-
Which order is recommended for tackling the CCNP tests?
I just passed the CCNA and am wondering which CCNP test to tackle first?
-
effect of no VTP server switch (all switches in VPT Client)
Hi guys. I have a problem where if an IP device is plugged into a network, it resets network connections. I have VoIP on the lan, so PC connect via IP phones. So the IP phone shows the 'Configuring IP' on the display. The are two switches on the site with 2 vlans, 1 is voice and the other is data. I discovered that both…
-
question for the CCNA/CCNP old timers
When were the CCNA, CCNP, and CCIE first introduced? I know the CCNA existed back in 2000 and I believe the CCIE was released before the CCNA and CCNP existed, but i'm not sure.
-
CiscoWorks configuration comparison?
I'm pretty new to Ciscoworks and our primary Ciscoworks guru just quit, so I've been tasked with learning a few things about it. Can Ciscoworks take a config, compare it to the devices on the network, create a list of which devices didn't match and what didn't match? Thanks.
-
hey guys some ospf for you, if you need any shows let me kno
I set up a ospf network with 3 routers all connected to a switch, also with r-alfa and r-beta connected with a serial cable, here's the config and the errors at the bottom are from r-beta r-alfa configuration config t int s0/0 ip address 10.0.66.1 255.255.255.0 bandwidth 128 clock rate 128000 no shut int e0/0 ip address…
-
CiscoWorks Question
Hi all .... If I have a network and running NMS ( ciscoWorks) for managements purposes. If i add a new device without updating the NMS nor configure SNMP for NMS in the device? Can cisco works tell that there is an unknown network device connected to the network ?
-
static command question
this is on a pix 525 with 7.2 code I'm trying to create a static and allow traffic from outside to an inside host using a static with an IP from the DMZ. So say my outside is 10.0.0.x/24, DMZ 10.0.1.x/24 and inside 192.168.0.x/24 My outside pix interface is 10.0.0.1 DMZ is 10.0.1.1 and I have an inside host on…
-
pptp shutdown after config IPSEC site to site
This is very extrange: I configured simple pptp for many users outside of the company, I did a ACL to permit any to any, it was working fine. Yesterday I confiugred a VPN site to site with IPSec, It is working perfect, but my pptp user can logon to the pix 501 but they can not ping my inside network (they can not do…
-
looking out for a 3550
I'm looking for a L3 switch at the moment what's the difference between SMI and EMI in terms of the cisco exam coverage
-
Root Guard, BPDU Guard, etc
Ok then techies... having a hard time keeping this straight. Hopefully one of you has worked out a simpler method. Portfast I get... ideally suited for ports connecting to one node. Doesn't share in STP. BPDU Guard... again, for end user devices. Question: if run globally on a switch where a port is already connected to a…
-
Ospf neighbour and LSA question????
Ospf neighbour and LSA question??? Does OSPF consider its neighbors to be only those directly connected or the opposite router over a WAN link and not all the routers in the same area? If this is correct does when a change is heard through a LSA does it only inform its neighbors of the change? So if r1 r2 and r3 were…
-
CallManager, IP Phone, Catalyst Switch, Voice-enabled Router
To Mike or other fellow Voice Expert, I want to know how to connect this devices together : CallManager, IP Phone, Catalyst Switch, Voice-enabled Router I don't know which order is correct... Is this enough to practice with that or I have to follow : 1 Compaq CallManager 4.1 server 1 VG200 gateway with 2 FXO and 2 FXS…
-
ISCW tips??
Hi all, I have my iscw booked for next week, anyone know the pass mark? and if there is SIM's in the exam? Thanks
-
IS-IS Adjacency question
In the cisco press CCNP BSCI Office Exam Cert Guide 4th edition, there is a question about IS-IS that says: For an IS-IS adjacency to be formed and maintained, both interfaces must agree on which of the following: a) If Level 1 both must be in the same area b) System ID must be unique c) Both must be configured at the same…
-
Passed BCMSN
Piece of cake,,,,,NOT!!!!!U gotta know your stuff, and expect the unexpected. Bring on the BSCI. Especially, DAI and wireless.
