-
CCNA Home Lab?
Hello guys I was wondering if this will be sufficient Home Lab for obtaining my CCNA? Thanks Cisco CCNA 2500 2501 2513 2514 Router 2950 Switch Lab | eBay
-
how to convert decimal 3 200 000 to binary ?
Hi could anyone tell me how to convert decimal 3 200 000 to binary ? I can convert smaller decimal number to binary using the binary positions like 128 64 32 8 4 1 2 ...... but how could I convert decimal 3 200 000 to binary without writing the long binary position until that number? is there a way to calculate it?…
-
Cisco Lab Build
Hey Experts! Please help and let me know if this is a good build. Routers: 1 x 3800 Series 3845 Router w/3845-MB VWIC-2MFT-T1 & 64 MB Card 2 x 2811 Switches: 4 x Cisco Catalyst WS-C2960-48TC-L Should I add another 3845 or 2811 to have 4 switches and 4 Routers ? Would you recommend adding maybe a L3 Switch or not really…
-
CCDA 200-310 Pass
Passed this bad boy last week with a healthy score (above 900) The exam went very well in my opinion even though some questions really threw me. For the preparation I used CBT nuggets through our company provided subscription and the Cisco official cert guide. I wasn't really that impressed with the nuggets and the booked…
-
DHCP Server on a different subnet
Hello, How do I allow my 2PCs on 172.16.0.0 subnet recognise that my DHCP Server on 192.168.1.0 subnet is there and is wanting to share a range of IPs? Thanks for your help in advance as always! :)
-
Knowledge Feels Scattered - Looking for Study Tips (ICND1)
I've been trying to find a good study plan for the ICND1. The problem is I find myself reading material and thinking "I know that, I know that... I don't know that." My knowledge from previous studying is very scattered. For example, I can configure an intervlan LAN with a router on a stick to route to the vlans on…
-
need some help on this comand
need some help on this command ! ! interface GigabitEthernet1/0 mac-address 0000.1111.1111 ip address 10.14.0.1 255.255.255.0 negotiation auto> what it's this commad no shutdown
-
ITPro.tv and CBT Nuggets quick comparison
These two services have their own qualities, and are good in their own right, but I managed to make a direct comparison the other night. I am studying for CCNA R&S and needed to learn about GRE. I watched Don Pezet present GRE in 39 minutes. I then flicked over to Jeremy Cioara and got exactly the same info in just over 7…
-
Subnetting question.
Hi I am new to Cisco. I have a assignment that requires to connect and configure devices on a topology in packet tracer but I am stuck on one instruction. hope someone could help? it said "Use 10th class “C” private network to assign subnets for serial link with appropriate mask" . I am not sure what this means? I know…
-
having problem what they do? the six different BGP neighbor states
having problem what they do? the six different BGP neighbor states: Idle, Connect, Active, Opensent, Openconfirm, and Established
-
EIGRP Classless Question
Hello, I am using PacketTracer and I can't make EIGRP create a new adjacency with a classless network. For example I have the network set as 192.168.0.0/30 with no auto-summary and I get the below messaging spamming itself. R1 %DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 192.168.0.1 (GigabitEthernet0/0) is up: new adjacency…
-
Some great studying advice from Keith Bogart
I was searching around trying to find out how Keith Bogart studies. My personal goal is to be able to explain the CCNA topics in the same level of depth that he does... someday. I stumbled across this video today with lots of great advice for people studying for the CCNA/NP/IE, etc. He also talks about forgetting what he…
-
200-125 passed
Hi all, So today I passed the 200-125 (the composite CCNA R&S) exam. I was a little too nervous at the start of the exam. I used the Cisco official study guides mainly for this exam. My study: About 4 months ago I started studying using Todd Lammle's book, and covered it in about maybe 2 1 month of study for about 2 hours…
-
what to study for BGP? ICMD2 v3
what to study for BGP? ICMD2 v3
-
How to get this serial connection up?
https://www.dropbox.com/s/lsfn6mdm2pv6bqg/acl.pkt?dl=0 I was wondering if anyone can help me get this going between the two routers on the serial (red) line. I tried int on the connection port on both routers with no shutdown but the lights won't come on. There should also be a vlan of 192.168.3.6 on that connection, not…
-
Did my 2950 just die?
