-
GNS3 + hardware switches
The youtube and other forum posts are from over a year ago... so pardon if I'm just re-making more threads of the same... BUT!! I've been SOO excited about this Lab solution that I can't stop thinking about it!! =D GNS3 + 3x 4port PCI network card -> connected to real Cisco Youtube: CCIE Lab using GNS3 and Quad NICs for…
-
Icnd2
Tomorrow I am taking the ICND2 for the second time. I was soooooo bummed I failed the first time but have been studying up on ACL's and STP. Wish me luck!
-
CCENT 2 Study time
Passed CCENT 1 last month and havn't really had chance to crack on with Numero 2. I had planned to do the exam on May 1st as Im due to go on Holiday afterwards. This is only 6-7 weeks away. Will it be possible to gain the knowledge in this short period of time to pass the exam? Thanks in advance guys
-
Frame-Relay Lab
Configure R1 as a Frame-Relay switch. In this lab R1 will be configured as a Frame-relay switch so no IP address is required. Turn on Frame-Relay switching feature on R1: R1(config)#frame-relay switching When I enter this command, I receive an error. R1(config)#frame-relay switching ^ % Invalid input detected at '^'…
-
Routers with ios 12.3
Hey all, Looking at a few routers on eBay, current cheap and end in 15 hours. 1* 2620xm, 4*2501,1*2514. The 2501 and 2514 can only run IOS 12.3. I'm not sure how much of a big deal this is for CCNA/NP level. Anyone have any input on this? Thanks in advance
-
Passed ICND2: Couple questions on what to do now?
Good afternoon, I passed my ICND2 earlier completing my CCNA . Very glad to have the CCNA behind me! Nevertheless, over the past days I have been contemplating what I should do next. I currently work doing level 2 help desk with no networking job duties. I have been debating a few options: 1. Carry on towards CCNP ( This…
-
Passed 640-553 yesterday
I did extremely well... only missed a few questions. I definitely recommend anyone considering it to take it before it's replaced by the 640-554. I used GNS3 with SDM for labbing (it was a nightmare... .my advice would be to install it on xp and use an old version of java). I also used the cisco press book from Catherine…
-
Class B subnettting
Here is a question : Given a class B network of 155.44.200.0, what mask could be used to provide 15 networks each supporting 120 users : A 255.255.252.0 B 255.255.248.0 C 255.255.240.0 D 255.255.255.128 E 255.255.255.240 The correct answer is "C". But i think option "A","B","C"and "D" are correct Because if i want 15…
-
What would be the best all around router for my lab?
So I'm well into to studying for my CCENT and am following what a few members have posted here and which ties into WGU's recommened study course also... watching supplied videos from WGU (take a ton of notes) learn subnetting CBT Nuggets (take a ton of notes) learn subnetting read Odoms 3rd edition learn subnetting lab,…
-
Question about the New CCNA wireless Exam!
Hi Guys! So I read on cisco website that there is a new exam start on May 2012 (Exam:640-722) , and they have a reference for the update subject only. Should I use the (study guide for Exam:640-721) first and read the update ? bcoz the update reference is only about 150 pages! Thanks in advance! :)
-
Quick OSPF Question
The output is in my production network. Quick question, I'm right in thinking that packets to the 125 subnet will go equally through each of the available routes? Would you agree? O 192.168.125.0/24 [110/2] via 192.168.224.131, 1w1d, Vlan800 [110/2] via 192.168.224.130, 1w1d, Vlan800 [110/2] via 192.168.224.129, 1w1d,…
-
Free Online CISCO router simulator
Hey folks- Question for ya... Are there any online CISCO router simulator like the one on this website? I wanted to practice some commands for my ICND1/ICND2at work and I can't bring my own laptop at work to do so. I like the TechSim on this site but it only has 1 lab and that's it.... By online I mean that you do…
-
CCNA vs ICND1/2
Seriously on the fence about just going straight CCNA, rather than an extended focus on the ICND1 then 2. Anyone taken this route? I like the idea of it, as you're only sitting one exam (if you pass) of around 50 questions instead of two for the same end result. Is it beneficial to have a CCENT? I'm not trying to decorate…
-
Subnetting question
What is the broadcast address of the network 172.25.236.0/23? Answer: 172.25.237.255 I dont get it. is a class B address so 23-24 = 2^1 = 2 so 2 host per subnet subnets = 128 So it will 172.25.36.2 I am doing something wrong but I cant tell what it is. help me here.