-
BGP question
Hey guys, I've got a quick BGP question. Basically I'm using BGP as a failover solution on Primary and Secondary routers so that if the primary goes down, BGP will kick in and route LAN subnets down the secondary. When I test this (by shutting down the primary) the BGP kicks in and routes down the secondary as intended.…
-
something interesting i noticed about OSPF non-broadcast
while mucking around with my home lab i noticed something that i found to be interesting. I have an OSPF non-broadcast network configured over a frame-relay switch. So as you know in a non-broadcast network you need to specify the neighbors using the nieghbor command. So i have my hub router setup with a few neighbor…
-
Demultiplexing an E1 on gateway
Hello, I am receiving a full E1 (30 channels) into a voice gateway. Currently I have a DSPfarm in this gateway using all the DSPs for transcoding and conferencing, and the E1 is used fully for outgoing and incoming calls into our VoIP network (using callmanager). What I want to do is using about 24 channels for VoIP, and…
-
Does cisco have any technical trainer certs?
Just wondring does cisco have any trainer certifications?
-
CCNP self-study
Just an exploratory question - I finished my CCNA at the local Cisco Networking Academy here in town, and I took this semester off to study for other things. Unfortunately, two of the four CCNP classes I would need are only offered in the Fall. So I'd have to wait an entire year to "pass" the schooling for CCNP, or study…
-
Scheduled wrong test with VUE
Hello all, I have very bad news about my testing experience with VUE. I honestly thought I registered for the right test 642-901 but VUE insisted I registered for 642-961 which I never knew existed. They refused to change it to the right test and allow me to take the correct test. They also refused to reschedule or cancel…
-
New to CCVP, looking for some advice
I'm looking for some advice about getting my CCVP. How releavent is the material in real-world and production envrionments? Are there any pre-requistes such as CCNA. Second, can I pass the exam without setting up a lab. Given that this is a Cisco certification, is the knowledge transferable to other VoIP standards. How…
-
ONT vs CIT
How do you guys feel about the move away from troubleshooting, to putting in voice/qos/wireless stuff in the CCNP? Having done ONT myself, I'm not really sure why they decided to remove troubleshooting. They've taken something that had a lot of practical application and use, and replaced it with a bunch of theory - on…
-
some OSPF questions....
two questions i have on OSPF... Q1) in my lab im mucking round with OSPF, and i noticed that after a show ip ospf nei command that there were two BDRs: routerB#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface 192.168.1.1 0 FULL/ - 00:00:34 192.168.1.1 Serial0 12.3.1.1 1 FULL/BDR 00:00:39 172.16.1.2…
-
Experience
I have experience with VoIP and CCM but not really in depth knowledge. I can set up a GW/GK and do all the route and trunk configs on call manager. I also have working knowledge of PBX. I also have experience setting up CCME on routers. I am thinking of going into CCNP next, but someone suggested with my skills I should go…
-
Question about Dial Peers
Hey guys, I am on my last leg of preparation for CVOICE and rereading the Cisco Press Self-Study guide. I didn't understand this the first I went through and still don't so here goes. What is the difference between 'incoming called-number' and 'destination-pattern' ? Why is 'incoming called-number' recommended for inbound…
-
Call Manager Express + isdn pri
Could anyone assist. Im running Call manager express 3 on a remote router. I have an Isdn pri line using 30 channels for voice. Callers sometimes find isdn lines engaged yet there wont be anyone on the phone. where could my problem be? Othertime I had a similar problem, but instead of isdn pri, I had 2 voice cards with 4…
-
Layer3 Switching Q.
