-
Subnet practice site
There was a site called subnetskillz.com or something similar to that i used to use it when practicing subnetting. Anyone know there where abouts of this? has it moved domains? or is it just not active anymore?
-
Sdm
So, I have bin labing, going through CBT nuggets, train signal, ect ect. I can not find the SDM on cisco's website anywhere, populer rumor is that it is not part of the ASA line, not available for the standard router. Can anyone confirm or deny?
-
Root switch - bids in hexadecimal
Hi, I'm looking at a ICND 2 question that shows 4 switches. Their Bids/MAC addresses are shown as: 0013.8039.9500 0013.80d7.d580 0013.8030.5e80 0113.80c7.9700 Looking at the answer I can tell that 0013.8030.5e80 is the root switch. But I don't understand why this is lower than 0013.80d7.d580 or 0113.80c7.9700. Can you help?
-
IPsec Dynamic Point to Point Issue
All - I seem to be having a problem with my Point to Point IPsec setup. I am trying to set up my router to be the IPsec connection point for dynamic IPsec point to point tunnels. This is on a Cisco 1841 IOS: c1841-adventerprisek9-mz.151-4.M6.bin Config: crypto isakmp policy 1 encr 3des hash md5 authentication pre-share…
-
Config not saving...any ideas?
Hi guys, I bought a cisco 877 from ebay but it wont save my config... When I type copy running-config startup-config and it saves gives me the confirmation that is saved Router#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] Router# But when I turn my router back on…
-
RIP Question regarding multiple routes for the same network.
Correct me if I'm wrong, but if if a router running RIP recieves 2 advertisements about the same destination network from 2 different routers, it will use only the route with the lowest hop count and ignore the other until the shortest hop route goes down (for whatever reason). So what does a router do it if receives 2…
-
ICND1 and ICND2 Renewal
If I pass my ICND2, would that renew my ICND1 (CCENT) too? Also, to renew my ICND2 in 3 years, would I have to take a cummulative exam like the full CCNA to renew both of my ICND1 and ICND2, or could I just take the ICND2 again to renew them? Thank you in advanced.
-
Old CCNA exam using new material
Hello all, Im currently in process of renewing my CCNA as I had let it expire last year. My company has credits with global Knowledge and they currently only offer a bootcamp on the new CCNA exam. Im using conventional studying with the current/old ccna material (odom, cbt) and will use the bootcamp as final prepartion.…
-
Cisco Authentication Via IAS Radius Server
I have received many messages asking how to configure Cisco devices to authenticate with a Windows 2000/2003 Active Directory using RADIUS. So I figured I'd write this toturial real fast. Also this feature is more of a CCNP topic then a CCNA, so please dont attempt this if you are not fluent in Cisco configuration. To make…
-
Best Book to Study from for CCNA?
I'm looking for peoples input as to what study book they think would be the best for the CCNA 640-802. I plan on getting a lab kit as well. Through looking so far I've seen that people regard the Sybex CCNA book pretty well. Anyone else have any better suggestions, Thanks!
-
Passed CCENT..testing center was great
Passed the CCENT. Thanks to all on here with post of encouragement and guidance! My testing expearience was quite funny. Because I am taking this exam w/o the help and knowledge of my employer ( I want to roll in and slide my CCNA on the table of the boss one day), I had to take my exam on a Saturday. The Prometric center…
-
CiscoPress Premium Ebook Question?
I used Microsoft OneNote to take notes while reading books. Is it possible to copy and paste notes directly into OneNote from the premium Ebook?? Thinking about going the ebook route going forward.
-
T1 connections
Hello, I understand that T1/E1 CAS connections are typically used for data communications on a WIC interface card. However I see "WIC" labeled on modules with serial ports as well as modules with RJ-11 connectors. Are these the same T1 lines just with different connectors? Also, is one likely to see a VWIC module with a…
-
subnettingquestions.com
Can anyone tell me if the questions on this site cover the required subnetting expertise for ccent?
-
INE Podcast?
Anyone know how to find this on the ITUNES store or, elsewhere? Announcing the CCNA Audio Bootcamp Also, any other podcasts that I could use to prep for CCNA. I've heard of Packet Pushers, but I dont know if they have anything specific to CCNA.
