-
CCNP Building Scalable Internetworks (BSCI 642-901) Lab Portfolio
Hello, Is "Cisco Student Guide Volumes I and II" book the same as : "CCNP Building Scalable Internetworks (BSCI 642-901) Lab Portfolio" by Cisco Networking Academy ? http://www.ciscopress.com/markets/detail.asp?st=44737 http://www.ciscopress.com/bookstore/produc...isbn=1587132133 Have someone ever used those books ? Are…
-
Final hurdle cleared... I is a CCNP
Crushed the ONT this morning. Moving on to something else, QoS or ARCH. It will depend on which book arrives first.
-
aaa issue with none method
Hi, I am doing some tests with aaa, and I found a gotcha I cant quite explain. If i configure aaa in the following way for logins: aaa authentication login MYTEST local none What i expect to happen is that the user will be authenticated with the local user database, and only in case of error querying this or timeout will…
-
Ospf nssa
Hi guys i have been working my way through the Official BCSI cert guide and well i must say it leaves you hanging a bit. but this is not a post to flame how bad the book is Any way the section on stub area's is not very good and dose not cover enough i feel and compleatly lacks true life situations where to opt for 1 or…
-
Yersinia Layer 2 attacks
Is anyone here familar with the Yersinia software for making layer 2 attacks, I have having touble finding documention on it besides the yersinia website
-
isis needing unnumbered interface...
tried to do this: router isis net 49.0001.1111.1111.1111.00 int fa 0/0 ip router isis then got error: Cannot enable ISIS-IP. Configure IP address or make the interface unnumbered Not finding much on this error on the web.... if anyone has a suggestion please speak up!!!
-
issue with totally stubby area
ok I went into an interface and did this: R3(config-router)#area 34 stub no-summary which worked: but then about 40 seconds later I got this (the dead timer is set to 40): *Mar 1 02:52:27.247: %OSPF-5-ADJCHG: Process 1, Nbr 172.16.4.1 on Serial0/1 from DOWN to DOWN, Neighbor Down: Dead timer expired Dead timer expired…
-
dot1x via RADIUS
Greetings all, I've been playing alot with dot1x via RADIUS as a means to assign switchports to a specific VLAN based upon the authenticating user in AD. I have the GUEST and AUTH_FAIL VLANs working flawlessly as far as I can tell, with the exception of some latency that doesn't exist when authentication is successful via…
-
Voip Site surveys
Hi, does anyone on the board go to new sites and spec what they require etc to install Voip. ive just been told i will be involved and eventually taking over the site surveys for our division. This is something im looking forward to and hopefully i can get some voip experiance along the way. At the min i dont have any voip…
-
Switch Pricing
I'm trying to find the following for a home lab: 2 or 3 2950's 2 3550's How much do used 2950's and used 3550's usually go for? Assuming all 24 port? What's a good price?
-
new asdm? then what?
hey ccsp gurus i have my new asa 5505 right on it it has asdm-524.bin so i found a asdm-613.bin copied it to its flash and ran in the globla config mode the command "asdm image disk0:/asdm-613.bin and nothing happens i cannot acces it with the ip but if i go back and config the old asdm-524.bin it works fine? do i have to…
-
BCMSN & wireless
Hi, I was just wondering if anyone could recommend any web resources for the wireless section of the bcmsn. I feel this is probably one of my weakest area's and need more resources to back up my knowledge of this area. I dont have any wireless kit to practice on nor have i worked with cisco wireless kit before. Any…
-
Translation rules practice
It would be nice if there were some translation rules practice online somewhere if someone knew where it might be found. If anyone knows of any, please let me know.
-
ONT - Passed.
I just passed my ONT exam. What a relief, I was really nervous for this one, but it all worked out. :)
-
BSCI failed
Failed my BSCI exam again. 700 out of 790. Felt good going into this. I do well in OSPF,EIGRP, ISIS, ok in BGP. Sims are easy. It's Ipv6 and Multicast that get my and i spend alot of time on it for studing. I think the thing that really kills is that all of the practice tests i take. Cisco, Transcender etc there are barely…
-
pumping ccnp out like candy!