I've two 2950 Switches in my lab setup. Been fine until I powered my lab up today. One of my 2950s now has a flashing orange SYST light. On power up, the STAT light flashes green and the SYST light is steady orange. After apx 3 seconds, the STAT light goes to steady green and the SYST light goes to flashing orange. And…
-
Port-Security - Security Violation Count
Hello, I have noticed that if I use shutdown as my parameter the security violation count works but if I use the parameter protect it does not increment the security violation counter? Is this normal or am I missing something? Thank you in advance!
-
Question about autonegotiation on Catalyst switches
Hello I'm studying for the ICND1 exam, and have a question concerning autonegotiation. So, according to Wendell's book, the following rules apply if the other end of the link does not send autonegotiation messages (autonegotiation disabled on one end of the link): Speed: sense the speed (without using autonegotiation), if…
-
Router to Switch encapsulation - What is this called?
Hey, I have a router and a switch - I have created a VLAN and I have allowed the switch to access that VLAN successfully. I have G0/0 which I have gave 1.1.1.1/30 and I created G0/0.1 which I gave 192.168.1.1/24 So my two questions are as follows: G0/0.1 When I add a dot after an interface and I tell it to use…
-
A guide I am following to make big bucks.
https://www.youtube.com/watch?v=ZGuSMui3ohQ Watch the first 15 minutes.
-
Switch ACL
Are Switch ACL's part of 100-105 ? I assigned an ACL to a switch vlan 1 interface,it blocked ping to that vlan IP but allowed Ping's throw to the Router, in effect the ACL did not filter packets passing throw, why is this ?
-
VLANs Allowed on Trunk
Could someone please explain to me what it is I'm missing regarding VLANs Allowed on Trunk. I'm studying from the W. Odom book ICND1 100-101: Chapter 9. On page 255, there's a sample output which reinforces the text regarding the 'allowed VLAN list' feature, which sates "By default, switches include all possible VLANs…
-
Class A subnetting question (newbie one)
I'm independently studying Cisco with CBT Nuggets. I'm having some issues grasping subnetting when it comes to Class A in one of the reviews. I'll share a couple of expamples, followed by some questions. A) 10.25.66.15.4/23 Mask 255.255.254.0 (correct?) B) 63.24.89.21/18 Mask 255.255.192.0 (correct?) Why does example A…
-
CCNA/CCENT Latest Changes?/Hardware Recommendations
So I know a lot of the exams have just changed, and material has changed (as of Sept or whatever?). Anyways im coming from a career in QA (Now doing Automation Engineering, mostly Rails/Ruby stuff. So I have an ok coding background). Anyways i've been looking to make some changes to my career, getting into networking…
-
CHAP Authentication and VTP in 100-105 ?
I looked in the ICND1 100-105 Exam topics on cisco.com and I couldn't find CHAP or VTP in the exam topics, are they removed ?
-
Router on a stick
Hello People I have been googling but cannot seem to get my setup quite right. Im doing a course for electricians and am having trouble with an aspect of it. This is my first course involving networking so CLI is very new and strange to me but I'm slowly picking it up. I have a 1841 router connected to a 2950 switch. The…
-
CDP Layer Same VLAN ?
Does CDP Work even if 2 switches are interconnected with each other Via Access Port, but are on Separate VLANS ? SW1 Fa0/1 VLan 20SW2 Fa0/3VLAN 30 Can sw1 still get the Ip address and everything else from show CDP Neighbors Detail regardless of VLAN ?