-
Vlan and subnet
Suppose I have 3 computers namely A,B and C. These 3 computers are attached to a Layer 2 Switch (switch has no layer 3 capability).I assign Lan 1 to Computer "A" , VLan 2 to "B" and VLan 3 to "C". First question : If i place the 3 computers on different Vlans , do i have to give them separate sub nets also ? Is it possible…
-
ICND2 just crushed me...
I know these posts are a dime a dozen but here goes: I just took ICDN2 and was demolished... 610. I really believed that I was prepared for it and looking forward to ace-ing it with ease. **I have to admit, I prepared quite a bit and was posting 850+ on the Boson Exams the day before the test. It seems to me the actual…
-
Adsl module and Internet connectivity
Hey guys, Im thinking of buying an adsl module of my 2600 router and was just wondering what I would need to do to set it up? Im guessing security would be an issue as I wouldn't have a firewall?
-
Help: Stp, rpvst, portfast
Hey i am just a little bit confused here. RPVST is supposed to cut down on the the convergence time of switches whenever there is a change in the topology. how much time would be saved here with only RPVST enabled as compared to enabling rpvst along with portfast? i am really curious as to how portfast work along with…
-
Practice tests for ICND1
Where can I get practice tests for ICND1 that are NOT brain ****? Thank you,
-
6500 Useful for a CCNA Lab?
I may be able to get my hands on a 6500 series device, will this be useful for a CCENT/CCNA lab? Price tag of $100 seemed like it was a good deal. - Jinuyr
-
RIP-Frame-relay-Split-Horizon
Will I have to disable all split horizon rules on all routers in a 3 router point-to-multipoint running over frame-relay? Or should I just disable the split-horizon on the spoke router (on R1 that connects to both R2 and R3)? If I enable on all will RIP loop?
-
Check out the website subnetonline.com
Looks like a great website recommended by some IPV6 videos I was watching… It has Online subnet calculators, network tools, ipv6 network tools, converters, tutorials, references and downloads. http://www.subnetonline.com/
-
Subnetting
Check my subnetting. 126.0.2.99 /24 Net ID IP: 126.0.2.0 1st Valid IP: 126.0.2.1 Last Valid IP: 126.0.2.254 Broadcast IP: 126.0.2.255 155.44.2.2 /21 Net ID IP: 155.44.0.0 1st Valid IP: 155.44.0.1 Last Valid IP: 155.44.7.254 Broadcast IP: 155.44.7.255
-
Most complete Subnetting method?
I've been off and on this forum for a while but I was just wondering if someone could suggest the most COMPLETE subnetting method. I've seen a lot that seem to be more advanced or they dont cover the basics and leave out a lot of stuff. I have the Todd Lammle book and CBT nuggets. I am currently preparing for CCENT. I have…
-
100Mbps LAN dropped to 10Mbps?
A LAN uses 100Mbps. However, a broadcast performance test tool shows the bandwidth is just about 10Mbps for UDP packets. If the sending speed exceeds 10Mbps, lots of retransmission are seen. Is there a way to troubleshoot the issue on switch? I was told the internet connection is capped by 1MB/s for this LAN. I'm not sure…
-
can't ping e0/0 on a AS2509-rj
I connected a transever 210T to the AUI Ethernet, then configured my interface but i can't ping it.
