-
VLAN Trunks
Are amazing. I just read the section about them and I find them to be so cool
-
Becoming irate at Pearson software
I'm trying to install Cisco CCNA routing and switching 200-120 network simulator from Pearson and it stops in the middle of the installation process stating that I already have this version installed. I look everywhere, and no, I don't, it's nowhere to be found, and Pearson's helpdesk people are clueless too and don't know…
-
Extended ACL question ?
Extended ACL for the exam , should I know all the options ? I am focusing on TCP, IP and ICMP.What about OSPF ? Router(config)#access-list 101 deny ? ahp Authentication Header Protocol eigrp Cisco's EIGRP routing protocol esp Encapsulation Security Payload gre Cisco's GRE tunneling icmp Internet Control Message Protocol ip…
-
Passed CCNA:S
Passed the CCNAS today, after failing it once at "Cisco - Live!" Definitely not my favorite cert. I felt like it was less fair than other Cisco Exams. Good parts:* Simulation questions. Should include more of these. Really measures what you know better then some of the others * Questions about IPS, IDS, * Questions about…
-
Routing trouble
Hello I have encountered a problem in reaching a host. It is shown in the picture below. I could ping the 10.10.10.1 ( which is routers interface from all other computers. But i couldn't reach the computer in the same network with address 10.10.10.2. There is route defined. Any suggestions will be really helpful.
-
it's switches like these that make me pull out my hair!
This is a brand-new, 15 minute old 2950 switch and I go to connect the 3750G to a 2950, setup the SVI and assign the ip address to vlan 100 and connect it up to the 3750G and I get a native vlan mismatch. For the lab I've been using the vlan 1 as the native vlan and didn't change it across the board, but for some odd…
-
VIRL vs GNS3?
So I just recently read about this new simulation program released from Cisco. For those who have tried it, how does it compare feature wise to GNS3? So far, it seems VIRL can't go more than 15 devices (GNS3 can, given the hardware support) and it cannot simulate L2 Switches (which is not a big deal). Opinions?
-
Subnetting Class A and B addresses
Is there anyone who can explain subnetting a class a or b address or send me in the right direction? I am studying the CCNA R & S book and don't get the examples for class A and B but understand class C. Thanks, -Benny
-
ICND1 100-101 Pull the Trigger or Not?
Hello Everyone, I've been a long time lurker here, looking to get any advice as i have a day off of work coming up (July 3rd) and wondering if i should attempt going for my CCENT. I have some real world experience working with Cisco equipment as-well as my own LAB which consists of a 1841, two 2811's and two 3550's. I have…
-
CCENT failure (2nd attempt)
Today I retook my CCENT exam. I previously attempted this about 5 weeks ago, and came away with a score of just over 600 (Having never attempted a Cisco exam I went in prepared, did well on the subnetting questions but was ambushed by a simulation). 5 weeks later I had another crack at it, and did a LOT better. While I…
-
Book For Sale - FGL Switch 300-115 - Brand new
I'm not sure if selling is allowed here, if not, please delete. I have a brand new copy of the Implementing Cisco IP Switched Networks (SWITCH) Foundation Learning Guide: (CCNP SWITCH 300-115) that I would like to sell. It's brand new and never been opened, meaning I've never opened the cover or flip a page. Implementing…
-
Network Design | IP telephony Design
We were asked to create an ip telephony topology earlier for 25 users that is scalable to 100 users. We were also asked to proposed what routers and switches to use. I'm not good w/ this. This is my first networking job so i'm not sure if i'm doing it right. Btw, this is for small business client. As you can see, do i…
-
ICND1 Passed !
Passed CCENT, scored 960 :D I would like to thank this community for answering several of my questions and for clearing some last-minute doubts. Now a couple of day of well-deserved relax.
-
CCNA 200-120 passed!
Hey guys, I haven't posted much except for a post here and there for some time but the place I'm with now sent me to a Global Knowledge course which in turn got me a 2 shots at the cert. Studied using Lammle, Bryant's Udemy and CBT nuggets and came away with a 890. I'll take it... was a long time in the making. Glad I got…
-
Packet Tracer for CCNA Wireless?