OKay lets say I had a distribution switch that had layer2 links to my layer2 access module. Then it has layer3 IP conections to the core. Then lets say for some reason I have decided to cross the core to get to my DHCP. Must I still use the helper-address command to create a unicast transmission from the distribution…
-
UDLD
Dear Friends How r u all ??? I wish u r in very good health ..... I have 2 questions about UDLD and i wish u could help me : 1)Does UDLD can be enabled on any ethernet interface ?? 2)UDLD gives protection against miswiring .... what is meant by miswiring ???? I wish u could help me Thanks in advance
-
MST vs PVST+ pros and cons
I might need to move away from PVST+ and to MST but before I make this jump I would love to hear from folks who have done this or considered this. I am looking for any major issues with using MST or with moving from PVST to MST. Regards, PW
-
BCMSN... information overload.
I just finished ready Hucaby's BCMSN Cert Guide, and started on the scenerio questions at the back... and I'm shocked at how much I've forgotten in three weeks. Just so many details. The book's CD has a tonne of questions, but I'd love to get hold of some extra study guides / etc... and I noticed nothing here on the site.…
-
Strange recommendation
Okay please bear with me here but my physics at school was rubbish and I am trying to understand wireless, xdsl, cable and the RF spectrum. So can anyone recommend a good book on these topics that really explains things including all the stuff on wave theory?
-
Anybody else besides Kevin Wallace?
Starting studying CVOICE. I have my Self-Study guide by Kevin, the flash cards are by Kevin, and the Knowledge Net CBTs are by Kevin. I was hoping to get information from different sources, which usually means different people! Any suggestions? Also, are there simulation questions on CVOICE? I assumed that it was just a…
-
BCMSN lab, with Nortel switches?
Hey techies, Just finished reading Hucaby's BCMSN book, and thought I'd put myself through a bunch of scenerios. I have 3 2950's to work with, but I also happen to have a dozen Nortel Baystacks that we've replaced in the last year. Now I know that Cisco and Nortel share BPDU's just fine, but I'm wondering if playing with…
-
BSCI practice questions or no
alright fella's, I have been studting the BSCI via self study book and home lab. I have not looked at any practice questions and to be honest if you learned the labs and studoed then really what is the purpose of the practice questions? I am feeling good and getting ready. collecting 2 cents here...
-
Remote configurations makes me on edge so to speak
I am just gonna throw this out there. Anybody get a little on edge when you have to configure a router or switch that's a WAN/remote site? Even though you know what you are doing, you check check and recheck, to the point of something that should take five minutes, ends up taking around 15 from all the dang checking! :) I…
-
Juniper/Cisco
-
interarea? intra-area? O IA? O?
in OSPF if you do a show ip route command and a route is shown which has O IA in front of it does that mean that the route was learned from an OSPF neighbour within the same area or from outside the area? Does this make it an intra area or an inter area? the definition on the actual router says that it is and Inter Area…
-
eigrp path removal from the topology table
These are two statements form the BSCI press book 1) If a network connected to router A is disconnected , Router A updates it's topology table and routing table and sends an update to it's neighbors. 2) When a neighbor receives the update it updates the neighbors table and the topology table. It's Number 2 I ahve the…
-
BSCI 642-901
I feel like the Cisco Press book is not enough to prepare me for BSCI, i'm almost done with it and i was wondering if anybody had more references for the exam, maybe some www.cisco.com links available to help in topic such as "Manipulating Routing Updates" which includes Redistribution and DHCP Configuration, "IP…
-
CCNP certificate status queued for more than 45 days
I have completed the CCNP Certificate requirement on 23-July-2007. i have requested printed form of certificate on 26-July-2007. The cisco certification tracking system is showing the certificate status as queued from 1-Aug-2007. It's now more than 45 days since i completed certification requirement, but still the status…
-
Passed 642-812
Phew passed BCMSN with 945 although there were several points that I thought I had failed it there were loads of realy arbitary wireless questions in there that I though I had got wrong even though my report shows 90% for wireless. Anyhow passed it and it feels good to finally get this one out of the way as I kept putting…
-
SNPA 642-523 Where to find this book?