-
CHAP authentication with secret passwords
Should CHAP authentication work with secret passwords? I'm only able to configure it using local plain text passwords with the 'username' command. Currently using: (C3725-ADVENTERPRISEK9-M), Version 12.4(15)T14 on GNS3
-
Logging question
why does not the logging buffered counter increment. show logging : Console logging: level debugging, 13 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 13 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 0 messages logged, xml disabled, always I get…
-
Destination MAC address?
Hello, I am confused as to what destination MAC will be in a layer 2 frame. In the below example: PC1>>>SW1>>>>R1 e0/1 interface>>>>SW2>>>Server 1 If PC1 wants to send information to Server one on a different subnet with R1 in the middle, will the destination MAC in the frame leaving PC1 be the MAC for SW1 or the MAC for…
-
Vlsm and Summariration
i have ip address 172.0.0.16/16 Company need to devide to 30,100,500,5 how can do this?And afte summariration.
-
15min before exam Start ? 100-105
Hey guys is it true that I have 15min to write down information on a Board before I start my exam ? Thankyou ^___^
-
Exam Day 100-105 subnet chart ?
Hey guys I was wondering if I had enough time on exam day before taking the test to write out my multiples of 16, 8, 4 for mask of 240,248,252. That way I can subnet very fast :D , do they let me write on the board before exam ?or after the exam starts ? I feel as though I am at a disadvantage because of my math skills, so…
-
Urgent Questions about subnetting
Question 1: Given a Network of 172.16.0.0 /16 You want to divide the network into subnets. You will allow at least 600 nodes per subnet, what is the subnet size? (26??) What subnet mask should you use? (255.255.255.192 /26) What are the first 2 subnets What is the address of the first node on the first subnet? What address…
-
DHCP and DHCP relay agent help, packet tracer cisco. help me
i need to set up the switch as dhcp server that needs to address ips for the 3 different lans , i was able to set up dhcp working for the 10.9.0.0/24 network however i cant get it working for either R1 or R2 networks , ive tried 'ip helper-address" commands many times but never worked out. things to note , everything can…
-
2811 Router
Can you run video ip phones off an 2811?
-
What if we do not define outside interface in NAT configuration?
Say, a typical NAT configuration, that has "ip nat inside source" and inside interface defined. The translation and the reverse translation are done at the inside interface. Routing outward/inward are done by the routes. It seems to me in this case, everything should function even we skip defining the outside interface.
-
Magic HAT Subnetting ,
Hey guys i plan on taking the CCENT 100-105 very soon, and i understand that time is the essence for subnetting. Im pretty that I've gotten the concepts of subnetting down, and finding out what given ip address / mask belongs to which subnet using the Magic Hat, 256 - Mask = Value method. However, i am having trouble with…
-
RIP Split Horizon.
is the ip split-horizon interface command part of 100-105 ? how do i check/verify split horizon ? Route poisoning the Metric is 16 in the debug command.
-
Subnet Calculator
Hi all, Few months ago I've decided to build online subnet calculator after I didn't find any online tool that works for me the tool support ipv4 / ipv6 and i also added a subnetting guide https://subnet.ninja i'd like to get feedbacks on the guide or on the calculator 10x
-
Finding the IPv6 Prefix from an Address/Length Value
Hi can anyone help me with these given prefixes ? I am suppose to find the prefix length / value and I am having a lot of trouble in Wendell Odoms ICN1 book. It seems like he doesn't explain this concept very well as most prefixes I've seen so far are /32 /48 /64 most common. 34BA:B:B:0:5555:0:6060:707/80…
-
DHCPv6
what is the dhcpv6 unique identifier and is dhcpv6 packet tracer configuration required for 100-105 ?