Was hoping to not have to buy any hardware for this exam. Do any of the emulators have what the CCNA Wireless needs? Casually looking I did not see any controllers in packet tracer...
-
Is there a command that states the size of the memory sticks in a cisco router
I know show version will tell you what the total amount of memory is. But, how can you find out if there are 2 256mb sticks vs just 1 512mb stick
-
After configuring tacacs cannot access to cli
After configuring Tacacs+ cannot access throught tacacs or telnet: ! aaa new-model ! ! aaa group server tacacs+ TACACS+CG server [server ip address] server [server ip address] ! aaa authentication login default group TACACS+CG enable aaa authentication enable default group TACACS+CG enable aaa authorization exec default…
-
CCENT Passed!
I finally passed the ICND1 exam with a 867, now onto the ICND2. :)
-
what is subnetmasl of my public ip..?
Dear Users, some days ago i bought an ip address for wan connectivity, as we read in networking that every ip address has a subnet mask but i dont know how to see my subnetmask. and one more thing is this that can i make the subnets from my ip address ...? Thanks
-
WGU material?
Anyone taken CCNA & CCNA:S through WGU lately and know what material they use? I believe I read you get CBTNuggets but not sure if that's still the case. Any info is appreciated.
-
When passing this test
Do you get a certificate for passing this test like when one passes the CCNA?
-
Confused here by this question
This is from Odom's book, DO I ALREADY KNOW THIS. The book has it as answers A and B
-
A bit of motivation - CCIE at age 19
Hey everyone, I don't normally post stuff like this, but this story came across my LinkedIn feed, and it just seemed like something I had to share. This is a press release from the Cisco Learning Network about a 19 year old who progressed through the Cisco certification track and earned his CCIE at an amazing age of 19. If…
-
Any idea where I can get a discount to take my ICDN1/CCENT exam?
Hello again everyone! I'm on the verge of finishing my reading of my ICDN1 book and am beginning my search to finding out where I can get a solid discount to take my ICDN1/CCENT exam. If anyone knows of anything, please let me know! Thank you!
-
Bandwidth is showing 128kbit Instead of 1544kbps
I have made a network using EIGRP and then i run command show interface serial1/0 instead of showing default value i.e 1544kbps it is showing 128kbit. Have I done anything wrong?
-
NAt Failed: but why? - I found the issue but might be helpful for someone...
Ok, So I ran into a problem today with my NAT lab I made at lunch and I configured it in like 20 minutes and then it didn't work and I was like WTF!!! ...I had it all planned in my head and then I got it all done and I was like why is it not working.... can anyone see what I did wrong? took me forever to look at the config…
-
Can't ping pc on other host
So i have made this topology and tried both RIP and EIGRP but unfortunately both are not working
-
Cisco Path for Cyber Security Track
Hey guys (and gals). My cert plans may have changed slightly. After talking again to a counselor at WGU, I learned they pick up the tab on both CEH and CHFI, as well as give you 2 vouchers each in case you fail. That being said, studying CEH on my own right now might not be the best use of my time. My job right now is…
-
udp checksum ,and tcp windows
hi i want to know 3 simple thing 1- on UDP , i heard that udp not always check the checksum , is it correct? why ? andif can i get Official source that say it 2) on TCP PDU there a windows value, i not get if that say how many segment we can send befor we get ack , or if it number of bytes we can send before we get ack and…
-
OSPF wildcard mask
Found this in Odom's book "The answer with wildcard mask 0.255.255.0 is illegal, because it represents more than one string of binary 0s separated by binary 1s." It means that I can't mix 0 and 1 in a wildcard mask? All 0 must be on the left side and all 1 on the right side or viceversa with no mixed 1 & 0?
