 Analog FXS voice interface (v03.A0) port 1/2
1 Analog FXS voice interface (v03.A0) port 1/3
1 Analog FXS voice interface (v03.A0) port 1/4
1 Analog FXO voice interface (v04.A0) port 1/5
1 Analog FXO voice interface (v04.B0) port 1/6
1 2-DSP(slot2) High Performance Compression Module(v01.A0)
1 Ethernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
1 Channelized T1/PRI port(s)
256K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (AMD29F016)

Configuration register is 0x2102


Here is show run :

MC3810#sh run
Building configuration...

Current configuration:
!
version 12.1
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname MC3810
!
!
!
!
!
!
network-clock base-rate 56k
ip subnet-zero
no ip domain-lookup
!
!
!
!
!
!
cns event-service server
voice-card 0
!
!
!
!
!
controller T1 0
!
!
interface Ethernet0
no ip address
shutdown
!
interface Serial0
no ip address
shutdown
!
interface Serial1
no ip address
shutdown
!
router isis
!
ip classless
no ip http server
!
!
!
voice-port 1/1
!
voice-port 1/2
!
voice-port 1/3
!
voice-port 1/4
!
voice-port 1/5
!
voice-port 1/6
!
dial-peer voice 5501 pots
destination-pattern 5501
port 1/1
!
--More-- Translating "MC3810"
dial-peer voice 5502 pots
destination-pattern 5502
port 1/2

mikej412

Papooooo wrote:

but still don't work.

And by not work, what exactly do you mean? No dial tone?

Did you do a show voice port summary
Did you take a phone off hook and try a show voice port summary
Are you sure you're plugged into the correct port?

And what IOS image and version are you using -- since that wasn't in the output of the show version command you posted.

Papooooo

I tried take a phone off hook and try a show voice port summary
Nothing happen.
Are you sure my analog phone don't need a external power ?
Maybe my FXS port died.

MC3810#show voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
====== == ========== ===== ==== ======== ======== ==
1/1 -- fxs-ls up dorm on-hook idle y
1/2 -- fxs-ls up dorm on-hook idle y
1/3 -- fxs-ls up dorm on-hook idle y
1/4 -- fxs-ls up dorm on-hook idle y
1/5 -- fxo-ls up dorm idle on-hook y
1/6 -- fxo-ls up dorm idle on-hook y


16384K bytes of processor board System flash (AMD29F016)

Directory of flash:/

2 -rwx 7980148 Mar 01 1993 00:07:17 mc3810-factory-IOS
3 -rwx 7653052 Mar 01 1993 00:11:18 mc3810-a2ik2sv5-mz.121-3a.T1.bin

mikej412

Unless you are using a wireless phone, you don't need power.

I've got a couple of cheap analog phones that have a call display and caller ID built in -- those I have to put batteries in to power the display before they will work. The cheapest analog phone with no display or extra features gets it power through the FXS port.

Papooooo

Thanks for all,

Maybe I am just a non lucky guy, cause i bought this from ebay and maybe those FXS port are just died or other hardware problem.

mikej412

Are the phones you're using known working phones? Have you tried them on your home phone line?

What does a show voice port 1/1 give you