-
Full time student studying for CCNA
Greetings everyone, I'm new to the forum and new to IT. I'm currently a full time CS major but something about IT (cisco networking specifically) caught my attention while strolling around campus. After doing some research, it really sparked an interest and I have been studying for the CCNA exam in my spare time (15 units…
-
Ip address/subnet
I start learining ccent i have problem with topic ip/subnet can you help me? [FONT="]Which subnet does host 172.45.188.29 255.255.255.0 belong to? First i write number with binary and second step problem[/FONT] [FONT="]What is the last valid host on the subnetwork 172.40.36.0 255.255.254.0?[/FONT]
-
Failed 100-105 Exam :(
So, this was my first ever Cisco exam. Scored a 556/832, and mid-way through the exam, the computer crashed and I had to wait 5 minutes (thankfully, my exam results weren't lost...phew). Basically, I need to work on everything: Network Fundamentals: 0% LAN Switching Fundamentals: 44% Routing Fundamentals: 47%…
-
210-060
What is the passing score for this test? I can't find it on Cisco's website. Thanks
-
Zero to CCNA?
I need some more technical certs to bolster my current set. If I were to start studying for a CCNA, about how long would it take until I should take the exam? I have almost no networking experience. I did once manage a Cisco ASA 5510 in one of my environments (did very simple things in it like assigning port address…
-
Multiswitch VLAN Without VLAN Trunking
I wonder if this would be of interest to others. This .pkt file URL]https://dl.dropboxusercontent.com/u/7015711/CCNA/VLAN%20PAGE%20240.pkt[/URL is a little exercise that I set myself. It’s based upon fig 9-3 on page 240 of the ICND1 100-101 Wendell Odom book and is aimed at those studying for CCNA. For those without access…
-
Question about unknown unicast frame flooding
When a switch forwards an unknown unicast frame, it obviously will flood the frame out of all ports except the one it came from. Does the switch replace the frames destination mac address with mac broadcast addrress and then flood it? (FF:FF:FF:FF:FF:FF) or just leave the original destination mac address in place and then…
-
Exam Day
Hey all, Just wanted to give a heads up I'll be writing my 100-105 CCENT exam in 2 hours. Fingers crossed, will update after. :D
-
STP vlan bridge root cost question..
I have a question about the vlan and bridge root cost. my topology on vlan 40, the sw2-1 it's the bridge root cost and sw 2-3 and sw 2-2 are cost is 4. the question it's from 2-4 to get to root bridge I need to pass from 2-2 or 2-3 to get to 2-1, the cost is 4, why is not 8? sorry I hope this can explain. thank you so much.
-
GRE protocol stack location
From Odoms ICND2 material on GRE - "The routers encapsulate the original packet inside a tunnel header, which takes the place of the serial link’s HDLC header." Later in the chapter he says.. "GRE is not a TCP or UDP application. Instead, GRE acts like another transport protocol in that the GRE header follows the IPv4…
-
200-105 Study Group
Hi, Is anyone interested in joining a study group? I'm currently enrolled in WGU's ICND2 course and I need a study buddy to get through/ discuss the material with. I'm getting a bit overwhelmed with some of the topics(STP, OSPF, EIGRP) . I have 3 months and some change to pass the exam. We can meet on Sat or Sunday and…
-
Failed CCNA:DC DCICN 640-911
I am not sure if I was just not in the right state of mind, didn't take the exam seriously because I have passed CCNA and work at a NOC, or if the OCG written for 640-911 falls short and I trusted it too much to do the job. I am usually a decent test taker, and I have not failed a single test (school or certs) in my entire…
-
CCNA Book or Video training
Hello everyone I m' thinking of studying by myself in order to pass the CCENT/CCNA ICND1 and ICND2 exams. I was wondering based on your experience, which is best, book or video training? If book, should I buy the hard copy or the digital version? Are they the exact same thing? Do I get all that is included in the hard copy…
-
Kevin Wallace CCNAv3 Videos on SafariBooks
Kevin Wallace's CCNAv3 Videos were just released on SafariBooks. Just in time for my ICND2 studies. I have INE's 200-120 videos (didn't pass the CCNA in time) and was looking at buying the 200-125 videos as well, but I think that I'll just use the 200-120 + Kevin Wallace's vids.
-
NAT Ping Translations.
Should the number of NAT translations due to a Ping be 10 , 5 echo request and 5 echo reply ? should the: show ip nat translations show 10 translations ?
-
Opinions on these kits?