-
Subnet Range help
I've been following the subnet guide found at Subnetting Made Easy And Other Cisco Tidbits: Subnetting Made Easy - Critically Acclaimed! and I'm finding it very hard to understand solving the network ranges. What I mean is for this example, I don't get how the solution for the valid range is 172.16.0.1 to 172.16.127.254.…
-
I can't ping another host PC on the same switch and subnet.
This has been driving me bonkers. In theory this should work since I put both PCs on the same subnet connected to the same switch. I am using a network simulator and I don't know what went wrong. I just started out with a fresh switch and two PCs connected by a straight through cable and they can't ping each other. They…
-
Ccent 4/29/15
So I've been busy the past few months since passing the VCP5-DCV exam. With getting a new job and taking ownership of my own VMware cluster with Equalogic SAN and Dell N2048/3048 switches (that have very similar CLi's to Cisco thanks for Force10) I've been pretty much using the CCENT labbing experience to it's full extent…
-
Best places to download free gns3 topologies and labs?
question is in the title, the cbt nuggets icnd2 intro says they're out there anyone know where i can find a couple good ones, im in a labbing mood? thanks
-
Just got done with the CCNA 200-120 and bombed it
I bombed it. 725 with the passing score of 825. Operation of IP Data Networks 33% LAN Switching Technologies 70% IP Addressing IPv4 and IPv6 67% IP Routing Technologies 70% IP Services 60% Network Device Security 20% Troubleshooting 80% WAN Technologies 40% I can make excuses like I only had 2 hours of sleep last night…
-
Cisco 2106 WLC
I figured I would post this here since the CCNA forum gets the most views. I purchased a Cisco 2106 Controller from the Bay for cheap and it looks like it has a corrupt flash. Its having issues mounting the partition. I opened the case and verified the compact flash is seated but no luck. I tried a new CF card that I had…
-
Question for employers of network administrators regarding CCNA exam pass
Hello, I was talking to a friend of mine who has been working as a network engineer for a year now after getting his CCNA, and he told me that employers look at the way you passed your exam. He said if you split the ICDN1 and 2 and pass it that way that its looked down upon in comparison to passing it all in 1 go. I'm very…
-
CCNA Netacad query
Hi guys and girls, I completed my Netacad CCNA semester 1 final exam and passed that part of the course last night, hoping to hit my CCENT later this year after nailing semester 2. Have many of you here done the NetAcad course and the CCNA external exams, if so did you find the course prepared you adequately or did you…
-
CCENT > Network + ?
Hey everyone, I just passed my CCENT exam this morning and am planning to continue on and take my CCNA Security in the near future. But the question I have is this, I have heard that the CCENT is harder than Network + and that the only difficult thing about Network + is the antiquated technologies they test for. So I'm…
-
Expectations of freshly minted CCNA's
I plan on sitting for the 200-120 this coming Thursday (6-25) and am curious about the expectations for freshly minted CCNA's in the real world? I have been working in IT for a long time but none of my roles ever really had a focus on the network side of things specifically. I guess what I am getting at is there is so much…
-
ICND2 - Crushed it!
I've had my CCENT for almost three years and have been putting off getting my CCNA for about that long. Three months ago I decided to try and make it official, so I hunkered down and starting preparing for the exam. I took it on Friday and scored a 986. The security camera in the room caught me doing a couple of fist pumps…
-
minicom
Hi guys, I want use minicom to connect on my equipment (switch and router) I install minicom on ubuntu and configured it with a usb to serial adapter (/dev/ttyUSB0/) However I am not able to see my device. When I run minicom I see only Welcome to minicom 2.7 OPTIONS: I18n Compiled on Jan 1 2014, 17:13:19. Port…
-
CCDA material in ARCH
Hey guys, I've been asked to do a lot of design projects at work recently. I am thinking of picking up the CCDP to polish my design skills. Is ARCH book sufficient for CCDP studies or is there any material that is not covered in ARCH that I will need in the CCDA book? Thank you
-
PASS!!! 100-101 ccent exam
Hi All! I justed passed my ccent exam. Anyways Good luck to you future test takers! On to the next exam in a month or 2.