Acording to Cisco Web site the 642-522 will end next month. I am trying to get 642-523 book but I can not find it anywhere. Do you have any source for that book. I do not believe that I will have time to go for the exam 642-522, so I want to prepare for the 642-523. Thanks. Raul
-
ccvp lab
Ok, so work has agreed to fund a little CCVP lab. So where should I start? Ive got my CCNA and did ok with that, at home using a couple of 2501's and some 2924's. But Im not even sure where to start with a VOIP lab. Work uses Shoretell... but they want me to get the cert so they are willing to get whatever I need... or at…
-
For those who have earned their CCNP....
I'm fairly new to networking & I'm trying to get a feel for what it's really like to work in the field. What is your job title & what types of things do you do on a day-to-day basis? I appreciate any input! :)
-
experience for CCNP
Can anyone tell me how many months experience Cisco recommends before attempting the CCNP? I've looked all over their website & can't find it anywhere. I know some people on these boards believe that you shouldn't get your CCNP without enough experience as it looks bad. Any opinions about that are welcome as well. :)
-
ONT exam first?
Hi guys, Just wondering if anyone has done the ONT exam first. Basically, I was about to start on the BSCI but I need to learn QOS quite urgently for work purposes and so I've decided to maybe go for the ONT exam first. Does it matter if I did the ONT exam first or does it build upon BSCI, BCMSN, ISCW?
-
Architecture Models
OKay So I have been reading the BCMSN book and I have read the first chapter like 4 times because I just can't seem to wrap my brain around all those architecture models. SONA, IIN, AVVID, Enterprise, yatta yatta.....They use the words "functional area" and "Module" so interchangeably. You have a functional area and in…
-
More STP topics
Okay I have gone and confused myself here with the different types of spanning-tree. Firstly there is CST or 802.1Q spanning-tree which runs over the Native VLAN, is this right? Can it run with ISL as it's trunking protocol? Also does it only support STP or does it also support RSTP? Next there is PVST which requires ISL…
-
Questions on IS-IS on BSCI
How many questions did the test takers actually have over IS-IS? Just wondering if I should attempt to memorize the TLVs... thanks
-
STP Questions
Hi all, I have been reading through the BCMSN study guide which I must say I find a much better book than the BCMSN self study guide which seemed all over the place. Anyhow that is beside the point. I want to check that I have this right if you have BPDU filtering enabled on a Portfast interface then you connect another…
-
EIGRP default route propagation
Hi everyone, I have the following scenario: R3 / |R1------R2 | \ | R4 R1 is connected to the outside world and I want to create a default route and advertise it to the other 3 routers through EIGRP. I did this setup on dynagen, so I had to create a loopback interface on R1 and use at as the default route to the outside.…
-
Colleges offer CCNP/CCSP courses in VA, DC
Does any know any colleges offering good trainning programs in CCNP/CCSP around Virginia and DC area? Ideally, the whole program should last around 6-10 months. Many thanks.
-
PIX 506e
I have a cisco pix 506e, currently running 4.3. I have inhereted this pix and there isn't anyone here that knows the password. I'm trying to run their password recovery program on this pix but I'm having some communication problems with it. I am connected via the console cable and I've assigned IP's of 192.168.1.75 gateway…
-
SIMS for 642-812
hey, I got the exam schedule for the BCMSN this week Im just curiuos on what kind of SIMS should I encounter? Thanks for your help
-
New to CCNP please help
Hello guys, I have just completed my CCNA and i am starting to get myself prepared for CCNP. I will be doing the self study most of time. Firstly i m preparing for BSCI exam and from there on i 'll move furthur. I have one question Do i need to have extensive lab exprience for BSCI exams How do i prepare myself on…
-
OSPF RID
By default the highest IP address on a loopback interface is supposed to be the RID even if that loopback interface isn't OSPF enabled. I'm not sure what I'm doing wrong, but I have 3 routers connected via frame-relay circuit with addresses 172.12.123.1 .2 and .3 and I have configured a loopback interface address on each…
-
OSPF RID
-
Question about Voice over IP
If I am able to provide communication between two Ip phones via call manager and a switch, How do I let these phones communicate with the outside world? router with callmanager express>switch> 2Phones
-
OSPF, Areas and Weirdness...