YouTube - Into The World of CCNP found this school that gives high school students free access to be a ccnp where the hell was this when I was a kid! lucky teens my god how lucky can you get all the time in the world to take class after class why i have to work and do my studies holy crap must be nice....
-
2650XM, 3640, BSCI Lab Routers
I'm having a hard time deciding which routers to purchase for my BSCI lab. I've currently got 3 2650XM's - is there anything that the 3640's can do that they can't? I'm thinking about getting a few 2501 or 2514s for end-point devices - would this be wise? Any advice welcome Edit: Also - is there a big difference between…
-
what else should I grab for my CCNP lab?
So I'm going through one more acquisition phase before I start my CCNP studies. Currently my lab consists of: everything is maxed or running the latest ios 4 x 2501 1 x 2620 3 x 1710 3 x 2950 (enchanced) 1130 AP 2511 access server What else should I look at grabbing up? I'm probably going to borrow a couple 3550 from work…
-
What Interfaces are necessary for CCNP Lab?
I posted this in the CCNA section but I want to build my lab so that I can use it for my CCNP in the future as well. I currently own: 1 2514 Router 2 2950 Swithces 1 3550 Switch I need to buy 3 more routers (1 as a frame relay switch). I'm thinking about the following: 1 2610 w/NM-8A/S as frame relay switch 2 3640's with…
-
KDC Event ID:11 from Unity servers
Anyone seen this message before? There are multiple accounts with name MSSQLSvc/serverA.domain.com:1433 of type DS_SERVICE_PRINCIPAL_NAME. I found some info in MS website - Event ID 11 in the System log of domain controllers I have also found the duplicate SPNs in my 2 Unity servers. Anyone knows what ramifications this…
-
Got a surprise email from Cisco just now.. 4011 Recognition
I didn't know that the SND awarded a 4011 recognition, so it was a pleasant surprise to check my email and find that I'd achieved it. I'm pretty happy because it's NSA and CNSS backed. This will do great things for my career :) Just wanted to share the good news!
-
Back-2-Back VIC-2E/Ms?
Anyone ever try doing this between 2 gateways? I have some old cards laying around, and this article makes it sound like it's possible using type II and V settings: E&M Type I - This is the most common interface in North America. -Type I uses two leads for supervisor signaling: E, and M. -During inactivity, the E−lead is…
-
ISCW - Test scheduled for 2/5/09
It's on. I've been studying for this test for the last 5 months and I'm ready to kick some IPSec/MPLS/DSL/Firewall ass! I'm not sure why but I'm more intimidated by this test than I was for the BSCI or BCMSN. Anyway, I'll be hittin' the books and GNS3 pretty hard for the next 2 weeks. Wish me luck!
-
Routing on a stick with ASA
This config is not working, can someone tell me why. I cannot ping each other from each sub-interface. They are connected directly together. Edge router: ! interface FastEthernet0/0 no ip address speed auto ! interface FastEthernet0/0.1 encapsulation dot1Q 1 native ip address 172.17.56.2 255.255.255.252 no snmp trap…
-
IPv6 practice
Anyone know of a good site/book/resource for practicing ipv6 stuff... Not necessarily routing and what not, just getting more familiar with the addresses etc.... Thanks
-
ASA Active/Active or VPN Cluster
Greetings, I have an obvious ASA question. We have two ASA's that will be used for VPN access. Initially only IPSec connections but eventually, we'll be using the SSL Web connections as well. I was curious which failover configuration would be more appropriate. Active/Active or the VPN Load Balancing Cluster. I was…
-
Call preservation with SRST
I know that calls using MGCP and CAS will be preserved, but not using MGCP PRI, as the D channel gets torn down and backhauled during SRST, resulting in a dropped call. What about H.323 using CAS and PRI? I've read that Cisco has new features using H.323, but only with a specific (or higher) IOS. But generally speaking,…
-
Numbers passed to POTs
Hi guys, can anyone tell me if the numbers passed from cisco go across on block or overlapping ? I've run a debug on the cisco and can see the numbers being dialed passing across to the pots but I cant confirm if they are over-lapping or not? I can see configurations to change the status on incoming isdn, but cant see on…
