-
IP/Subnetting Questions
Hey all, First, I apologize if this is the wrong forum for this particular question. I looked around and did not see a Packet Tracer sub board. I'm working on my final project for my first semester CCNA class, and it's a packet tracer activity. I've finally gotten my head wrapped around the basics of IP routing and…
-
Inbound and outbound question
Hi, so I have a cloud setup with an access list that permits icmp traffic and tcp traffic on ports 80, 443 and 23. Everything works from my PC that I'm testing it on in GNS3. However! I initially put it on the outbound part of the interface and nothing work but then I tried the inbound option and everything works…
-
Access list question???
Hi I have 3 vlans set up in this topology and a cloud with a loopback address of 8.8.8.8. Vlan 10 Vlan 20 Vlan 100 Without the access lists they can all ping each other fine and can all reach the loopback to. Here are the 2 access lists: Vlan10 Permit ip any 10.10.20.0 0.0.0.0 (for vlan 20) Deny ip any 10.11.100.0…
-
210-260 and CCP
Hello everyone I just got the new book ,,,,I didnt check it all but I saw a lot of images in the book about CCP ,,,I heard some people says that CCP is not required in new exam ???
-
ICND1 practice tests?
Hello all, So i have been studying for a while and i want to see where i am at and what i need to brush up on. Does anyone know any good practice tests i can use? I currently have Boson but i am honestly starting to see the same questions over and over and I am starting to memorize them which doesn't really help me as far…
-
ICND2 Tomorrow!
Hey all, Sitting for ICND2 tomorrow. I took it a week and a half ago and failed horribly (595), mostly because I ran out of time. Since then I've been brushing up and taking practice exams through Transcender. Fairly nervous, but at the same time I want to get this over with so I can move on to bigger and better things.…
-
Inter-switch heartbeat
Hey guys, is there a feature I can setup on a 3750G that allows me to make like a heartbeat connection for the sole purpose of STP root bridge selection. Like in my mind if I have a core switch, being a 3750G, that is the root bridge, if it goes down and it's the root bridge it has to then select a different core switch to…
-
Real World scenario?
what would happen if there was a new lsa and ospf topology changed during a massive data transfer. would the data be interrupted? since lsa happen every 30 mins, how would the convergence effect normal data stream. would the path change? it would have to if a router went down?
-
New Security Exam
I saw on CLN today, last day to take the current Security Exam (640-554) is Nov 30. The new exam (210-260) starts 12/01. I checked on Cisco Press, they don't have any new books available. Pearson Vue does have the new exam available - $250.00.
-
Need Help with CCP Error
Hi All, I am facing issue with CCP - GNS3, i am using GNS3 for configuration - 1. Router 2. Switch 3. Cloud (Microsoft Loopback Adaptor) but when i use it i am not able to discover the device in CCP. Screenshot attached. Please help me to resolve this issue, i have CCNA Security Exam next week i need to some practice…
-
UK CCNA student.
Hi! From the UK and studying for the CCNA. I have been studying for a while on and off but decided that I need to make the effort and get my backside in gear. I am already a memeber of a Facebook CCNA group and have been getting support from them. I have also joined this forum in order to gain more knwoledge and get…
-
CCNA Data Center?
Hey All, I am about to finish the CCNP Security. I have one more test left which I'm hoping to be ready for before November. I was thinking about doing the CCNP R\S after that, however I work in a Data Center which is HEAVY on UCS and Nexus is starting to make it's way into our Data Centers. Therefore, I think switching to…
-
CCNA Ready?
Hello Guys, First of all thanks for accepting me in the forum, this is my second time here visiting you guys, and i just took the CCNA practice exams that you guys have available. (no brain ****) first attempt, below my scores, do you think that im ready to take the CCNA? this is my first taking a certification like this,…
-
Default static route & EIGRP
If we define a static route ip route 0.0.0.0 0.0.0 ....... To inform other routers in OSPF we have: default-information originate. For EIGRP is there a similare command? I've seen in some example the use of: redistribuite static but it seems to me that is a very generic command to redistribuite ALL the static routes, not…
-
A Router Into a Switch
Hello, I have an 1800 series router, it has 2 interfaces attached to it, what I would like to do is to make it behave just like an ordinary switch, and since the "switchport" command didn't recognized on those interfaces configuration I couldn't figure out what to do ! Thanks alot for any clarification !:)
-
Any ideas for an "isp" in gns3??
Hi, I have configured 2 different site networks in gns3 with vlans etc... Both sites connect through a serial link but i also want to create an "isp" or "internet" cloud where the user's on 2 sites can ping out to an Internet address such as 8.8.8.8 and have it reply! What is the best way to do this?? Would a router with a…
-
Serial point to point connections question?
Hi, can someone please explain to me how serial point to point connections work or can someone verify that I have gotten this correct and what I have got incorrect? So, you have a router at both ends that are the DTE and they connect to the DCE modem that specifies the clock rate that needs to be the same. The routers are…
-
210-260 Study Material?
I will be completing my CCNA in the next few weeks (if i pass ICND2) and would like to move on to CCNA Security. I figure there's no point in trying to cram the current exam and would like to begin studying for the new version of the exam. Has anyone been able to find material to study other than the official cisco book on…
-
HDLC question
I wanted to ask a question about hdlc. I can't wrap my head around just exactly how it works, the in depth version of it? I know the basics of what I read, it communicates to serial leased lines together, but HOW does it do it? How does the isp get involved in the middle and how can one side be a dte and another be a dce…
-
Sdh
Hi, Does anybody know where to read up or get knowledge on sdh/dwdm? Preferably a simulator would be better. Unfortunately there is no forum section for this
-
Communicating on a wan link
Hi, in my topology I have 2 different "sites" set up in GNS3. I have a router in the middle acting as an isp and I have a router at both end points of the sites. I would like to know what is the best way I enable them to communicate across the "isp"?. I can post a pic of the config if you guys want but I'm not sure if I…
-
Why isn't my switch doing arp???