-
Parts of PearsonVue Webstie are down
This has been down for the past couple of days. Guest its a sign from the Cisco Gods.
-
Broken network packet tracer files?
Anyone know if there is anywhere I can get these? Basically looking to practice troubleshooting by looking at a packet tracer lab that is "broken" and try to determine the issue and resolve it.
-
cisco exams
I'm taking my first cisco exam soon and was wondering if cisco questions were straight forward or if they were worded in ways to trick you? Is it "you either know it or you don't" or you could know it but be tricked into the wrong answer
-
RIPv1 and RIPv2
I've read up RIPv1 and RIPv2. Here is some idea I conclude myself. RIPv1 can and should use auto-summarization, which is on by default. RIPv2 doesn't need auto-summarization because each network command has both network address and subnet mask. And it should be disabled with "#no auto-summary". Am I correct?
-
What is the smallest subnet mask that can support 719 hosts?
What is the smallest subnet mask that can support 719 hosts? The answer is 255.255.252.0 can anyone here please explain to me how to get to this answer? I know that the number of host is= (2 to the power of the number of host bits-2) but I dont know how to reverse the operation. Thank you,
-
Recommended Rack Equipment for Labbing?
I recently order a Cisco rack equipment that can hold up to 19 devices heres the link - Cisco Rack FOR2500 2600 2610 2620 2620XM 2924 3524 3550 | eBay. I informed the seller that I would like to cancel but insisted on sending the rack. Will this be sufficient for me to build my CCIE lab in the future?
-
Phone won't register
Hey guys, I have two Cisco IP phones. They are the exam same model (7960) one registers and the other doesn't. On the CME I keep getting these messages from debug tftp events: *Mar 1 05:26:39.222: TFTP: Looking for CTLSEP00137F6BF9BD.tlv *Mar 1 05:26:39.247: TFTP: Looking for SEP00137F6BF9BD.cnf.xml *Mar 1 05:26:39.271:…
-
i need advice lol
ok as it says in my bio im 21 and i just made the jump to IT and i need as much advice as possible. I bought the A+ book and the CCENT/CCNA as well. And of course, i have absolutely no experience in the field yet and its getting harder to find places to get the experience needed, so maybe if someone could point me to any…
-
Is the CCDA worth the time?
I passed the CCNA on 12/24/2012. I took a small break and now I want to move on. I got the Cisco CCDA book and started reading it. The book just throws TONS AND TONS of info at the reader, seems a bit vague to me. There is a lot of stress on data center technologies, VPN, wireless, Core layer stuff. Sadly I am not using…
-
Different CSCO Numbers.
So I always used the same Pearson account for my exams. Today after passing the CCNA Security I noticed the CSCO number is not the same for my other certs. I sent a request to Cisco to have them merged or changed but has anyone had this happen. Did it delay your certs bad? or am I being over anxious right now :) Thanks.
-
STP question ?
In order to find our DP ports in a LAN segment we 've to calculate the cost to the Root Bridge The cost is the sum of the link speeds to the Root Bridge, Lets say the that i 've two switches connected together in Fa0/2 (1st switch) and gi0/1 (2nd) the cost of this link will be 4 or 19 I cant understand this concept
-
Anybody use IPExpert study materials? And how would you rate their materials?
I won't be using their materials for my ICND1 cert that I am currently going after...but has anyone used IPExpert study materials? If so, what was your insights on their materials? Thanks for any insights!
-
CCENT Only Practice Test
I am sure this has been posted before but I did not find it in a search. I am looking for practice tests for the CCENT only. All the tests I have seen are for CCNA. Any suggestions? Thanks.
-
curious IOS question
I'm sitting here messing around with a 3550 switch... Why does the IOS allow you to "attempt" to assign an IP address and mask to a switchport interface and then gives the message: "IP addresses may not be configured on L2 links" which I understand but why would the IOS even allow me to get that far? Why is it even an…
-
Which subnet does host 172.18.179.147 255.255.255.0 belong to?
Which subnet does host 172.18.179.147 255.255.255.0 belong to?I'm quite new to CCENT. I would be glad if any of you guys could help with a step by step approach how to arrive at the 172.18.179.0 answer.