-
Connecting Home Lab to home network
Hi Everyone. I'll be starting my CCNA journey in the next week or so and had a question. So I have made the purchases on ebay to make up my home lab and currently being shipped to me (yay). My home lab consists of... 1x AS2509-RJ 3x 2811 Routers 3x 3560-TS Switch 1x PDU I've read a lot that a person shouldn't connect their…
-
I Passed ICND2
The test was hard, my score was 960 and I'm very happy. I was well prepared with EIGRP, Frame Relay and OSPF. My study resources were: Chris Bryant's videos, the books by Lammle and Odom, the 31 Days Before books and various internet sources. I also spent a lot of time with my lab and GNS3. Up next for me is CCNA Security.
-
CCDP Helpful Preparation Tips
I'm fresh off completing CCDP. (01/19/2015). I have here a list of tips and links (mostly links) that might help you in preparation for the CCDP. With regards to the syllabus for the course, it breaks down like this: 30% - Campus 24% - IP Addressing and Routing 08% - WAN 32% - Data Center 06% - Security Based on my…
-
Frame-Relay problem
Hi Guys, I'm new to this forum, and I'm on getting CCNA 200-120 Cert. So, I know Frame-rely is obsolete but Cisco still want us to study on this technology. I'm working on Frame-relay from this website http://www.freeccnaworkbook.com/workbooks/ccna. However, I can't ping other routers nor I can't ping local IP, from…
-
What is the purpose of segregating layer 2 and layer 3 traffic in a distribution swi
tch? Scenario 1: Int fa0/1 switchport mode access switchport access vlan 2 ! Default Gateway int vlan 2 ip address 10.10.10.1 255.255.255.0 Scenario 2: Int fa0/1 no switchport ip address 10.10.10.1 255.255.255.0 In both scenarios, the host 10.10.10.2 can ping the default gateway of the switch at 10.10.10.1. However, what…
-
Need help building home lab for CCNA cert
I am sort of new . I had an account here but can't remember if I ever posted anything. Hi everyone. I have been a Help Desk Analyst for 3 weeks. I want to pursue becoming a Network Administrator and eventually become an Information Security Analyst. I have no certs and a bachelor's in computer science. I have been looking…
-
another lab question
Would this lab work for a ccna wireless? Cisco Ccent CCNA Wireless Lab Kit 640 722 Iuwne Unified Wireless Networking | eBay
-
Question regarding subnets (Studying for CCNA)
Hi everyone, I've ran into a problem while studying for my CCNA exam, and hoping someone kind enough to shed some light on it. The problem asks to find the subnet ID with only the IP address residing in it and its associated mask. IP 10.220.100.18 Mask: 255.255.128.0 The book (Official Cert Guide Cisco CCENT/CCNA ICND1…
-
Inter-Vlan Routing and Internet connection
Let's say I have a network with an ADSL line. My PCs are connected to L3 switches with different VLAN assigned, to route between them I configure their NIC with a default gateway that is the IP of the SVI interface with the same VLAN ID. How can I let the PCs access the internet? I' d like to find a solution in the two…
-
ICND1 Exam Blueprint NAT topics
I' m reviewing the blueprint, I can't find info about these two NAT topics in the Odom/Lammle books: * Source addressing * One way NAT Can anyone cast some light on them? Thanks.
-
Wendell Odom
You drive me BONKERS with the way you put the word LAN in from of every instance of SWITCH and HUB. SHEESH
-
Help setting up Cisco Lab
Hello everyone, I just recently purchased Cisco equipment to set up a small CCNA / CCNP / CCNA Security lab. I have 2 1841 routers, a 3560 Switch, and a 2960 Switch. I plan on tackling the CCNA Security exam after the CCNA exam. My question is how would I separate my lab network from my home network. My home network…
-
CCNA/CCNP Home Lab
Hello, I will be taking and passing my Network+ soon, and immediately starting on the CCNA, and in the future CCNP. I have spent many hours researching my home lab so I do not have to upgrade in the future, and have decided to get 3 routers (probably 2811's) and 3 switches. I spent so much of my time comparing and…
-
Starting CCENT/CCNA and need some advice!