-
help newby to asa 5505
hey ccspers, I have this asa 5505 I picked up. Nice...I know it comes ready out of box and I know how to change the ip ranges etc... to match my internal network at home. but this is my issue. I have a SMTP(exh 2003 EE), OWA and WWW both using HTTPS 443 and 444 respectively. but is it static mappings that I can do in my…
-
Can't Believe I Passed ISCW
Just a few questions in I started having problems with sims, which I think was a resolution issue. They rebooted the computer and the problem remains. At this point I've lost about 5 minutes of the actual exam time. The testing people don't really give me an answer, so I say "screw it" and do the sim even though I can't…
-
Netflow on ADSL
We have a few private adsl lines at small remote offices using cisco 877's. Now, when configuring netflow on the interfaces it only seems to send back statistics from multiple interfaces for the inbound and outbound traffic. I.e the dialer will send back outgoing stats and another will send back the incoming stats. So each…
-
Tera Term Function Keys
Does anyone know if it's possible to set a function key such as F6 to replace having to type the sequence Ctrl + Shift + 6 in Tera Term? I've been trying to edit the KEYBOARD.CNF file with no luck. When I use the keycode.exe program, Ctrl + Shift + 6 shows up as keycode 1543 but I'm not sure where or how it needs to be…
-
CT rises from the dead (yes...again!!)
OK. I'm going to try this yet again. Time to start cranking out this BCMSN exam. I've been half way through this material from scrap on two separate occasions. The first was a good 18 months ago. The second was while I was studying for the Composite about 6 months ago. I'm going to pick up on Chapter 12, where I left off…
-
3550 smi ready for EMI?
Hey guys how do you know an SMI 3550 switch with SMI image will take a EMI image? what specs do I look at to know before I buy this switch off of ebay? I can get an EMI image; is it the size of the image and the flash size? thanks
-
What is exactly in a home router?
I have a small question. what is exactly 'in' a linksys (your company name here) wireless router? Wireless is layer 2. So, is it a router, (4 port) switch, or both? I have seen a video on Youtube and have seen that only one card is inside. Thanks! es
-
starting CCIP
just wanted to stop in to the CCIP forum. i purchased the qos exam guide today and will begin studying qos next week. I have a bunch of study material to include: >ONT triansignal >ONT CBT Nuggets >QOS CBT Nuggets >GNS3 should be fun! anyboday else have any other study material for the QOS exam?
-
Passed BCMSN today
Finally sat the exam today and knocked it out, score was an 864 which is fine by me, a pass is a pass. I had to reschedule this thing 3 times do to family health problems and other issues but now it is done. I used Cisco's official guide, CBT nuggets, some lab work, on the job work, and some free online material I was able…
-
Passed 642-892 Composite
I passed the Composite on Sunday February 1st. I found that the test wasn't too bad. 66 questions on routing and switching. I got an 895, which wasn't too bad considering I only spent 5 days really studying. It helped that I do routing and switching every day at work. Now onto ISCW and ONT. Hopefully by the middle of the…
-
BSCI passed! 2/6
BARELY! 100% EIGRP - Cake 60% OSPF - Not sure what happened (I think it was the v3 questions which was about IPv6) 85% ISIS - Fairly straightforward 80% IOS features - Route maps, distribution 72% BGP - Mixed bag 87% Multicast - Straightforward 50% IPv6 - Very hard, goes beyond concepts Materials: Cisco Press Study/Exam…
-
ISCW - Cisco press questions from book
Question 4 in chapter 21 in the ISCW cisco press book says: What type of firewall is best used when only UDP is used for access? A) Packet filter B) Authentication proxy c) ALG d) Stateful packet filter From the info on page 527 "A stateful packet filter treats each protocl in unique fashion......... However UDP does not…
-
Argh--Cisco Specialist Kit lost in mail
Argh, my Cisco Firewall Specialist Kit was lost in the mail and Cisco's response is "you have to buy one for $15 because it didn't get returned to us". Nice.