-
A directly connected host can oing all ports on its router?
I'm doing Cisco Netacad Packet Tracer 2.3.2: Verify Connectivity of Directly Connected Devices. From PC1, I can ping router R1's ethernet port 172.16.3.1 and R1's serial port 0/0/0's IP 172.16.3.1, but nothing beyound R1's serial port. The study material says Ping from PC1 to router R2's serial port 172.16.3.2 "will fail…
-
Half-Way Through ICND1 and cannot meet ICND2 old exam deadline - what to do???? Help.
I have been reading the ICND1 Official Cert Guide and I'm now halfway through. At the current pace I'm going with my studies, I feel l will finish and pass the ICND1 v1.1 exam without issues. However, making the Cisco deadline for the old ICND2 v1.1 exam set for 30 September 2013 will be hard for me. What am I to do, I'm…
-
VOICE and DATA Characteristic
Hello guys, Above are the characteristic of voice and data What i don't understand from the voice is: * Smooth * Benign * UDP priority and from the data is:* Smooth/Brusty * Benign/Greedy * TCP Retransmits Can somebody explain these characteristics to me? Thanks in advanced
-
show VLAN command in GNS3
I need some help. I am using C3640 and C3725 images in GNS3 to simulate switches, but neither of these images seem to support the show vlan command. Other switch commands like spanning-tree and sh vtp status are supported. Has anyone else experienced this?
-
Best networking blogs?
What blogs do you guys read that are strictly networking? For VM stuff, Yellow Bricks is really good. Anything like that for network stuff?
-
Ipv6 RIP
Hey, I was going through the CBT nugget video on how to configure RIP for ipv6. In Packet Tracer, I followed Jeremy's instructions step by step but when I do "show ipv6 route", I don't see any RIP connections in the routing table and I am not able to ping the lan interfaces. I have no clue what I'm doing wrong. I cleaned…
-
CCENT Test This Morning at 9am
O'k I am off to go take my CCNET EXAM this morning. Wish me luck. I will post my results when I get home.
-
Static roue on ISP
What static route command on ISP will summarize all the networks (and only those networks) accessible through HQ? I have the above question from my study. The book answer is isp(config)#ip route 192.168.0.0 255.255.252.0 s0/0/0 But 192.168.x.x are private IP that can't be routed or used in the Internet, right? If so, the…
-
Dhcp scope
Hi all, i'm preparing for CCNA ICND1 exam. I read about configuring the router to provide DHCP IP Address to clients, DNS Server, Def Gateway & Excluding add on the ROUTER Is there any way to define scope on the router e.g. DHCP SCope = 192.168.1.20 - 192.168.1.100 Excluded Range is 192.168.1.1 - 192.168.1.10 DNS Server =…
-
Passed 640-802 with a 960
Very happy to report that I passed the 640-802 exam today with a 960 and I am now a CCNA! I was originally preparing for the ICND2 exam but a friend gave me a free voucher for the 640-802 exam. Anyway, here is what I used to prepare in order. 1. Todd Lammle 7th Edition book. 2. CBT Nuggets 3. Boson Netsim labs (Paid…
-
RIPv1 doesn't supprot subnetting?
Is it correct that RIPv1 does not do subnetting? The smallest network utilizing RIPv1 would require a class C ＩＰ domain, right? I get this idea because it says the network command would assume the subnet mask by checking the netowork IP entered. And the smallest network IP that we can enter is a class C IP address.
-
CCNA NetAcad Hands-on Lab 1.5.2: Help needed to understand
I'm doing CCNA Basic Router Configuration Hands-on Lab 1.5.2. At the end of the lab, I can't ping 192.168.3.1 on FastEthernet0 on R2 from PC1, which is fine. However, while the procedure Step 7 (listed below) says I shouldn't be able to ping R2 from PC1, I can actually ping router R2's serial port (192.168.2.2). Why? From…
-
DHCP not working when NAT is enabled.
I have the following scenario. I have two lans separated by three routers. LAN A contains a host and LAN B contains a DHCP server (WS2K running the DHCP service. I have Router A configured with a helper address so that my LAN broadcast for DHCP are sent to the server on the second LAN. This works when I do not have NAT…
-
How to enter the Network command for RIP v 1?