-
Copying from tftp
Hey guys Trying to upgrade my 3550 IOS image. I've downloaded solar winds tftp server and put the image in the correct folder. On the router I've assigned vlan1 ip of [URL="tel:192.168.0.50"]192.168.0.50[/URL] .. My computer is 0.100 They can ping each other fine. Well I try and copy the file over though copy tftp flash…
-
Starting with Packet Tracer
Hi, Been on the site a short time, and now finally getting to some fun studying for ICND1. I am NOT a test guy...in preparing for previous tests, I had to study for months before I was comfortable getting into a test environment. I am eager to get my CCNA, and this forum has paid me in spades with information, and…
-
which 12.4 IOS to use on a 26_ _ xm LAB router
I just loaded c2600 adventerprisek9-mz.124-19 to FLASH: because i was told we need a version 12.4 IOS. This is a 29meg file and boots forever, and, ever and, ever; god forbid i have to do a reload cause i screw things up. Can we use ipservices or a security IOS and get all the commands that we need for all our lab work,…
-
Ccna - 2610xm
Hey guys, Lurker here and decided to get a bit more active.... anyway ive been offered 3 * 2610XM with maxed memory 32/128 for about £130/$200 and was wondering whether this would be what i need for the lab im building, i already have 2 * 3750 so i dont think i need any more for now, will probs pick up 2 * 3560 when…
-
error oprning tftp but i can ping back and forth
i just installed tftp x64 free by ph.jounin. I connected pc NIC to my 2651xm fa0/0 with a cat 6 cable. in my pc GUI i selceted LOCAL AREA CONNECTION\properties\ipv4\properties. I selected use this IP address and put the ip 192.168.200.7/24 gateway of 192.168.200.2. I configured my 2651xm R5(config)#int fa 0/0…
-
Scot Morris CCIE Quote
- Scott Morris on Packet Pushers' podcast They were talking about how being an Expert you still get to say, "I don't know." However, you also know exactly how to follow up and find the solution. Show 109 – Knowing Why – Cisco Certification Roundtable from CLUS 2012 (great podcast btw =p makes networking world seem a bit…
-
God, is the CCDA really this bad?
So ive decided to take the DA/DP exams in relation to my current situation. I bought the Bruno cert guide and are about 75% through. So far, the material is mainly trash! I feel it focus's on jargon, buzzwords and a lot of the Cisco product line / Marketing rather than the important facts of design work i was expecting.…
-
CCENT to CCNA
Hey everyone, I was just curious how long it took for you to go from your CCENT to your CCNA. Also what are some books everyone has been using. I'm almost done with Todd Lammles 7th Ed and am looking for something else. I also have CBT Nuggets as well as Train Signals CCNA vids.
-
ccent
Hello everyone i am new to cisco and i plan to write the exams soo i want to know how long it toke you guys to write your ccent cause thats what i plan to take first and also can someone help me with a Boson Exsim i can not get to buy that online here in africa thanks alot guy. stay blessed
-
My 2507 Router
I want to know what kind of work/study I can do since I brought a 2507 router from eBay? I also received the console port and USB to COM converter today and look to purchase two more routers and one switch in the coming weeks. Thanks.
-
AIR-AP1131AG-A-K9 enabling the radios
hey i'm trying to enable the dot11 radios on AIR-AP1131AG-A-Kt but cant seem to get it to work. On the cisco box has yellow sticker stating RADIOS OFF BY DEFAULT disabled after 12.3(4)JA. Its not showing the radios in the sh ver or sh inv raw. I tried to go into global config mode and enable the interface typing :int…
-
where do you read update about networking technology?
where do you read update about networking technology? I want to be up-to date with regards to networking but can't find a good site. thank you!
-
need some recommendations for my lab
after passing my ccna i took a year break to handle some things. Now i am motivated and I need help building my lab. currently, I have 2 3500xl switches and a dell power connect 5212 and I need recommendations on cisco routers My plan is to have the devices to help me get through ccnp
-
ccna simulation
hi anyone has got the ******** CCNA 640-802?
-
How to configure t1 connection
Is there some video series that explains how to configure a t1 connection. I know in ccna studies explains how to configure serial lines and clock rates. Is there one that explains how to configure t1 like in the ccna voice or something else.