-
RIP distribute-lists
I'm working through the BSCI Lab Portfolio and I've come to the Challenge for Redistribution between OSPF and RIP (lab 5-1), The challenge wants me to filter out a couple routes from coming into the RIP process using an extended access list. The thing I'm confused about is that it says to look at Step 5, which has to do…
-
back on the horse (CAM/TCAM)
right back to the CCNP, got myself some energy drinks some tunes in my ears ready to go! playing with CAM/TCAM tables tonight does anyone know a way to see a time stamp for an entry in the CAM table?
-
packet tracer 5.0 opinons??
hey ccnpers! do you guys have any opinions on Packet Tracer 5.0 training. Is it really good. I mean. I can see why people can pass with sims on the exams due to well a sim is a sim. and working on real equipment thought i like it better to me isnt the same look and feel as the exams on the sims. so it seems that the sim…
-
BSCI question on study materials???
Okay I am going to get the CCNP BSCI command book ; I really liked my ccna one. and I want to get the cisco press lab portfolio that looks good but there are many BSCI cisco boooks which ones are the best? cisco press BSCI study-guide???which one is good lab portfolio i am getting...opinions on anyone? ccnp bsci command…
-
What you think I should pursue next?
Hi guys, Today I passed my BSCI exam on my first try. However, the result (822) is very poor and a little unsatisfactory for me but the important thing is that it is in the past. The good thing is that I did not use any MODERATED crap, I rather fair 822 then 950-1000 with cheating ;) I now wonder which exam to start…
-
EIGRP accross a wan
What is the best way to get eigrp accross a mpls network. Is a gre tunnel the best way or is there a better way for eigrp to send and receive accross it. We are using a quest mpls with public ip addresses assigned by quest. I know frame relay will send eigrp accross. My goal is to get redundancy if our mpls fails i would…
-
Multiple VPNs on Cisco 837
Hi, This post isn't related to CCNP but I thought it would be best suited here due to its content. :) We have two offices that have bog standard ADSL in them with a Cisco 837 router. Each office has a static IP and the router does NAT for the users at each office. I would like to achieve the following abjectives without…
-
I passed the BCMSN
I took the test on 1/19 and failed with a 796 I took the test again on 1/25 and passed with an 864 I really did bad on voice and spanning-tree the first time around. I felt strong in spanning-tree, especially since I deal with it so frequently on the job. I went back and reviewed wireless, voice, and spanning-tree using…
-
BCMSN redux tomorrow morning - Update failed 778, but it gets interesting
Still burning from my first ever failure Worked quite a bit on STP, redundancy and voice Anyone want to bet on my chances of getting a section on PVLAN configuration? UPDATE - Failed with a 778 but get this, I had no less than 3 questions on OSPF, IPv6 route summarization and IPv6>4 tunneling. Did I totally miss this in…
-
1760 router serial medium card????
Okay guys are serial cards wic type for 1760 cisco routers really 280 usd??? my god the router itself is 99.00 wt??????? help I am looking for only 1 serial DTE/DCE port card for my 1760 router can i find one cheap anywhere?????? thanks
-
CME v4 Memory requirments
Hi All I'm looking to load CME v4 onto a couple of routers and was wondering what the recommended memory requirements are (Dram and Flash)? I already have a 1760 with FXO/FXS and PVDM-8 and I'm looking on ebay at a couple of Cisco 2611XM routers. The 2611XM's may also be used as Gatekeepers! PRESENT Cisco 1760 - 96Mb/32Mb…
-
When will the CCNP be updated next?
I am going to probally wrap up the CCNA this month. I am leaning towards the CCNP next, but, does anybody know when the CCNP will be updated?