Hello all, I just passed my Security+ exam on last Thursday and am starting my CCENT/CCNA journey and need some advice. I am trying to figure out what the best simulator to use for labbing since I am not in the netacad classes and don't have packet tracer? I did just buy some routers and switches from ebay, three 1841…
-
VTP Question
For a ring topology with L3 switches, can I designate one particular site as a VTP server and the others as VTP clients? Will there be a broadcast storm?
-
Achievement Unlocked: ICND 1
Hey all, I haven't posted on here before (I mostly posted on the Jobs/Degrees forum), but I just wanted to share that I passed ICND1 today. My score was 854/1000. I'm disappointed in the score, but I took the exam on a whim after 2 weeks on vacation with nary a cisco book opened. My resources were CBT nuggets and Todd…
-
Online Course vs. Self Study Question
As a soon-to-be college graduate (One more year to go!!!), I wanted to start acquiring certifications soon so I can go out into the workforce with both a degree and certifications under my belt. I figured to make the CCNA the first certification to acquire. I need your help in deciding whether I should go the self study…
-
ICND1 doable in 30 days?
Is it doable? I know a LOT of the terminology and theories, I just need to get the subnetting down as well as all the configurations and command syntax. Also learn the IPv6
-
Looking for a little direction
Just looking for a little guidance on future career plans. I am a veteran and while in the service I worked primarily with radios. I was cross trained on our LAN and also satellite systems. After leaving the service I wandered through various jobs over the years, none in the tech sector since I didn't really have the…
-
Network Simulator Lite Sufficient?
My ICND1 100-101 book came with the Network Simulator Lite software. For those that have used it, did you find it sufficient for hands-on preparation for the ICND1 exam? The standard version is rather expensive (although still cheaper than buyer Cisco gear on eBay).
-
How do you find the number of host in each range problem
Can someone show me how to find the total number of valid host for the subnet range. 16.125.212.0 /22 I was able to figure out, Network address: 16.125.212.0 Sub mask: 255.255.252.0 Subnets: 64 1st Range of valid hosts: 16.125.212.1 to 16.125.213.254 1022 <-- is this the total number of valid host for this range?
-
CCNA Collab - Anyone find materials for the Video portion yet? (CIVND I think?)
Wondering if materials are out there for the video portion of the CCNA Voice to also obtain the collab cert.
-
Failed ICND2, now what?
Just got back from taking the 200-101 exam and failed with a 775. Needless to say, I'm a little frustrated. I feel like I know the material back to front, but I got bogged down with sims and topology questions. I had 16 questions left with 10 mins to go, and was still getting topology questions. I had to make a rough guess…
-
Purpose of a /32 host mask?
I haven't come across /32 addresses (apart from loopbacks) and I was wondering what the point of them is. If they're /32 addresses then surely every bit will be a network bit, and therefore how could you assign this to a host?
-
Ticketing system
I was wondering what ticketing systems do internet service providers use? I.e. Rogers, fido etc? Do they use servicenow, or zendesk or something else? I just wanted to use the demo and practice. Thanks
-
Static NAT , OSPF Null route redistribution , Expiry problem
My configuration : Router 0 : router ospf 10 log-adjacency-changes redistribute static subnets network 192.168.10.0 0.0.0.255 area 0 network 172.168.0.0 0.0.255.255 area 0 ! ip nat inside source static 192.168.10.2 193.10.8.2 ip classless ip route 193.10.8.0 255.255.255.0 Null0 Router 1 : router ospf 11…
-
HSRP - Maximum number of groups?