-
Need help with configuring a 2811
For who ever helps I will be forever grateful. I have to set up a 2811 to work with a 2504 Wireless controller, 6 ap's and 3 SSID's. Going in a home so really doesn't need to be perfect. So far I know I set up 3 vlans, g0/0.1,.2,.3. Set up the dhcp scope on each and enable nat. The switch is a 2000p. I will set two ports…
-
Static Routing using GNS3
I want to use static routing to configure the above topology .My queries regarding it are : Q1) When i am configuring static route in SALES2 for say 192.168.10.0 ,192.168.20.0,192.30.0, 192.168.40.0 , 192.168.50.0 will i use 192.168.60.1 (IP of interface in SALES2) or i will use Fast Ethernet 0/0 , as outbound entity.…
-
Cisco Support Community website down!
Cisco Support Community is undergoing maintenance and is temporarily unavailable. Starting, FRIDAY, July20th 5:00pm (PST), we will be migrating the Support Community Site to a new locale. THIS IS A SIGNIFICANT OUTAGE - lasting approximately 20 hours. Please return to the site after 2:00pm (PST), Saturday, July 21st!…
-
USB to RS232 adapter
Hi, I have got one of these adapters, going to be using it from monday onwards but I havent got any cisco hardware to do a dummy run before then. Does anyone have any experience with these? This is what I get at the moment. Drivers have installed correctly, when I plug it in it appears in 'device manager' like so: Ports…
-
ICND1 passed!
I just recently joined this site and just wanted to say I just passed the ICND1!
-
CCNA exam Voucher
HI , Please can anyone help me with this . I live in UK and would like to book a exam date and pay for it . however it seems iam in USA site and th eprice is with dollars? is that normal? also i want to buy voucher do you think with voucher is cheaper ? any one had thsi eaxam in uk can you tell me how much in pound you pay…
-
Static Routing
While we configure static routes in a router , we can use both a INTERFACE name like s0/1/1 Or an IP Address as the next hop entity(outbound).I mean in the syntax <R1-config>ip route 192.168.0.5 255.255.255.0 X , I am refering to "X". I understand that usually "X" is set as interface if serial point to point link is used…
-
Spanning Tree BID Tie Question
Hi Everyone, I recently started studying for the ICND2 exam and have checked in on this forum from time to time. I always enjoy the people/answers. So I've decided to make a post and get more involved with the community here. I just finished studying STP. As you know STP uses these 4 conditions when making decisions. 1.…
-
Stuck in a LAB
QUESTION Refer to above network diagram You are the network administrator at Ranet, and have to config the router "Ranet-BR" via Console Terminal as below: Task 1. enable interface Se0/0/0 and set IP address /Subnet Mask that can connect with router "Ranter-HQ" at 192.168.0.254/30 Task 2. enable interface Se0/1/0 and set…
-
ICND1 subnetting question that i'm not completely understanding, HELP? :)
Morning All, my first post and hello to everyone. Q1, In the book, ICND1 Official Exam Certification Guide by Wendell Odom (2nd edition), i'm struggling to grasp the understanding of the following question in Chapter 12 (question : Which of the following subnet masks let a Class A network have up to 150 hosts per subnet…
-
Labs
Is there anything available that will walk you through different scenarios. I the M$ world there are plenty of options starting you from the beginning and then working you up to more advanced settings... basically step 1 we are doing this.... 2 now we are going to do this 3 we will now do this 4 xxxxxx thanks,
-
Pearson VUE "Cisco ID: ID Pending"
Hey Guys, I just wanted to sign up to take my first Cisco Exam next Friday the 27th of July, but I can't seem to book a test because I don't have a Cisco ID yet. Does anyone know how long this process will take? I really need to take the test on or before that date since I am moving cross country and want to have the CCENT…
-
Good CCENT/CCNA Lab?
First off, I have absolutely no experience whatsoever with Cisco equipment. I only have my A+ and Network+, so just basic, basic stuff. So when I look at all these certification kit sites/threads I'm always lost when people favor one model or version over another. Money isn't a huge factor, I'm just looking for a lab that…
-
Fully qualified domain name
Well i have read about FQDN in a couple of books and websites but i am still un able to understand that what is its advantage ? Secondly is domain-name command in Cisco IOS related to it as well ?Kindly explain in simple terms .