-
PIX syslog error
Starting this morning, getting a lot of these: <code> Feb 04 00:00:34 10.22.151.13 local4.alert %PIX-1-105008: (Primary) Testing Interface 2 Feb 04 00:00:35 10.22.151.13 local4.alert %PIX-1-105009: (Primary) Testing on interface 2 Passed Feb 04 00:00:50 10.22.151.13 local4.alert %PIX-1-105008: (Primary) Testing Interface 2…
-
Facebook - The Jeremy Cioara Appreciation Society
Was just on Facebook and thought I'd search for Jeremy Cioara randomly, the only result that appeared was his appreciation society. Enjoy! The Jeremy Cioara Appreciation Society | Facebook Also found his blog recently for anyone who doesn't know about it. Cisco Blog
-
Router--switch--asa
So we have an edge router that is doing everything your can possibly think (NAT, Firewall, VPN, MPLS Traffic, Internet traffic etc). We bought some ASA's and want to offload the Firewall and VPN stuff to it. From initial talks the physical layout will be router, switch and then ASA. I always thought the ASA was inline to…
-
putty command line tool
I am trying to find to find a terminal emulator I can run form the command line under windows. what I will have is a windows box with 4 serial cables connected to some Cisco stuff. I have installed putty and the command line tool that comes with it 'plink' but can't see optios for a serial connection only ssh,raw and…
-
QOS Labs?
Looking for some good QOS labs but don't see an awful lot online. Does anyone know if the ONT Lab Portfolio book is any good? Any other resources that I should look at? Thanks!!
-
Basic information
-
just Passed CCNA
Hi every one i just passed ccna exam and i wanna go 4 CCVP but somepeople told me that i shouldn't go 4 ccvp untill i know enough about voip and they recomended ccnp first would u help me about that plz?can i go for ccv directly or it would be hard 4 me?
-
another stupid EIGRP question (multicast hellos)
ok, so working through the ccnp bsci lab book... Challenge lab states that I need to prevent multicast hello's between two devices.... Well I know the passive-interface command will do this. But won't that break the EIGRP neighbor relationship? Is there any way to prevent the multicast and still maintain neighbor relation…
-
Cisco retires 642 -901 exam [not]...
hxxp://www.cisco.com/web/learning/le3/current_exams/642-901.html I HAVE A FEW FRNDS WHO TOOK THE EXAM LAST WEEK EVEN ONE THIS MORNING AND NOW THE CISCO SITE SAYS THE EXAM IS RETIRED................ THIS IS JOKE..........
-
Passed BSCI 1/31/09
I passed the BSCI exam today with a score of 911. Thanks to Techexams for all of the great post related to the BSCI exam. I am just two exams away from being a CCNP. Moving on the ISCW :) STUDY MATERIAL CBT Nuggets Train Signal Cisco Press Books GNS3 / Dynamips
-
Passed ONT today now CCNP!!
I passed the ONT exam today finally completing my CCNP certification after starting on it 1.5 years ago after not being regular with my study habits.
-
What is exactly in a home router?
-
I need help figuring out this 1750 with a voice card
Router#sh diag Slot 0: C1750 1FE VE Mainboard Port adapter, 4 ports Port adapter is analyzed Port adapter insertion time unknown EEPROM contents at hardware discovery: Hardware Revision : 8.1 PCB Serial Number : JAD05290KHX Part Number : 73-3743-08 Board Revision : A0 Fab Version : 04 EEPROM format version 4 EEPROM…
-
BCMSN Tomorrow Morning
If you had to pick only one topic to go over the night before the test, what would it be? Feeling good, as long as they don't throw in too much on LWAPPs
-
L2TP vs. GRE
Hey guys, trying to determine what exactly the difference between these two protocols. I know from studying ISCW that you can use GRE to create tunnels between two routers. Can you use L2TP as well or is it mostly use from PC to endpoint? Does this give you the added PPP protocol functionality between the routers?
-
ASA 5520... with two exits to Net
I've read with interest the new features of the ASA's, particularly regarding load balancing with dual ISP's. The conditional static route feature, via SLA monitoring and tracking, is sweet. I have a situation that a bit different... we have a single ISP with whom we've recently negotiated a backup link, over wireless. The…
-
Access port set to nonegotiate causes issues?!?