Per the title, what is the correct answer for exam purposes? I'm study up for 200-101 and I'm getting conflicting answers. The OCG says 16. Some practice tests say 255. Some online references say 16, some say 255. I tested this on my lab router and I can add more than 16. Some other answers say you can have 16 groups on 16…
-
CCNA:DC - 640-911 Feedback
Hi All, Don't normally post a thread regarding passing 1 exam for a cert but thought this was worth posting for future candidates for the CCNA:DC. Sat the 640-911 today (for the second time today) and passed with an 850 - one thing I would recommend when sitting this exam is going "above and beyond the course books". The…
-
How Can I ping a loopback interface without adding it into ospf
Suppose my routers are running OSPF. I cannot ping 5.5.5.5 unless I use the command below: router ospf 1 net 5.5.5.5 0.0.0.0 area 0 Is there any way to do it without using tis command?
-
Certification renewal question
Hey all, this is probably a stupid question but I'm curious. I currently have my CCENT and it expires later this year. If I were to retake the exam now and fail it, will it invalidate what I currently have, or will that remain active through its current expiration date. Thanks!
-
Ccna related question
Hi there, I've been using the CBT Nuggets series to study for my CCNA and have encountered this question. What do you think the answer should be?
-
Hello and Thank you
Hello All, Thank you for the knowledge and information within these threads. As I increase my knowledge and understanding of networking, hopefully I can help others as well. As with most of you, I'm currently studying for CCENT, with a goal of a career in networking as a Network Engineer. Anyways, just wanted to say thanks…
-
How do you differentiate public and private IP addresses?
I am spending my summer studying for the CCNA exams and one of the things that has me stumped is private and public IP addresses. Here is a question as an example... Which two of the following are private IP addresses? A.) 12.0.0.1 B.) 168.172.19.39 C.) 172.20.14.36 D.) 172.33.194.30 E.) 192.168.24.43 I understand network…
-
Router on a stick issue
I've attached a drawing of my current lab environment. I am having issues and want to make sure my networking is in order before I ask the linux people if I've screwed up. I'm having issues accessing http://192.168.2.2 from the desktop in the drawing when I create a router on a stick setup as shown. Switch:vlan 2vlan 3int…
-
CCENT -> CCNA Security
I'm planning on doing the CCENT followed by the CCNA Security exam (since my primary interest is security). My goal is to transition back into IT (I've been teaching the last few years, non-IT related), and from what I've read, CCNA is a good cert to have, as is the knowledge that comes with it. So what I'm wondering is if…
-
CCNA: DC Completed
Today I passed 640-916. Quite easy exam if you know the stuff (Nexus, MDS, FC/FCoE). Only one wrong answer :)
-
CCNA Hardware
I just passed the CISSP and now want to tackle my weakest domain, networking. I purchased the Chris Bryant videos's for CCNA and Security, however just wanted to get some insight as to what everyone uses or recommends from a hardware perspective to setup a lab. I have heard of a couple of different software simulation…
-
Site Connection via the Internet
Suppose I have two sites, one in NY (10.9.9.0 /24) and one in California (10.18.77.0 /24), and I want to connect those sites through the Internet. I want to ping from one host in NY to another in CA. For example, ping from 10.9.9.73 to 10.18.77.99. What I am trying to say is that although those hosts are connected through…
-
Passed CCNA!
Finally earned my CCNA R/S! I originally failed my CCENT but passed on the 2nd attempt. This time, I managed to pass on my first try. Feels great to finally have it but now I have to work on Project + because I'm in WGU, which I'm dreading. Study materials: CBT Nuggets Lammle Book CCNA in 60 days Packet Tracer Random…
-
OSPF DR election confusion.
I have connected 3 routers to the same ethernet network and to my surprise this is the situation: 1.1.1.1 DR 2.2.2.2 BDR 3.3.3.3 DROTHER I have not changed the priority, so shouldn't the election be based on the router ID? If i turn on 3.3.3.3 after the first two, is the election process done again or it will simply accept…
-
CCNA Passed!