When entering the network commands for RIP v 1, do we just enter the connected networks for each router? For example, for the network in the diagram, we enter "network 192.168.1.0" and "network 192.168.2.0" on R1 because they are connected to R1. we enter "network 192.168.2.0" and "network 192.168.3.0" and "network…
-
Hub and Spoke Address schema help
Wrong thread title
-
CCENT vs CCNA material
ok, did a search and didn't fine a thread that I could ask this question without hijacking one. So I am sorry ahead of time if I am doing this wrong. I just got Todd's Lammle's CCNA study guide 7th edition. I am shooting for CCENT in a few months then trying to squeeze ICND2 in right before Sept 30th. I have also started…
-
New ICND1 and ICND2 exams
I've been reading that Cisco has changed the CCENT(ICND1) exam. I also see that there is a new CCENT series of CBT nuggets. Does the same hold true for the ICND2 exam? Just curious as I do not see a new ICND2 series on CBT nuggets, only the ICND1. Also, does anyone know of any books that cover the new version of the ICND2…
-
Copy flash tftp when IOS image is in a folder
So I got this switch and I want to back up the IOS image. Every darn place explains how to do it when the IOS image is in the root directory in flash, which is pretty simple. But mine is in a directory called flash. When the prompt asks for the file name I typed flash/longname.bin and a bunch of combinations without…
-
Well, just went ahead and scheduled ICND1
I've spent 2 months studying. Every single night for hours, even weekends. Used Odom's book, simulators, practice exams... you name it I tried it. I feel like I'm going over everything that I already know. Took an assessment on Cisco's sight and I scored over 90% on it. The practice tests that I took where I didn't score…
-
GRE Tunnels
I get that GRE tunnels are great for transferring routing protocols, as of the broadcast/multicast feature. Was wondering what else they are used for in the real world. Has anyone got any real life examples that will just help me clarify? Thanks Dan
-
Which mechanism can be used to avoid a count to infinity loop?
Which mechanism can be used to avoid a count to infinity loop? a. split horizon b. route poisoning c. holddown timers d. triggered updates e. split horizon with poison reverse I pick B. route poisoning, because it marks the route hop count as 16 (unreachable). Am I correct?
-
How to best make use of these routers?
Hi everyone, I'm a long time lurker here, but this will be my first post. First off thanks to everyone here for making this site what it is. It was instrumental in getting me through the process of getting my A+ and Network+ Certs. I'm currently studying for CCNA. My work was getting rid of some old equipment this week and…
-
ICND2 Question - No IP Subnet-Zero
Hi Everybody, No Zero Subnet seems easy but has some tricky aspects. As in i get thrown off by trick questions easily. Im sorry to ask this way, but can someone spell out how No IP Subnet-zero really works? Thanks
-
ACL with BGP community polices
access-list 101 permit ip host 6.6.6.0 host 255.255.255.0 OK I know what it does by why is it written like this ?? this read like " any traffic from the network address to the subnet address" Why not just have it as a standard access list that covers the whole subnet ?? Does any one have any more info on this format of…
-
EIGRP Question ???
I cannot understand this question so if you can help me i would appreciate. Based on the topology table that is shown and assuming tha variance is not configured which route or routes should appear in the routing table ? R1#show ip eigrp topology IP-EIGRP Topology Table for AS(100)/ID(192.168.8.21) P 192.168.2.0/24 1…
-
CCNA, Pass Without Books?
Hello everyone. I'm considering starting on the path to study for the CCNA. I currently have Network+, but CCNA seems like an attractive certification. I was considering this before but I've fallen away from it for quite some time. My question is this. Do you guys think it's possible to study for the CCNA with only…
-
Subnetting question ???
Can you please help me with the following question How many subnets can be gained by subnetting 172.17.32.0/23 into a /27 mask, and how many usable host addresses will there be per subnet A. 8 subnets 31 hosts B. 8 subnets, 32 hosts c. 16 subnets 30 hosts D. 16 subnets 32 hosts E. A class B address cant be subnetted into…
-
NTP Server - Not syncing
Hi all, I am trying to setup a Cisco 7200 as an NTP server, well it is getting its time from our AD server which is pulling it from the internet. The config on the router is ntp authentication-key 1 md5 075E711D6B5C3D5134472F58537E7B7109666C7747574F54580608 7 ntp authenticate ntp trusted-key 1 ntp clock-period 17179568 ntp…
-
"erase nvram" and "erase startup-config"
"Erase nvram" and "erase startup-config", do these two commands do exactly the same thing? Do we have to issue any other commands to get rid of more things to re-configure a route?