Are these CCNA certification kits worth it from certificationkits.com? Been debating on getting one to lab at home with and get more familiar with the stuff. Thanks for your thoughts!
-
Subnetting question
10.0.0.0/17 is my subnetting correct ? /17 = 255.255.128.0 Network bits = 8 Subnet bits = 9 Subnets = 2^9 =512 Host bits = 17 First subnet = 10.0.0.0 First host = 10.0.0.1 Last Host = 10.0.0.254 Broadcast address =10.0.0.255 Next subnet is 10.0.1.0 and next is 10.0.2.0 uptil 10.0.127.0 this gives a total of 128 subnets…
-
stp and cost
I don't get why sw2 is only a cost of 4. if you add a cost of 99 at the link? why it is 4? I need more practice examples.
-
Question about vlan trunk troubleshooting
Ι have two switch sw1 ,sw2 with dif vlans assgned .they are connected with a trunk and working.when i for example disable vlan 10 (#interface vlan 10 ,shutdown .i can still use the trunk link and send frames.why is this hapening? SW1#show interfaces trunk Port Mode Encapsulation Status Native vlan Gig0/1 desirable n-802.1q…
-
Switchport sticky question.
why does the sticky parameter give an option for a mac address ? sticky just learns the first mac on the interface, so why is a mac option given ? from PT: Switch(config-if)#switchport port-security mac-address sticky ? H.H.H 48 bit mac address <cr>
-
DHCP question
Does a router show excluded address's only which are assigned to the Router itself ?Any servers within the excluded range on the same range do not increase the excluded address count in sh ip dhcp pool? 192.168.1.1 is a router intf gw. 192.168.1.10 is assigned to a server getting a static IP. All are connected to a switch…
-
Passed 100-105 Today!
Score: 953/1000 I think that I spent too much time studying for this test. Mostly due to poor study habits. The test was fairly easy, which is to be expected with most multiple choice tests. I completed the test with over 50 minutes left on the clock. Resources Used (In order from most to least used) 1. Wendell Odom 2.…
-
Help with Configuring switch ports/device communication
Say I have a router and three switches. The switches currently have all ports enabled, they need to communicate with each other and have connectivity to the router as well. How do I do this? Which ports should be connected and enabled and what have you? I've been messing with packet tracer trying to figure this out. Thanks
-
Which IOS version to configure ethernet sub-interfaces on a 2611/2621 router?
Hi, i'm attempting to set up trunking 801Q on a 2621 router with software version 11.3 (2) XA4. Looks like this IOS does not support trunking according to the Cisco feature tool. How do I/or where can i download a newer IOS for my router to enable trunking it it's sub interfaces?
-
Opinion of Practice Tests
Hey all, I just scheduled my 100-105 CCENT exam for October 25th (20 days from now). What would be a good practice tests to use? I heard Boson is harder than the exam itself.
-
IPv6 SLAAC
From a pearson's question in the Odom book: With SLAAC ,the host learns the prefix from a router using NDP RS/RA messages. The host can use EUI-64 Rules or use a defined process to randomly generate the interface ID value. what is the randomly generated method is my question ?
-
2 switches 1 router
Hi guys, i'm trying to run 2 switches (2960 POE and other non POE) with 2 differents IP on 1 router (cisco 2811). One is basically only for 7911 phones and the other for CIPC connected to PCs with DHCP from a network router, but I cannot make each nets to ping themselves. Thanks in advance for your feedback Attached you…
-
boot system command
If I set the Router to boot from tftp as I did: boot system tftp asa842-k8.bin 192.168.1.2 the image from tftp stays in the tftp server and does not get loaded to Router am I correct ? I am confused as the show version shows the older IOS. should i run the copy command also ?
-
A bunch of Cisco stuff from work.
I'm starting my journey to get my ICND1 and I'm in the process of planning on building my own lab. We got some Cisco equipment at work that are not currently being utilized; I don't know if they have any value for I don't have any idea what they are I'm a total noob when it comes to networking and I'm hoping you guys can…
-
Passed ICND1 last month and ICND2 today - Finally got that CCNA.