So yesterday i configured an access port for one of our sys admins. After doing so he was not able to ssh into the box connected to this port from a different vlan. However, after removing the switchport nonegotiate setting he was able to ssh into the box without issue. So my questions is whether or not this was mearly a…
-
Best WAN for Voice
Hi there, I'm trying to find ideas for a big project for my company. I work for the Canada air traffic control. We have a new system that can be use a T1 line for pass voice but not calls, it's only voice (it's a PTT signal (Push-to-talk)). A frequency is assigned to the aircraft from his position to talk to the control…
-
OSPF interArea: /32 prefixes
Hi, I have 2 routers R2 and R3 in a point-to-point serial connection. OSPF is configured. R2 is getting interArea routes forwarded by R3. I still don't know why R2 gets /32 prefixes these routes. example on R2: " 192.168.9.0/32 is subnetted, 1 subnets O IA 192.168.9.1 [110/65] via 172.16.23.3, 00:01:09, Serial0/1 "…
-
ASA 5505 failover help
hi everyone, im trying to get failover to work on 2 ASA 5505 units. i believe the failover is configured correctly, but for some reason i cant access the standby asa thru the wan ip. i can log into the primary unit, initiate the failover. the 'active' light on the primary unit goes amber but it loses wan connectivity…
-
HWIC Firmware Update?
Do you update HWIC firmware?...or is this all taken care of in IOS software? Silly question but my boss just told me to update the HWICs I just put in our 3825.....It has the latest IOS.
-
Class-based policing and CAR question
Let's say you want to police all traffic from Class A to 64,000 bps and Class B to 64,000 bps, and that you want to police the combined traffic being sent out an interface to 96,000 bps. I tried this with CAR using the following config: access-list 100 permit <Class A match criteria>access-list 101 permit <Class B match…
-
BCMSN: sh int fa# switchport -> operational mode?
Hi all, I've begun studying for my BCMSN and ran into something odd today. I have two switches set up, both are set to dynamic desirable. When running sh int fa0/16 switchport, I get the following output: XX-C2950_A#sh int fa0/16 swit Name: Fa0/16 Switchport: Enabled Administrative Mode: dynamic desirable Operational Mode:…
-
642-533 ips
I've passed all the CCSP exams except 642-533. How hard to you folks suspect it is to pass 642-533 without having acces to an Cisco IPS appliance for practice? We have a Cisco IPS 4215 at work but it's on a classified network and in production use, so I can't really muck with it. And a co-worker set it up--I only helped…
-
cisco network academy
packet tracer 5.0 has anyone used packet tracer? and cisco network academy? what are the pros and cons? and do you use real routers and switches or are all your work is done in sims? thanks robert
-
BCMSN Lab portfolio Q
Hi guys, Just working my way through some labs while im on my break in between uni semesters and have a Q on etherchannels. Ive been doing the etherchannel labs and i understand the difference between a L2 and L3 channel and how to setup the actual etherchannels. But say you have 2 L3 switches and you create a L3 core…
-
RAS and GKTMP similarities
As I'm learning all the infininte acronyms in CCVP, I see a lot of the same ones in RAS and GKTMP (e.g. ACF, ARJ, LRQ, etc.) Is there an easy way to differentiate the messages between these two in my head without getting confused? There seems to be overlap, and the two are not the same thing.
-
ISCW IPSEC High Availability
The Cisco press book has a chapter on IpSec high availability yet CBT nuggets nor train signal have anything on it. And the module list thing from the cisco web site also has nothing on it. Why would the book include a chapter on it when it doesn't seem to be on the exam?
-
Passed BGP+MPLS Composite, finished CCIP
It was a very tough exam - harder than the BSCI+BCMSN composite. It seemed like a very out-dated exam that required the knowledge of legacy stuff that isn't used a whole lot any more. I scored a 932 and literally took the exam down to the last 30 seconds. I'm done with the CCIP now. I'm going to finish my studies on the…
-
HSRP vs. SRST
Could someone clarify the major differences between HSRP and SRST? When would a person use one over the other? (I have my own notes, but I want to see what others say).
