Packet Tracer Activity 3.22

gbdavidx

How can you check for answers for these? I'm trying to do these on my own but there are no answers...

Anyways, it wants you to add static routes from the ISP but the one they gave you makes no sense

ISP(config)#ip route 192.168.1.4 255.255.255.252 172.16.1.6



the link to the router is 172.16.1.5

i tried adding static routes for 192.168.2.0 (network for r2) and 192.168.1.0 (network link for r1) and they said it was incorrect and it also wants one more

gbdavidx

no one?

inscom.brigade

google packet tracer 3.22, you'll get hits. Which semester is it from? semester 1,2,3,or, 4?

http://www.ranet.co.th/packetlab/ccna/NA-3-2-PPP-CHAP.pka

that is the only 3.2 that I have

I think maybe
it looks like this one,,








PT Activity 3.2.2: Configuring Basic Frame Relay with Static Maps
Topology Diagram

Addressing Table


　
Device


Interface

IP Address


Subnet Mask

R1

Fa0/1


192.168.10.1


255.255.255.0




S0/0/0


10.1.1.1


255.255.255.0

R2

S0/0/0


10.1.1.2


255.255.255.0




S0/0/1


209.165.200.225


255.255.255.224

R3

Fa0/0


192.168.30.1


255.255.255.0




S0/0/0


10.1.1.3


255.255.255.0

ISP

S0/0/1


209.165.200.226


255.255.255.224




　
Learning Objectives
• Configure Frame Relay
• Configure static Frame Relay maps
• Configure the Frame Relay LMI type
All contents are Copyright © 2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 3
　
CCNA Exploration
Accessing the WAN: Frame Relay PT Activity 3.2.2: Configuring Basic Frame Relay with Static Maps
　
Introduction
In this activity, you will configure Frame Relay on the serial 0/0/0 interfaces of routers R1, R2, and R3. You will also configure two static Frame Relay maps on each router to reach the other two routers. Although the LMI type is autosensed on the routers, you will statically assign the type by manually configuring the LMI.
Routers R1, R2, and R3 have been preconfigured with hostnames and IP addresses on all interfaces. The Fast Ethernet interfaces on routers R1 and R3 are active, and the S0/0/1 interface of R2 is active.
Task 1: Configure Frame Relay
Step 1. Configure Frame Relay encapsulation on the serial 0/0/0 interface of R1.
R1(config)#interface serial0/0/0
R1(config-if)#encapsulation frame-relay
R1(config-if)#no shutdown
Step 2. Configure Frame Relay encapsulation on the serial 0/0/0 interfaces of R2 and R3. Step 3. Test connectivity.
From the command line on PC1, verify connectivity to the PC3 host, located at 192.168.30.10, using the
ping command.
The ping from PC1 to PC3 should fail since the R1 router does not know how to reach the 192.168.30.0 network. R1 must be configured with a Frame Relay map so that it can find the next hop destination to reach that network.
Step 4. Check results.
Your completion percentage should be 43%. If not, click Check Results to see which required components are not yet completed.
Task 2: Configure Static Frame Relay Maps
Step 1. Configure static maps on R1, R2, and R3.
Each router requires two static maps to reach the other routers. The DLCIs to reach these routers are as follows:
Router R1:
• To reach router R2, use DLCI 102 located at IP address 10.1.1.2.
• To reach router R3, use DLCI 103 located at IP address 10.1.1.3. Router R2:
• To reach router R1, use DLCI 201 located at IP address 10.1.1.1.
• To reach router R3, use DLCI 203 located at IP address 10.1.1.3. Router R3:
• To reach router R1, use DLCI 301 located at IP address 10.1.1.1.
• To reach router R2, use DLCI 302 located at IP address 10.1.1.2.
The routers must also support RIP; therefore the broadcast keyword is required. On router R1, configure the static Frame Relay maps as follows:
　
All contents are Copyright © 2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 2 of 3
　
CCNA Exploration
Accessing the WAN: Frame Relay PT Activity 3.2.2: Configuring Basic Frame Relay with Static Maps
　
R1(config-if)#frame-relay map ip 10.1.1.2 102 broadcast
R1(config-if)#frame-relay map ip 10.1.1.3 103 broadcast
Configure routers R2 and R3 using the previously provided information.
Step 2. Check results.
Your completion percentage should be 79%. If not, click Check Results to see which required components are not yet completed.
Task 3: Configure the Frame Relay LMI Type
The Frame Relay cloud contains switches that are using ANSI as the LMI type. Therefore, all the Frame
Relay links must be manually configured to use ANSI.
Step 1. Configure ANSI as the LMI type on R1, R2, and R3.
Enter the following command on the serial interface for each router.
R1(config-if)#interface s0/0/0
R1(config-if)#frame-relay lmi-type ansi
Step 2. Check results.
Your completion percentage should be 100%. If not, click Check Results to see which required components are not yet completed.
Step 3. Test connectivity.
It is possible to complete the activity with a 100%, yet still not have connectivity. PC1 and PC3 should
now be able to successfully ping each other and the web server. If not, make sure that you entered all the commands exactly as specified in the previous steps.
　
All contents are Copyright © 2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 3 of 3


[URL]http://L:\Software\Packet tracer\Paket tracer labs\263\Chapter 3\3.2.2\E4_PTAct_3_2_2.pdf[/URL]

gbdavidx

its from semester 2, chapter 3, routing protocols

Zartanasaurus

What about it doesn't make sense? I'm assuming R3's other IP is 172.16.1.6, yes?



You need 2 specific static routes on the ISP router that point to the 2 serial links on R3. The one you have in bold is right, so you need the other one.
The way to check your answer is to ping the serial IPs on R3 from the ISP router.