After taking classes at my local college and going through Wendell Odom's book and passing the ICND1 - CCENT last month, finally passed ICND2 today and got that CCNA, the day before ICND2 - 200-101 expires. Boy that was a relief. It's been a year and a half journey (if you include the classes I took at the local college),…
-
exam number for ICND2
what is difference between ICND2 640-8xx and ICND2 200-1xx???
-
Book Help
I studied for the ICND1 and ICND2 for the CCNA R&S through videos but mainly by reading two great books from Lammle and Odom. I'm now interested in getting the CCNA Service Provider certification. I'm simply unable to find equivalent great books for CCNA SP. Would someone provide suggestions? Thank you.
-
Study material to CCNA Security?
Hello everyone! I'm thinking of taking this cert but I've heard terrible things about the OCG and I'm not really sure what other sources for material is available. Could someone please point me in the right direction? Thanks in advance!
-
What is a switch card?
As shown in the diagram, the hub router has a switch card to connect one of its subnets. The EIGRP topology shows as the below, corp@sh ip eigrp topology P 10.1.1.0/24, 1 successors, FD is 25625600 via connected, Vlan1 The question is what vlan1 stands for? Is it the internal network interface for the default VLAN? Also,…
-
HSRP load balancing
Need some help with HSRP load balancing. on Wendell Odom book page 553, is talking about HSRP does support load balancing by preferring different routers to be the active router in different sudnets. so each Valn have router as active and configure like "ROAS" router on a stick. the next step is layer 3 switch . this is…
-
CCNAS Material vs CCNA R&S?
Hello, I'm recently CCNA R&S certified and currently studying for CCNP R&S. The plan after I receive the NP is to go after my CCNAS. Was wondering if anyone here could share from experience the overlap in the CCNA R&S vs Security material? Is there a whole lot of overlap? Or very little? Also if you'd be willing to share…
-
What is major purpose of default route?
Hello everyone i am preparing for ccent i have studied term default route . I am thinking ablut it about 3days. But i can not understand exact major purpose of default route. Because 0.0.0.0 0.0.0.0 next router ip . Why we need this default route? Actually i know it is for using stub network that has one exit. Every router…
-
Router Stablization Question
Hi all, I'm noticing my 2811s are tilting a bit in my lab. Anyone have a suggestion if there's a special set of brackets I can purchase?
-
Packet Tracer 7 on Windows XP
I managed to install PT 7 on windows XP I get an UPnP error ,but seems to be working fine. Tried running PT on Ubuntu does not work.... Is it OK to run PT 7 on XP ?
-
Passed ICND1!
Woo hoo! Passed it! Thank you Jeremy Cioara at CBT Nuggets! and Odom and the Cisco press book. Also to Lammle and the ITPro.tv team. All great resources. I purchased a 3550 switch and a 2811 router. Important, but so goddamned noisy! When I couldn't stand the noise, I used GNS3. Onto ICND2....
-
CCENT/CCNA old training materials
How useful are the CCENT/CCNA old training materials when it comes to preparing for the current exam? Im talking about the older 200-120 study materials.
-
Cisco SG300-10 pinging problem
Good afternoon, I am currently building a layer 3 switch. It has been almost 4 years since I touched a Cisco switch/router, so any help would greatly be appreciated. The following is my current running config. GWPCoreSW1#show running-config config-file-header GWPCoreSW1 v1.4.0.88 / R800_NIK_1_4_194_194 CLI v1.0 set system…
-
IPv6's interface ID
I read "MAC addresses are considered to be uniquely assigned worldwide" so interface ID can be generated from the MAC. But is this assumption correct?
-
Test lab
I want to be able to connect my test environment from my office. I'm running a testlab with 3x routers, 3x switches and a access switch. this lab is not on the same floor as where my office is, and the only way to connect the lab to my office is through the production switch. before I go further with this I wanted to see…
-
Any value???????????