-
Straight to CCNA or CCENT first?
For someone who already has passed Network+, would you recommend they still go the CCENT -> CCNA route or can they just go straight CCNA after Network+?
-
ICND2 Question - Enhanced ACL practice?
Hi Everybody, Can anyone recommend a tutorial, or youtube, or practice website (in the style of subnettingquestions.com) for enhanced ACL's? These things are killing me. Any advise or support would be greatly appreciated.
-
640-554 down!
I just got back from the testing center and passed the Cisco 640-554. Today was the last day in my term for WGU to take the test for my class. I really enjoyed studying for this cert, and agree with some others that it leaves you hungrier for more. After my GCIA and GWAPT studies I will focus on CCNP : Security. I ended up…
-
Weard networking
I'm doing some Cisco lab. The computer I'm using now has two NIC. One NIC is connected to the Internet (Cable Internet) so I can post here:). The other NIC (192.168.1.10) is connected to a Cisco 2950 switch. The Switch is then connected to the FE0 on Cisco 1750 router (192.168.1.1). The router was wiped clean with "erase…
-
ICND2 Question - Native VLAN vs Default VLAN?
Hi Everybody, I may be over-thinking this, but I am also worried that I am misunderstanding something: Is there a difference between a 'native vlan' and a 'default vlan'? Thanks for your answers.
-
Old Ccent exam vs New/old Cbt nuggets
Hello there TE :) I am studying for the Ccent exam (the old one), I have the Lammle 7th edition book but would like to have some video traning aswell. Tried the Free INE ones, but don't really like it. CBT just released a new version of their CCent training, but that is for the new exam. Should i get the old version or can…
-
Passed ccna!!
Whew! 958/1000! Glad that's done! Tough!
-
Cover all CCENT Practice Labs
Hi all, i approaching to go to ICND1 certification. I prepared some theory exams with score between 78 and 82% aprox. I must improve that. But I think that I have to make more labs. Can you tell me all labs that i have to do to approach pass this exam. I make lab about: cdp, rip ,backup IOS and configuration, some…
-
About Summarize Static Route...
Hello, This is my 1st post :) I am summarizing (5) Networks with the ff. IP's a=10.19.32.0 b=10.19.48.0 c=10.19.40.0 d=10.19.56.0 e=10.19.57.0 Binary's a=00001010.00010011.001 00000.00000000 b=00001010.00010011.001 10000.00000000 c=00001010.00010011.001 01000.00000000 d=00001010.00010011.001 11000.00000000…
-
Most difficult problem you've fasted as a ccna?
For those of you that have your ccna, what has been a difficult problem/technical issue you've come across when something wasn't working right? How did you go about fixing it? (side note below) Sounds like an interview questing, but I am just wondering what im getting myself into. once im done with ccna i plan to read…
-
Subnetting Refresher
Subnetting a Class B Network that would allow for at least 510 hosts per subnet. Write out my Binary… 512 256 128 64 32 16 8 4 2 1 I use the 256. 2^8 so I borrow 8 host bits = 256 minus 2. New mask is… 255.255.254.0 or a /23 I believe I am 100% up to here… Now I wanted to see what IP address I can use… 172.16.X.X Please…
-
Cisco ASA License question
Hello fellow TE members.I have an ASA 5505 with the base license. I would like to upgrade to Security plus license, but I believe it'll cost me quite a bit. I cannot seem to find any additional information on Cisco's website on how to upgrade it. My ASA is running 512MB RAM and 128 Flash.Thanks in advance.