-
Overhaul of CCNA Voice?
From what I have been able to gather from google the CCNA Voice was recently redone and there are no plans to redo the cert in the next year or so like CCNA Security. Is this information correct or is there something I missed and the cert will be redone soon?
-
2900/3900 series routers demo licenses
Does anyone know how long the demo licenses last for? Note: There should be a general cisco section for non certification questions.
-
ICND1 Test tomorrow!
Hey guys, long time lurker, first time poster. A little background on me, I have my Net+ and Sec+ knocked out, and I took the composite CCNA exam 3 months ago and failed (badly I might add, 643/1000). Got a promotion at work that gave me a little bit more money and a lot more responsibility, so I thought scaling back to…
-
I need some motivation of some kind
I have a secret. I haven't touched my CCNA book in over 2 weeks. I am half way done with it, but I have lost the fire that I had. Anyone got any secret to keeping that motivation going in a motivation-less world? I use to dive into my book and just read the hell out of it, I was at a going rate of a chapter a day and…
-
confused in IP and UDP question!!!
hi guys, im confused in this question,which one of these deliver the best effort delivery of user data?! UDP or IP? some say UDP some say IP is the answer of this question ,i want to know which one an why? Thanks.
-
How does routing work?
So what is routing anyways? Yeah, it's a review for some, and might be a new concept for others. Either way, it's important and a generic :)
-
Can I create a TACACS+ server?
Just starting out on the CCNA Security Track, thought it might be the best option before the CCNP, I'm looking to set my lab up with a TACACS+ server, but after trawling the net I can;' seem to find anything solid on the type or brand to use. Does anybody use a TACACS+ server? And can anybody guide me in the right…
-
Comparison 2500/2600 Switches for CCNA
I am trying to shop around for switces to start working on them for my CCNA. What are the key differences if any between them? I am looking to create an environment that can be used for the CCNA, CCNA Security/Voice, and CCNP. What series of switches should I buy if I plan on getting all of the above certifications within…
-
Access layer to Distribution layer connection and thoroughput
Hey guys, Currently studying for ICND2... This is not a question that seems as if it will be covered this is more of... when I get into something I start wondering about how it works so here is my question... You have access layer switches with end users between 250-500 users... and they feed up to distribution layer…
-
Cabling Query
Pin Color Function Pin Color Function 1 White/Green TX+ 1 White/Green TX+ 2 Green TX- 2 Green TX- 3 White/Orange RX+ 3 White/Orange RX+ 6 Orange RX - 6 Orange RX- Above shown is a table of a cable with pin configuration of the two ends given on left and right side .Well according to a writer it is supposed to be a straight…
-
Million Dollar Question...
I'm sure this has been asked before, but I did a search to no avail. Which do you recommend? ICND1 >>> ICND2 and break it up or CCNA? I'm really struggling with this... Not sure if most found success by breaking it up or not. I am grateful for your input.
-
Connection from one switch to another switch
I would like to achieve this type of cconnection Modem >>>> Switch 1>>>>5 computers & Switch 2>>>> 2 computers. So wat will be the DNS Servers for both the switch????? and the IP addresses.
-
CCNA Voice Scheduled
Taking 640-461 Friday... *fingers crossed* doesnt look too intimidating
-
ICND2 Passed!! ---from CCENT
wow. As I sit here at my desk Monday noon (took the test this morning), all I can say is wow. Here's a link from my ICND1 pass. http://www.techexams.net/forums/ccna-ccent/75212-icnd1-passed-network-data-sheet.html Here's the materials that I first used Odom book -- read through this first pass, didn't really understand it…
-
IPv6 addresses
So I think I found a mistake in Odom's ICND2 book, but I'm not sure. Table 17-9 on page 604 shows the following: Global Unicast 2000::/3 Unique Local FD00::/8 Link Local FE80::/10 Multicast FF02::/16 Everything looks right to me except the Unique Local which I'm seeing in Lammle's and others as FC00::/7. Am I wrong or…
-
ccna voice simulation/emulation problem (i can't buy a real LAB)
Hi guys , i am new in CCNA voice i don't have enough money tobuy a real LAB so i will have to use simulation/emulation programs the problem now that after studying the overall view and the start theoretical part of the course, i am now facing a problem with the practical (LAB) part i am so confused i do not know how to…
-
OSI layer
At which OSI layer a logical connection between 2 hosts is created ? Kindly explain also . I think it is session because its function is to create and tear sessions.