I have put a lot of hours in studying between my last attempt of ICND2 and now. I had originally planned to put a whole month before my retake but I ended up having an unexpected day off and decided to go for my exam again. All the studying between the attempts really paid off. There is nothing like that feeling of seeing…
-
Passed: CCNA 200-120
Hi All This is my first post and have been a long time lurker. On Friday I finally passed the CCNA exam , it was my first attempt but I have been doing the studying for a while. I did the Network Academy for a while a few years back but this was on the older syllabus. I had just put off taking the exam and never thought I…
-
Subnetting.. how to solve "what subnet mask to use get xxxx subnets" question
Can someone please show me a effective way to resolve these type of subnetting problems, thank you. What subnet mask would you use for the 172.18.0.0 network, such that you can get 600 subnets and 40 hosts per subnet?
-
Alternative SSH client?
I currently use PuTTY and feel like it is lacking in features. Anyone else have a good recommend alternative? Thanks
-
Tier
Hi, I didn't get the word tier in this contect clearly until I came across video where I saw the following: Did I get it right? There're 3 tiers, the 1-st tier works directly with clients (which is above in the pic), the 2-nd is networking guys, and 3-rd is data center guys. I'd highly appreciate any clarification.
-
Let's Try This Again - CCNA Help
How 2 Pass Any reviews on this? A few people in the Boot Camp I went last week recommended it. But before shelling out the cash, I wanted to get a second opinion. Anyone use this recentlY?
-
Best place to get packet tracer labs to aid in CCNA Composite Exam?
Hi There, I was wondering if anyone knew of a site that offers downloads to packet tracer scenarios that will aid in my hands-on experience towards taking my CCNA exam. I got a few like: freeciscolab.com, packettracerlab.com, and freeccnalab.com - but they all basically have the same ones and none of them are organized by…
-
Why is it called a 'default' gateway?
If a host wants to send a packet to a host on a different network, it is sent to the default gateway. I would think that because it is called a default gateway, it is implied that there should be a choice of several, which is clearly not the case. Or could this situation ever be possible?
-
Passed ICND2 this morning
That was tough. Like, way waaayyy more difficult than the ICND1. The topologies were more difficult, the questions asked about more of the small details, and you get less time to top it off! Another guy on the forum said "know your spanning tree and frame relay" and I can definitely confirm this. The spanning tree…
-
Do you think I made a mistake jumping right into studying for CCENT?
Hello! You know I have been studying CCENT for a while. Been going slow though, I am just learning the console commands. I have never had networking experience before I studied for this. I heard that a beginner should really get his Network+ before taking on Cisco. I also heard that Cisco kinds of expects you to know these…
-
CCENT..How long did you study for it?
I've been flirting with the idea of getting my CCENT......I manage the switches at my job and touch the routers every so often....I have my net+.......I've yet to pick up and book or even really dive into CCENT....but just to get an idea of what I'm up against, how long did it take some of you guys to get your CCENT?
-
ICND1, question mark and non english keyboard
Hi guys, is the question mark allowed in simulations during the exam? If the test center use a non english keyboard is some configuration needed? I found a post where it was said that you need to ask the testing center to configure the PC with only the US keybord layout and then use the key in the keyboard that corrispond…
-
Lab question about ip services on 3356g
I thought I understood from Cisco literature that WS-C3560g-24ts-e includes an ip services license but many of the models on eBay look like look they run the base image. If I buy an e model that doesn't come the ip services image, and I install the ip services image should the fact that it's an e model mean the ip services…
-
CCNA exam simulator.
Hi, I am using physical lab and packet tracer labs for studying for CCNA, I was just wondering if the simulator in the exam looks something like the packet tracer?
-
SCYBER vs CCNA:S vs CCNP:S
For Security Analysts doing intrustion analysis, incident response, security assessment and auditing, etc., which of the Cisco security certs is the "Goldilocks" fit for this role? We do enterprise security and in a pure-Cisco environment with ASAs, VOIP, VPN, Wireless, etc. Our Network team administers all the above, and…
-
Lab question: what interface cards do I need?
Started acquiring equipment for my lab and picked up 2 2621XMs but they didn't come with any add-on cards. My goal is to purchase what is necessary to get my CCNA so what add-on interface cards should I pickup? Thanks in advance all!