Is there a lot of value to the collaboration certification?
-
Anyone want to study together for the CCENT?
Hi, I never study when I'm by my self. I want to study with someone and talk with someone about the material we're studying. I don't have a book yet but I can purchase a Udemy video or something. I mean we can go over what you know if you're ahead of the process. Teaching someone is the best way to learn. I have some…
-
Would onePK be any relevant for CCNA? Anybody tried it? Alternatives to onePK?
A Google search for a Cisco IOS VM turned up a link to download onePK All-In-One virtual machine image but despite my further efforts to download it (creating an account with Cisco and rummaging through a pile of non-relevant links) I could not download it. It's announced as an end-of-life project on Cisco's DevNet page,…
-
I need some advice
In January I will be taking an accelerated 16 week course to get my CCNA R/S, this is at my local community college. I have passed my Network+ exam about 5 years ago and work a little with networking at work. However I am very rusty on my Network+ knowledge. So this is my question, should I spend the rest of the year going…
-
Subnetting Resources
I've been gathering resources to study subnetting with and figured I would share them: Binary: * Binary Number System * How to Convert from Binary to Decimal - wikiHow * https://learningnetwork.cisco.com/docs/DOC-1803 Subnetting: * Learn To Subnet:* A Free, Lecture-Based Presentation on IP Addressing and Subnetting (Only…
-
How to change IOS background in in Packet Tracer 7 from white to black?
Hi. I have just downloaded the newest version of packet tracer 7. It seems like the option to change the background colour has changed in Packet Tracer in CLI. Previously, in older versions such as Packet Tracer 6, I was able to change the background colour by going to Options>Prefernces>Font>Router IOS text. However, now…
-
Scheduled ICND2 before change
Finally bit the bullet and scheduled my ICND2 exam for Sep 9, mostly because I wanted to get it done before the version change. Starting to stress as I have not been able to lab much with my new job. I have been reading, rereading, doing flashcards, and going through some practice tests/questions. Think I have STP down…
-
should I but the cisco press command book ?
Should I buy the cisco press command book version 4 , I have version 3 for 100-101 etc now it is 100-105 and so on.I have the cisco press 100-105 study guide.
-
CCNA Security harder than CCNP R&S?
Hi. I am currently studying for my Icnd2 and hope to have to my CCNA RS soon. After getting CCNA RS, is it better to go for CCNP R&S or CCNA security? I have heard that CCNA Security is harder than CCNP and it's better to go for CCNP R&S before going for CCNA Security, since it's will be easier to understand after getting…
-
Safari Books
Hi All, I wasn't sure what section to post this in, so thought I would just post this here. Thinking about gettign a Safaribooks account, I have seen they do a 10 day trial - so I will probably give that a go. But wasn't sure what peoples thoughts were on it, do they have a lot of content and good value for money?
-
CCNA R/S in 4 months doable?
Is getting your CCNA R/S in 4 months doable? This would be through my local community collage, 2 months for ICND1 and 2 months for ICND2.
-
Multi Layer Switch Issue
I had completed a packet tracer 5.4.1.2 which used a 2960 switch but I was then instructed to change it to a multi layer switch. I basically did everything I had done using the 2960 but as you see in the photo I attached I am unable to ping the server from any of the PC's. I notice Vlan 99 was the 2960 switch but when I…
-
How to balance/prioritise pressbook, videos and labbing for CCENT/CCNA
Hi Guys, Im looking for help on a structured study routine. At the minute I prioritise reading, then videos then labbing and I think im not moving forward as efficently as I would like. I have been studying for about 3-4 weeks no and am just to start learning about NAT. I feel that reading the press book tires me out and…
-
Icnd2 Passed
Passed ICND1 last month and just passed ICND2 took about 5 weeks of very hard studying. I mostly used cbtnuggets (watched 3 times) and Lammle's book (read once). Overall I felt Icnd1 was harder for me, but this may be because I had never taken a Cisco cert before and did not know what to expect. Looking forward to CCNA…