-
Vlan Configuration question
I have been working with the CCNA exploration practice labs and i have came across an issue that i just need a bit of help with. Basically i have 3 vlans vlan 20, vlan 30 and vlan 40. At first i configured each host in each vlan on a separate subnet with default gateway etc... I then changed one of the port assignments on…
-
Management VLAN
Hi I have a router on a stick setup with three subnets each in different VLAN say VLAN 50, 60 and 70. Im setting up the management interface for the switch and have used vlan 99. What is a suitable ip address for the management vlan. Should I use an ip from one of the three subnet ranges. Thanks
-
ICDN1 Pass (Question about bug)
Hello all~ Been lurking on the forum for a while~ this place gets you excited about going out, taking a test, and getting certifications! =p Anyway, passed my first exam ever in this world yesterday. CCENT (ICND1) 987/1000 How I prepared: - Watched: CBT Nuggets ICND1 videos with Jeremy Ciora (at the same time as below) -…
-
Test Prep
I am interested in purchasing test prep software any preference between Boson or Transenders? For CCNA cert.
-
The $2.3 million home lab of Scott Morris, Quadruple CCIE
Brad Reese on Cisco: The $2.3 million home lab of Scott Morris, Quadruple CCIE
-
show ip of VLANs?
Is there a switch command that show the IP networks of the VLANs in a switch? I would just do a show run and see the ip and netmask for the interface configured of a VLAN member (and reverse engineer it). But there must be another way..
-
Hierarchical addressing network addressing scheme?
I have enough concept about hierarchical addressing network addressing scheme and what i don't understand is this question i read somewhere : Which two benefits are provided by using a hierarchical addressing network addressing scheme? (Choose two) A. reduces routing table entriesB. auto-negotiation of media rates C.…
-
Subnetting Speed
I can finally subnet (well, mostly), I don't think I'm particularly fast though. How fast do you need to be for the CCENT? What were your strategies to do it faster? I find that if I write down 128 64 32 16 8 4 2 1 on a piece of paper it helps me to calculate stuff a bit faster. Is that bad, though? Do I need to be able to…
-
SMB Solutions for Engineers 650-196 Test
Anyone taken this recently? How did you prep for it?
-
Wendell Odom's ICND1 book query.
I didn't understand something i read in ODOM's CCNA book . It was written in the book : "For example, if a network had 30 access layer switches, and the network engineer decided that each access layer switch should be cabled directly to every other access layer switch, the LAN would need 435 cables between switches! " Why…
-
show which interface ACL is applied?
Is there a command that shows a listing of the ACLs and to which interface/s they are applied? Where can I find this info asides from extrapolating for running-config?
-
VTP domain is automatically configured
I have three switches: SW1, SW2, SW3 I set domain on SW2 and activate its trunking interfaces. Now SW1 and SW3 autoconfigure themselves with domain name of SW2. Why?
-
Vlan query
Suppose i have a switch with only layer 2 functionality and not a layer 3 switch .Its port 1 is configured as vlan 1 and its port 2 as vlan 2 . If port1's PC send a packet to Port 2's PC , would a Router have to be involved as both ports are on separate Vlans or not ?
-
The need or 3+ routers for CCNA?
Hi, I am about to start my CCNA and doing some research it is suggested to have 3 routers and 2 switches to create more topoligies for your home lab. Being quite new in this level of networking, I dont know why you would need 3 routers. Could someone explain why you need this amount of routers please and what the functions…
-
point to point and inverse arp?