-
Student budget network diagram
Hey, So, I am looking to diagram my network, what do you guys use? I am looking for free or open source. John
-
Working towards the CCENT
Hello, I have been on and off with my CCENT studies and due to a recent injury in the family I had to place it on the back burner. After a month or so of being completely out of the loop I discover the exam changes. So starting tomorrow I am goingto to start fresh and try to get it done by September. I have two little kids…
-
1760 Router only shows ASCII characters on boot.
Not sure what has happened with this router, last time I turned it off it was working fine. I have tried to break into ROMM and it keeps displaying the ASCII. I have tried ctrl break and Puttys special commands break and it does the same thing...just provides me with some more of the same characters. Basically it displays…
-
Confused big time
Hey Guys, First of, awesome Forum and awesome website full of support and guidance... I am really confused as the new exam is announced. I have been studying for CCENT for a month now. I have gone thru CBT Nuggets, Wendell Odom's CCNA ICND1 640-822 and have been practicing labs in packet tracer. I was all set to give my…
-
Classless routing
I'm trying to understand better about classless routing. In classful routing, we have class A, B and C IP addresses with their pre-determined subnet masks. That's easy for me to understand. In classless routing, since we always have to give subnet mask with its IP address, can I use subnet mask 255.255.255.0 with a network…
-
Georgia Tech is offering a free online course in Software Defined Networking (SDN)
https://www.coursera.org/course/sdn
-
STP Designated Ports
Hello all, I've started reading Wendell Odom's ICND2 book and have a question about designated ports. Actually, it's more of a clarifying question, but a question nonetheless. I think this diagram might be confusing, but I'm going to try anyway. Switch A--Switch B--Switch C--Switch A (Imagine that this is a triangle and…
-
CCNA lab
Can anyone tell me if this is a good setup for a Lab? i don't want to spend money only to realize that i made a mistake. I will not be taking the exam until around june/july.* ONE Cisco 3600 Series 3620 Router having 16MB Flash, 64MB RAM, 2 Ethernet, 1 Serial Interface * TWO Cisco 2500 Series 2501 Routers having minimum 1…
-
WIC 1DSU T1 vs FE 10/100
Good evening, I am slowly assembling my lab, my first router has a WIC for a 1dsu T1. What exactly is that? How does it compare to the standard FE port. How is this going to affect me creating and getting up my lab. I am expecting another router of the same type soon. Then I have a 1841 in possesion but it has no cards,…
-
got lab equipment... what next??
Ok so I have the following lab equipment and I'm not sure where to begin. 831 router 1721 router 2621 router 3550 layer 3 switch 2x 2950 switches vpn concentrator I have been studying for CCENT off and on for a year and done some labs with packet tracer. Now with the new deadline I am kicking it in 5th gear. I don't…
-
CCDA/CCDP vs RCDD
Hi, all- I've been discussing BICSI and Cisco certs with some co-workers, and I'd like to get some more perspectives. Cisco's graphic here: https://learningnetwork.cisco.com/docs/DOC-13157 shows that the RCDD is more or less preliminary to the CCDP. From comments I've heard, it sounds like the RCDD is more grueling than…
-
Passed ICND2 with 960 marks
ICND2 was completed about 2 hours ago. Got 960/1000. I took ~55minutes to complete the exam. Questions were easy, and I don't know how the remaining 40 marks were gone. Next step? CCNP R&S. Preparation time: 25 days to be exact. Prep materials: 1. Odom's official guide. 2. Lammle's guide. 3. CBT Nuggets video series. 4.…
-
101 Labs for CCNA book question
Hello all, I want to know if anyone has experience with this book, I am looking for a lab book to use that will not only tell me how to setup the lab but also what commands to use, i looked at the preview and it gave me each lab but doesn't seem to give the solution, does anyone know if this books comes with the answers?…
-
Time between ICND1&2
How long after passing ICND1 should I go for ICND2? My current rate of study is 2-3 nights per week (3 hours ish) and all day 1 day at the weekend (8 hours). I passed N+ in 1 month study and ICND1 im doing about a month also. Is ICND2 much harder? I just got 710 in a boson test for ICND1 after 1 week study so I'm confident…
-
show frame-relay lmi interpretation Lammle´s book page 776
Hi all In Lammle´s book (7th edition) at page 776 shows the output of show frame-relay lmi command. Among others Num Status Enq. Sent 61 and Num Status msgs Rcvd 60. Below this output says: Is the frame relay network working? No, because the router has sent 60 inquiries and has not received even one reply. So is this a…
-
CCDA to become CCNA:Design?
