Ap-1131ag

I have reset my AP but when it comes back to the ap> prompt and asks for the password "cisco" does not work. I know it is reset because the hostname was not "ap" when I turned it on.

I don't have any experience with these yet and don't know if I am doing this right.

Thanks

Find more posts tagged with

Comments

tiersten

Default password for the APs is Cisco with a capital C.

boostinbadger

Thanks!

What does a basic config usually look like?

chrisone

Well i havent played with Cisco APs in a while since i moved jobs and im focused more on ASA's. I would expect it to be a short basic config , you will probably see stuff like the Radio configs , they should be turned off by default last i remembered. However the APs are designed to be configured using the web gui. I would suggest configuring these APs with the GUI. Good luck!

boostinbadger

What is the default IP? 192.168.1.1?

tiersten

boostinbadger wrote: »

What is the default IP? 192.168.1.1?

I can't remember exactly but I believe it uses DHCP by default. Either way, use the console and have a look.

Megadeth4168

I believe the default IP is 10.0.0.1 and that the default SSID is tsunami.

One issue that I've run into with configuring these through the web browser is that the newer browsers don't react well. Firefox didn't seem to work at all... IE7 works but it is still a little flaky. I prefer the CLI myself.

mikem2te

boostinbadger wrote: »

Thanks!

What does a basic config usually look like?

This is my not quite so basic configuration. If you can get the GUI working that is the best method although not entirely inuitive.

I got two SSIDs on the AP, one fully open for just internet access, the other using WPA2 with dot1.x authentication for my internal LAN. Each SSID is bridged to a different VLAN on the ethernet sub interfaces.

Current configuration : 5292 bytes
!
! No configuration change since last restart
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname AP1130AG
!
enable secret 5 XXXXXXXXXXXXXXXXX
!
aaa new-model
!
!
aaa group server radius rad_eap
 server XXXXXXXXXXXXXXXXX auth-port 1645 acct-port 1646
!
aaa group server radius rad_mac
!
aaa group server radius rad_acct
!
aaa group server radius rad_admin
!
aaa group server tacacs+ tac_admin
!
aaa group server radius rad_pmip
!
aaa group server radius dummy
!
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
!
aaa session-id common
ip domain name XXXXXXXXXXXXXXXXX.co.uk
!
!
dot11 syslog
!
dot11 ssid Internet
   vlan 201
   authentication open
   mbssid guest-mode
!
dot11 ssid Trusted
   vlan 200
   authentication open eap eap_methods
   authentication key-management wpa version 2
   mbssid guest-mode
!
power inline negotiation injector 001d.e5ca.c4ac
!
crypto pki trustpoint TP-self-signed-3847650946
 enrollment selfsigned
 subject-name cn=IOS-Self-Signed-Certificate-3847650946
 revocation-check none
 rsakeypair TP-self-signed-3847650946
!
!
crypto pki certificate chain TP-self-signed-3847650946
 certificate self-signed 01
 XXXXXXXXXXXXXXXXX
  quit
username admin privilege 15 secret 5 XXXXXXXXXXXXXXXXX
!
!
bridge irb
!
!
interface Dot11Radio0
 no ip address
 no ip route-cache
 !
 encryption vlan 200 mode ciphers aes-ccm
 !
 ssid Internet
 !
 ssid Trusted
 !
 mbssid
 station-role root
 no dot11 extension aironet
 bridge-group 1
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
 bridge-group 1 spanning-disabled
!
interface Dot11Radio0.200
 encapsulation dot1Q 200
 no ip route-cache
 bridge-group 200
 bridge-group 200 subscriber-loop-control
 bridge-group 200 block-unknown-source
 no bridge-group 200 source-learning
 no bridge-group 200 unicast-flooding
 bridge-group 200 spanning-disabled
!
interface Dot11Radio0.201
 encapsulation dot1Q 201
 no ip route-cache
 bridge-group 201
 bridge-group 201 subscriber-loop-control
 bridge-group 201 block-unknown-source
 no bridge-group 201 source-learning
 no bridge-group 201 unicast-flooding
 bridge-group 201 spanning-disabled
!
interface Dot11Radio1
 no ip address
 no ip route-cache
 shutdown
 no dfs band block
 channel dfs
 station-role root
 bridge-group 1
 bridge-group 1 subscriber-loop-control
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
 bridge-group 1 spanning-disabled
!
interface FastEthernet0
 no ip address
 no ip route-cache
 duplex auto
 speed auto
 bridge-group 1
 no bridge-group 1 source-learning
 bridge-group 1 spanning-disabled
!
interface FastEthernet0.200
 encapsulation dot1Q 200
 no ip route-cache
 bridge-group 200
 no bridge-group 200 source-learning
 bridge-group 200 spanning-disabled
!
interface FastEthernet0.201
 encapsulation dot1Q 201
 no ip route-cache
 bridge-group 201
 no bridge-group 201 source-learning
 bridge-group 201 spanning-disabled
!
interface BVI1
 ip address XXXXXXXXXXXXXXXXX 255.255.255.0
 no ip route-cache
!
ip http server
ip http authentication local
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
logging XXXXXXXXXXXXXXXXX
radius-server attribute 32 include-in-access-req format %h
radius-server host XXXXXXXXXXXXXXXXX auth-port 1645 acct-port 1646 key 7 XXXXXXXXXXXXXXXXX
radius-server vsa send accounting
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
 exec-timeout 20 0
 transport input telnet ssh
!
sntp server XXXXXXXXXXXXXXXXX
end

AP1130AG#

sulaywan

tiersten wrote: »

Default password for the APs is Cisco with a capital C.

Thanks man,
May God Bless you !