-
Passed BSCI
Last week I failed this exam (http://www.techexams.net/forums/ccnp/39299-failed-bsci.html), but true to my word it is now one week later and I passed it this time around with an 855. I put in a bit of studying over the weekend and felt quite confident going in, though it is still not an exam to be taken lightly. In any…
-
ONT Scheduled- This Saturday
Hey Everybody, I been @ the ONT full-time for 3 months now, and I'm ready. Any last pointers, not looking for give aways ; )
-
IPSec GRE tunnels & interesting traffic
Something has just come to my attention while studying GRE tunnels. Here is the config that SDM has generated from one side of my tunnel (minus irrelevant info) R1#sh run Building configuration... Current configuration : 3695 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec…
-
Book recommendation for CIPT
I'm going for the 642-444 CIPT test before long, and I'd like some input as to which textbook is the best to study for this? As the book selections for the topic all seem to be between 600-1000 pages long, I doubt that I'll be buying more than one, so I want to make sure that I get the right one. I know Jeremy Cioara has a…
-
starting CCIP
-
ASA5520 failover problem
Actually, the failover works great! It works seamlessly. I'm pretty sure the problem is the Checkpoint firewalls on the other end of these tunnels anywho, here's the background: Our main firewall (ASA5520) has an active/standby failover setup. Said firewall has NUMEROUS VPN connections. Two of those VPN connections go to…
-
BCMSN Cisco Press Lab Guide - Help -
I started to do the BCMSN Lab from the Cisco Press Lab Guide.I'm stock on Page 31 where I have to verify that the PC router has connectivity with devices in VLAN1 by using ping commands. I'm going to copy the config from my PC router and the Access switch that is directly connected to the PC Router. PC_ROuter ConfigCurrent…
-
Will this be any help for the SND??
Hacking Exposed Cisco Networks I bought this awhile ago and never started to read it, I think I may shoot for the SND before it expires. Wanted to know everyone's thoughts if you've read it and took the SND exam if you thought this book would be helpful.
-
BCMSN Books?
I know this has been asked a MILLION times already, but most of the posts I saw were fairly outdated, along with the stickies. I already ordered the CiscoPress book - are there any other good ones out there?
-
EtherChannel groups - Help
You can see the Lab that I'm working on the following link topology on Flickr - Photo Sharing! My problem is that I can ping all the switches and PC router on the right side of the building, but not the left side (PC2 - ASW2 and ADW2) and the left side can't ping either left or right. The following are the config from the…
-
redistributing connected routes into ospf/eigrp
Ok so here is the topology I'm running, it's pretty simple: ooo R1 R2 R3 R1 is running OSPF. R2 is running OSPF on f0/0 (interface to R1), and EIGRP on f0/1 (interface to R3). R3 is running EIGRP. I am emulating connected interface on R2 with loopback0. Now, when i redistribute connected into R2's router eigrp process, R3…
-
Fallback Bridging
Has anyone here ever actually used fallback bridging outside of a lab environment?
-
OSPF Adjacency
Something interesting I came across today while browsing the web. We all know that for an OSPF neighbor relationship to form the subnet mask must match on each side of the link. What I came across today states that the subnet mask will be ignored on point-to-point links and virtual links. I decided to lab it up and it does…
-
help! great deals on 1760 routers but???
Hey CCVPers, Gosh a guy cannot win. You get screaming deals on a bare bones say 1760 router with 1 10/100 FE port but crap a 1 WIC1-ENET is 200 bucks or so is this true. where can I get a wic1-enet cards for 50 USD bucks or less? am I dreaming? man! I looked on ebay yikes the routers are fairely cheap but the cards yikes!
-
Best WAN for Voice
-
Confused on congestion avoidance along with congestion management.
Hi, I am a bit confused on when to use wred along with your queuing mechanism. Study material goes into some depth on what wred does, however, my question is, you normally use both right? congestion management to get your packets to the hardware queue in the fashion you want, and wred to make sure the queues within…
-
Dynamips autostart = false
Found the answer,need to execute "start SW1" I'm having some issue with the autostart feature, if i dont include it in my config as in the case with R6 all is good, once i run my .net file i can telnet to the router in question.When i do enable this feature the router doesnt initalize so i cant telnet to it. What am i…