I just wonder if they're going to eventually rename the CCDA to CCNA:Design. Look at the last example: CCIP (Cisco Certified Internetwork Professional). It's now CCNP:Service Provider Is there a reason why the Design track is the odd-ball of them all? Maybe they're going to be overhauled sometime in the nearish future?
-
Access list and Static NAT ?
Hello there. If I have a router on which is applied a static NAT for the inside host A to reah the oustside networks and I want to deny outside hosts to reach host A which address im I supposed to add in the access list? The inside global or inside local? What is the differene?
-
Free INE CCNA videos
INE is offering free access to their CCNA course for a limited time when you sign up. Sorry if this was posted already. I'm at work and didn't try to search. http://www.ine.com/self-paced/ccna/bootcamps.htm
-
Discount on new and existing CCNA/CCENT Exam Material
30-45% off for the new and old books isn't bad: About CCNA > Customers and Markets
-
Sorry for the noob question but...
Hi All, So I have just started to go through CBT Nuggets, the first step on my path to CCNET/CCNA. I am really enjoying it so far and I'm about put a lab put together at home, I'm starting to acquire some switches and routers from ebay, just waiting on delivery :) . Im just wondering.... How/what do you plug in to your…
-
How to connect two Cisco 1721 router together?
I finally start to mess around my Cisco hardware purchase. I'm doing Cisco NetAcad Lab 1.5.1 Cabling a Network and Basic Router Configuration. I have two Cisco 1721 routers. Each router has a T1CSU/DSU WIC installed. With the "Show ip int br" command, R1 shows: R1(config-if)#do show ip int br Interface IP-Address OK?…
-
Cisco 1751-V vs. 1760
I saw these two routers for the same price. I'm currently working on my CCNA: R&S. But, even if I don't decide to get CCNA: V, I would like to have something that I can experiment with voice on and still use for CCNA: R&S. This would be [as best I can tell] either a 1750 Series, 1760 Series, or 2800 Series for routers and…
-
Trick question? Wlan bands.
The 3 bands in 802.11 are 900mhz, 2.4Ghz and.....5.7Ghz? I would assume it would be 5.0Ghz but 5.7Ghz crops up sometimes. Could anyone shed some light on this? Kai.
-
Why are remote networks shown differently in route table?
I'm doing Cisco NetAcademy Packet Tracer activity. My question doesn't have anything to do with the activity, but why are the static routes for two similar remote networks, 192.168.4.0 and 192.168.6.0 are shown differently? S 192.168.4.0/24 is directly connected, FastEthernet0/1 S 192.168.5.0/24 is directly connected,…
-
CCNA with experience or CCNP without experience?
Hello everybody need your advice again. Currently I'm working on my network+ and also CCNA odom book .My question is having two associate level certificates like ccna r+s and ccana security with several months experience are more likely to lead a job or one CCNA r+s and CCNP R+s with zero experience? I ask this because in…
-
NEW CCNA Exams Announced!!
Cisco probably inadvertantly put on the CLN network last night that the new CCNA tests start March 26th and the current tests expire September 30th! (see attachment).... If you're studying, you need to get with it! The new ICND2 test number went from 640-816 to 200-101....weird. I've heard that the CCNA will no longer be a…
-
Hello Everyone
I am not sure if I am in the correct area but I am working on my CCENT and had a sample question and answer that I cant figure how to solve it, any help would be greatly appreciated..:) What valid host range is the IP address 172.30.98.55/23 a part of? Answer: 172.30.98.1 through to 172.30.99.254
-
Prep for the CCNA in 4 weeks
Hi all. I really need your advice, guys. I've already finished reading two Odom's book and I've done few labs on real Cisco equipment and GNS/CPT. I decided to use some of the sites for training questions. And I think pass CCNA after 4 weeks. What do you think about it? Is there enough time?
-
How hard actually is ICND1?
I have my test on 26th April. I have just passed Network+ and have been studying for 2 weeks on ICND1. My plan is another week and a half on the books then the remaining week and a half pure labbing and maybe CBT nuggets (although I really didnt get on with them in N+). I feel like I'm maybe hyping this up to be something…