trying to get back into the wonderful world that is OSPF but having some issues at the moment, I configured a network like the image below, all routers in a single area (0) all with the same bandwidth on every link. Some routers are connected via serial xover, others by ethernet xover. So obviously there are multiple paths…
-
Dumpster diving can pay off sometimes
My boss told me that some of the engineers threw out some end of life / malfunctioned equipment so I checked it out and in all there wasn't anything fully functional, except for two 2900xl switches (turds don't even have 4 mb of flash, so I can't install 12.x IOS). Amidst the junk I found three tossed out 7206vxr modular…
-
Suggestion for MPLS BGP Exam
-
NMS Q!!!!
Hi all, I just wondering , If i have a very big network. with more than 300 switches and routers. Sure we will use NMS(Either ciscoWorks or HP OpenView) to ease our lives. Now If we added a new network device, can the NMS detect it directly ? Or do we have to manually add the device in the NMS?
-
Admin the Pix Firewall
I am new with Pix firewalls, I was hire by a company to do destop support three days ago and now I am working with some servers 2003, desktops and a Cisco Firewall Pix 500. I am not sure but I understand that there is a graphical interface to admin the Pix. Is that true? and if is true how to do it? Thnaks. Raul
-
STP Security
Dear Friends I wish u r fine ....... I wish u could help me understanding some topics in STP Security .... 1)I read this statement is Cisco Material "Loop guard is incompatible with root guard. Also, loop guard should not be enabled on PortFast ports" ..... Why ??? 2)Does unidirectional links caused by cable problems (utp…
-
hi guys, I am new to CCNP and I need some advice.
hi guys. I am going to start my CCNP soon. Here are my questions. 1. I am working in a VOIP company, so I got 2 CISCO 1760 and 1 2500 routers. The problems is I don't have any cisco switch at all. So how many more cisco equipment need to get in order to start my own lab ?? 2. Now I am going to pick one of the topcis to…
-
SNPA 642-523 Hardware Requirements
Hi all, I'm looking at studying for my Cisco Firewall Specialist cert (with intentions of going CCSP at a much later date) I was wondering what is the minimum I can get by with purchasing. Id rather buy real hardware than run emu's or rent rack space. I have no Cisco security devices. I only have my CCNA equipment (2950,…
-
Easier book for Multilayer Switching?
I have Cisco's textbook "CCNP 3: Multilayer Switching," and it's as dry as a sun-scorched bone. Is there another book out there that is easier to read which covers the same material? Possibly something by Todd Lammlie?
-
Weird problem configuring a router with a DSL Modem
Here is a diagram of the described network. I have a Zyxel 623 DSL modem plugged into Fa0/1 on the 7206. Fa0/1 is configured to obtain its IP via DHCP. Fa0/0 on the 7206 is connected via ethernet to the uplink port on the 1900. Plugged into the switch is a Cisco 1700 router and a laptop PC. The 7206 is configured to be a…
-
Greetings from the CCNA Forum - Help Needed
Hi Guys, I'm actually going for my CCNA but i need to call upon your expertise with a problem that im having that goes beyond a CCNA. We have a 1821 router that we use as a backup router incase our primary goes down. Hanging off of this router is a DSL connection. We connect the 1821 to a Cable modem which we then get…
-
ccsp exams hardest to easiest
Hey Can you kind folks break down the hardest to easiest for me: I really appriciate everyones response.
-
IOS for BGP?
anyone know what version of 12.4 IOS supports BGP?
