One way audio with FXS and STCAPP

evanr

Hello everyone, I hope maybe someone can help me out.
I have a cordless phone connected to my 3725 on FXS port 1/1/1.
System image file is "slot0:c3725-adventerprisek9-mz.124-12.bin"


PROBLEM: I call my cordless from my cell. Cellphone can hear voice, but callee on the cordless phone can not hear anything.

What could be the problem here?

stcapp ccm-group 1
stcapp
!
!
!
voice rtp send-recv
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
redirect ip2ip
h323
emptycapability
ip circuit max-calls 10
session transport udp
sip
registrar server expires max 3600 min 600
!
!
!
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
codec preference 4 g723r63
codec preference 5 clear-channel
!
voice-port 1/1/1
timeouts interdigit 12
timing hookflash-in 50 0
description LEFT FXS PORT
station-id name HOMEPHONE
caller-id enable
!
ccm-manager config server 172.16.1.1
ccm-manager config
!

sccp local FastEthernet0/0
sccp ccm 172.16.1.1 identifier 1 priority 1
sccp
!
sccp ccm group 1
associate ccm 1 priority 1
!
dial-peer voice 6 voip
description ## INBOUND DID ##
translation-profile incoming INC
voice-class codec 1
session protocol sipv2
session target dns:callcentric.com
session transport udp
incoming called-number <snip>
dtmf-relay cisco-rtp rtp-nte digit-drop h245-alphanumeric
no vad
!
dial-peer voice 100 pots
service stcapp
port 1/1/1
forward-digits 0
!
dial-peer voice 2 voip
description ### LD USA ###
translation-profile outgoing OUT
destination-pattern 1[2-8]T
voice-class codec 1
session protocol sipv2
session target dns:callcentric.com
session transport udp
dtmf-relay cisco-rtp rtp-nte digit-drop h245-alphanumeric
!
dial-peer voice 3 voip
description ## ASTERISK ##
destination-pattern 2T
session protocol sipv2
session target ipv4:192.168.200.2
session transport udp
dtmf-relay cisco-rtp rtp-nte digit-drop h245-alphanumeric
codec g711ulaw
!
sip-ua
authentication username <snip>
no remote-party-id
retry invite 4
retry response 3
retry bye 2
retry cancel 2
retry register 5
timers register 250
registrar dns:callcentric.com expires 3600
sip-server dns:callcentric.com

telephony-service
max-ephones 2
max-dn 2
ip source-address 172.16.1.1 port 2000
no caller-id name-only
calling-number initiator
time-zone 8
create cnf-files version-stamp 7960 Oct 24 2013 20:19:21
voicemail 202
max-conferences 4 gain -6
transfer-system full-blind
transfer-pattern .T
secondary-dialtone 9
!
!
ephone-dn 1
number 100 secondary <sip#> no-reg primary
label Home Telephone
call-forward busy 202
call-forward noan 202 timeout 30
!
!
ephone 1
mac-address D295.021E.0281
type anl
button 1:1

evanr

On 2811 seems to work fine. Waiting for additional memory for 3725 to see if an IOS upgrade solves these problems.

mistabrumley89

Just looking at this makes my head hurt and makes me afraid to even start CCNA Voice lol

evanr

Heh. I know. I welcome the challenge, and honestly Voice a lot of fun because you get to directly see [hear] the product of your work! Ringing phones! Also keep in mind I have a lot of stuff in this config that is probably NOT on the CCNA voice, mostly SIP trunk stuff. I'm just starting CCNA Voice but so far I have heard no mention of SIP trunking.