Why if i have two routers connected to a frame relay, they do not learn about each other? But if I have three routers in a point-to-multipoint network, then they do learn each other dynamically?
-
Discontigous network -- is this not possible?
I have 2 buildings Building A has hosts 192.168.1.1 /24 192.168.1.2 /24 192.168.1.3 /24 Building B has hosts 192.168.1.4 /24 They are connected by three routers on a point to point R1R2----R3 Where R1 is in Building A, and R3 is in Building B All these hosts are in the same subnet!!!! So how does R2 know where to route…
-
Google messing me up on wires, need answer
I've been making my own cables for a little but I've been making straight through only. I recently started making cables for my switches and I know a rollover cable needs to be used. When I look for diagrams for the cable I see two different types of rollover cables. Anyone have a pic of the color scheme or a link to the…
-
Frame-relay and non-cisco routers
On my packet tracer, I configured two cisco routers with frame relay and it works fine. I changed the encapsulation of Router A to ietf (Router B still Cisco). Do a ping test and works!! I read cisco supports this mismatch. But what if Router A was not a cisco router. A non-cisco router configured with IETF. will it still…
-
RIP Trivia Question
1. In this topology, when you shutdown loopback0 on R1, a routing loop is created between R1/R4/R5! R1 sends IP Address: 10.0.0.0, Metric: 3 R4 sends IP Address: 10.0.0.0, Metric: 4 R1 sends IP Address: 10.0.0.0, Metric: 5 R4 sends IP Address: 10.0.0.0, Metric: 6 ... What configuration change(s) would prevent problems like…
-
show vlan assignment on sub-interfaces?
Is there a command that would show the vlan encapsulation of sub-interfaces of a router? I want to see which sub-interfaces I've configured for a particular vlan.
-
Freshly Certified!
Hello All, As you can see I am very new to the site, however over the past couple of months I have been lurking in these forums and using the study materials here and I am happy to say that I just passed ICND2 with 986! I just want to thank this community for existing. This process is hard enough as it is when self…
-
1841 flash card
I'm looking at upgrading the flash cards in my 1841's and wasn't sure if I'd have to buy from an actual Cisco memory seller, or if I could just buy my own 64MB flash card? Does anyone have any input on this?
-
What is vpn tunnel limitation of Cisco 5505
I have two local network which are 10.1.0.0/16, 10.2.0.0/16 and I have two remote site. Can I setup vpn tunnel separately between with two different local network and two remote site. current setup is below. 10.1.0.0/16 ---> remote site1 10.1.0.0/16 ---> remote site2 required setup is below 10.1.0.0/16 ---> remote site1…
-
STP Question
I need a little bit of clarification regarding STP cost to the root port. I have 3 switches and they are all connected. A is connected to B, B is connected to C, and C is connected to A. A has been elected as the root bridge and C is the designated bridge because it has the lowest cost to the root bridge. My question is…
-
Wait for a voucher or no?
I'd like to ask you something about vouchers. I have been studying for the CCNA with CBTs and I studied the Todd Lammle's book, too. I am now reviewing and doing some tests willing to take the first exam at the end of July. I'd love to get one of those 50% vouchers that sometimes people buy on this forum, mainly from…
-
I need to PM someone! help me out
Hey I have a question I dont feel comfortable posting since I'm not sure who I know in real life (co-workers) is on here.... I got an offer and I am trying to figure it out if it's on the up and up.... the fact I have to ask makes me think it's not.. but I'd figure I'd ask my expert homies at TE... I need someone who knows…
-
Splunk for syslog
Hi, anybody here using splunk free in their labs?I've created a cisco index and configured one of the devices to send to the pc running splunk, and I do see it receving data...but it's showing it as maybe raw data?How do I get it to translate it using the default mib info so I can read it?Example - 7/7/129:53:59.000 AM…
-
Cisco netacad
I went through all of the Cisco netacad courses and I was wondering something. Is there a way to view old coursework? I want to view the slides and do all the practice labs and all.