-
IPCC and Historical Reports
Hi fellows, I have been making some test calls with an IPCC server to see how cisco historical reports show the call data. Unfortunately, the reports show only the calls I made yesterday, not the calls I am currently doing. Is there a setting where I can intruct the historical database to report me the calls that I am…
-
QOS question for VOIP (ONT) help required
Hi can someone explains the answer to me for the below question Need to implement the proper IOS tools to ensure that VOIP works over the network. Which queuing and compression mechanisms are needed to effectively use the available bandwidth. A. Priority Queing (PQ) or Custom Queuing B. Real-Time Transport Protocol (RTP)…
-
What are these cables called?
what cable connects to the analog phone? and what port does it connect to on the router? what would a sample configuration on the switch and the router be for both phones to communicate. Thanks
-
EIGRP Question
This is hopefully an easy question, but I'm asking as I want to get the terminology right. Ok, you're running EIGRP and you have a Router that goes offline. The Router that was previous connected to the Router that went off line now needs to find a new path to the remote network. The router does not have any feasible…
-
Question on Defaults and protocol/system design
Hey guys, I am studying CVOICE and BCMSN right now and just watching the queing video from the Train Signal BCMSN and just remembered a question I have been meaning to ask. And it is this. I am not just talking about queing specifically. But, what I want ask about is default values. For example, the default packets for…
-
prevalence of knowing CatOS?
I just bought a Catalyst 5505 for layer 3 switching and the thing runs CatOS. The RSM module I also bought runs IOS however, so I'm good in that regard. I'm curious to know though, how worthwhile it is to learn CatOS. Are there many routers still in the field that run CatOS? According to various sources CatOS is still used…
-
Should I try to beat the dealine and take 642-425 IPTT?
Hey everyone - I need to decide soon if I should try to take 642-425 IPTT before the 10/2/07 deadline or if I should wait and take 642-426 TUC when I feel I'll be ready (probably in December). I've already passed CVOICE and I'm scheduled to take CIPT in 2 weeks (actually retake!). I had originally planned on studying and…
-
CBTs
Has anyone here ever compared CBT nuggets with train signal CBTs ? Which one do you all think is better? I see there there is a difference in price but I wanted to hear your opnions b4 I decide. Thanks!
-
POE
Ok I am having a problem with a 3750. We had a power outage and the switch rebooted. Since the reboot I can not get the PoE to work. The show controllers PoE command delivers no output. Any ideas?? I've tried google and Cisco.com with not much luck. We have the phones plugged into external power for now, but I'd like to…
-
Finally getting lab equipment
Been back at work for about a month now. Turns out the lab equipment has been there for about 5 months. We just opened the boxes last week. Starting with a couple of CallManager Express routers. 2801 and 2821 with Unity express AIM for the small one and Unity express NM for the 2821. It's about time. Wish I had the stuff…
-
SSL Tunnel through an IPSEC Tunnel?
We have a situation where there is an additional secure area of our network within our corporate network. Within our network the secure zone is protected by a PIX. This PIX is managed by a separate security team than the VPN concentrator. We have a need for direct port access to devices on the other side of the PIX. We…
-
CCNP Home Lab ---- I'm Sorry Please Read!!!
Ok, i'm tired of searching through all of the pages of suggestions. And yes, i hate starting new topics that have already been posted ( as well as opening a sentence with the word 'And' ). Please someone give me a list of what equipment to buy for the CCNP for all 4 tests, i'm getting real discouraged real fast! Just a…
-
CCSP Boot Camp....
So as most of you may remember me I got my CCNA earlier this year (Janurary) I took a pretty intense break, though not intentional it was prolonged due to other life obligations. I am planning on going to Grad School to focus in Networking/Network Technologies. I already spoke to my advisor a little about this. Without…
-
Chris Bryant CCNP BSCI Package
I am thinking of ordering this and before I spend 100 on it I wanted to know if anyone knows the difference b/w this and TrainSignals BSCI package. Chris Bryants website links me to the TrainSignals site for the contents of his package but when I get to the purchase screen it comes up as 97.00 where as the TrainSignal…
-
Vlan Hopping Double-Tagged
Dear Friends I wish u r all in very good health ...... I wish u could help me to understand a topic in switch security .... In vlan Hopping Double-Tagged attack , can u please explain why this method only works if the trunk has the same native vlan as the attacker ???? I seached tooo much in the internet, but i couldn't…
-
Horror story
Today was a bad day, I want to share my experience with you guys. Tonight I tried to replace a 6503 with another 6503, same model. I thought it was going to be an easy task, "what could ever be wrong?" I thought to myself, I set up a TFTP server on my laptop, copied the original configuration on the tftp server, and my…
-
Cheapest Cisco layer 3 switches?
I need to buy some switches for the BCMSN but I'd like to be relatively cheap in doing so. 3550's seem to be where it's at, but they're still relatively expensive. Anyone?
-
Problem with Pearson VUE?
Hi everyone, I have not been on for a while, as I have been studying my brains out. I scheduled to take my exam next month, and I looked again at my confirmation email for inspiration, when something really odd caught my eye: Appointment Length (minutes): 110 Accommodations: Time extension for non-native English speaker…
-
CallManager version?
Hey guys - I'm planning on starting my CCVP studies later this spring/summer and I'm really looking forward to it. I'm starting to gather up the equipment I'll need for a small home Voice lab (can do some studies with equipment at work). I've searched Cisco's site and here, and I can't find if the test is based off of…
-
getting IOS version 12.4 for 3600 router
hey i'm looking out for a 2620XM and 3600 router both with 12.4 IOS on, keep finding the routers on ebay but they have the older OS on them. How could I get hold of the 12.4 IOS without having to wait to find a router with it already on?
-
How should i wire up my home lab
I now have four routers at home and am going to get stuck into so good old study this weekend.. im just wondering what would be the best way to wire them up... im currently studying for the BSCI, and am focusing on EIGRP at the moment.. so im thinking something like the following what do you guys think? this would be a…
-
Flapping HSRP
Hi guys, I know this is not a troubleshooting forum, but just thought I may share my problem with you and see what you think. I have been having problems with a cat 6503 that is one of the core/distribution switches in the network. It is a basic switch block, two core/distribution switches connected to each other, with…
-
ACS, where do I get it
i'm currently planning to start the CCSP, was wondering where people get the cisco ACS software from? wha also wondering is it only supported by windows server operating systems, thanks to anyone who can help
-
problem with ccm installation
hi all i have just installed CCM 4.0(2) on a generic PC. everthing seems to work fine but while trying to open the user options web page, http://<ip-add>/ccmuser i am getting the follwing error You are not authorized to view this page You do not have permission to view this directory or page using the credentials you…
-
Cisco 5400XM IP IP GW configuration consulting
to all, working in a company which is VoIP LD service provider. Had being used TDM PRI connection as local access inbound connection. topo like this: switch carrier -> PRI -> Cisco AS5400 -> Softswitch -> LD termination we would like to embrace the IP based inbound traffic into our system, and still need Cisco GW for…
-
Analog to IP Phone calls
have anyone done this? making calls between an analog phone and an IP phone? PSTN \ AnalogPhone----FXSPort-H323GwA--Network--H323GwB--CallManager \ IP Phone I already set the dial peers on both gateways, setting the dial-peers is actually straightforward, but I dont know whether something is needed to be done inside call…
-
2900 v 2950 Switch
I have a c2912 with IOS : c2900xl-c3h2s-mz.120.5.WC17 It is running Enterprise Edition Software Cluster command switch capable Cluster member switch capable Is it good enough for CCNP study? How does it compare to a 2950, and what exactly is better about the 2950 (not been near one yet)
-
EIGRP Metric confusion
I'm trying to get my head around the metric calculation for EIGRP. So the way i see it is as follows: Default equation is: M = [K1 * bandwidth + (K2 * bandwidth) / (256 - load) + K3 * delay] * [K5 / (reliability + K4)] ok now if we are using the default K values which are k1, k3 = 1 and k2, k4, k5 = 0 then the equation…