I've successfully configured a router on a stick topology in GNS3 but my switch connecting to the router and the pc's is not displaying the arps of the other devices when I use the show arp command! I find this odd because all the other devices are displaying the arp's and everything is working to! Any idea as to why this…
-
CBT Nuggets worth it for CCENT/CCNA?
I just wanted some real opinions here of people that have used CBT Nuggets in their studies for CCENT. I would like to know if it is worth the cost as I am sort of limited on what I can spend right now on my continued training on getting my CCENT. I already have a subscription to Pluralsight/Trainsignal and their CCNA…
-
GNS3 0/0 -1 Port range question
Hi, I have set up a topology in GNS3 and I want to configure trunk ports, the only thing is that I can't configure them for the 0/0 -1 etc.... They can only be set up using 1/1 - etc.... is this normal or am I doing something wrong? Thanks in advance!
-
Subnetting Question
Here is the diagram: What I am trying to accomplish, is create a route to the network in the colored square from Router2. On router 2, which I have telneted into, I am entering the following: R2(config)#ip route 172.16.4.9 255.255.255.192 172.16.4.6 %Inconsistent address and mask The routing table in R3 is as follows:…
-
Cisco Eithernet devices and switching
We all know that all the devices on a network connected by switch. So if a printer connected a network by Cisco switch then all the computers on this network can use this printer automatically without any configuration? Or any configuration is needed to use this printer. Not only printer asking all eithernet devices such…
-
CCDA / CCDP Exam Update
Last day to test is December 14th. This puts on a little pressure for my CCDP studies. CCDA - DESGN: CCDA - IT Certifications and Career Paths - Cisco Systems CCDP - ARCH: CCDP - IT Certifications and Career Paths - Cisco Systems
-
Need More SFP Information
Blue patch cord can be used for Single mode SFP Orange/ Green patch cord can be used for multi mode SFP. I heard that there is an exception but that the speed will be lower. Which is it?
-
Etherchannel and switching loop
Hi guys, I'm having a hard time understanding how layer 2 switching loop is prevented when using Etherchannel, I read that STP dont block port channels and thats caused me a lot of confusion. For example if we have three switches and each switch is connected with the other by four links (we create a port channel out of…
-
GNS3 question???
Hi, I want to be able to access the console terminal for hosts on GNS3 but there are no consoles for host machines on GNS3! Would the answer be to simply create an etherswitch and change the icon to a desktop? I can't see any other logical way! Thanks for the help guys
-
IPV6 issue to ping from Router A to C
Hello Geeks, I am preparing for CCNA reading Lammle's book I follow instruction on the book but cannot ping from Router A to Router C. See my Diagram . If am doing process with ipv4 is ok . IPv6 is giving me problem. Here is configuration. Router B has two subnets int f0/0 is configured ipv6 address 2001:db8:3c4d:1::1/64…
-
Ccna
What online work from home networking projects can I get after completion of CCNA ? What will be the pay for it ?
-
Lammle CCNA R&S Deluxe Study Guide Chapter 6 Review Question help
I'm using the deluxe study guide, no mention of an edition that I can see. I've Google'd errata and found some but not regarding this particular query. On page 278 question 3 in the chapter 6 review questions it reads as follows: 3. Which two of the following commands are required when configuring SSH on your router?…
-
Ccda10?
Is anyone else seeing their CCDA certification listed as CCDA10 on their official transcript? I'm not sure why it's reporting with this weird name and just trying to figure it out before I go down the Cisco support rabbit hole.
-
packet tracer no ip routing command
Hello, I'm studying for CCNA. I'm working through an INE lab that wants me to put in no ip routing but none of the routers I have in packet tracer work so I don't understand what to do next. I tried it on a 3560 switch that is in packet tracer and it worked there, but it wont work on any of the routers. Thanks. From the…
-
How can i solve these kinds of questions ?
interface FastEthernet1/1.3 encapsulation dot1Q 3 ip address 192.168.0.129 255.255.255.192 interface FastEthernet1/1.4 encapsulation dot1Q 4 ip address 192.168.0.193 255.255.255.224 You plan to add two new VLANS: VLAN 5 and VLAN 6. VLAN 5 should support 19 hosts, while VLAN 6 should support 3 hosts. Which of the following…
-
CCNP Switch Study Strategies :)
Hey guys I just started studying for the CCNP Switch exam Will do Switch > Route > TShoot in this order to get my CCNP At the moment I have as resources CBT Nugget videos CCNP Official Routing and Switching Cert Guide book GNS3 Packet Tracer Couple of 2960 switches at work and have to find a spare layer 3 switch at work if…
-
Looking for advice for CCNA 200-120
Hello! I have passed the Cisco CCNA Academy and I am preparing for the 200-120 exam. What areas will the main focus be on? I am currently using Cisco Press's icnd1 and icnd2 cert guides to study. It came with software that has very useful practice questions that cover every area of icnd1 and 2. I would like to narrow down…
-
Good training video source for CCENT?
I'll be taking my VMware VCA6-DCV this week, then I will be starting my CCENT. I looked on the Cisco learning center store, and this appears to be the training video for CCENT: https://learningnetworkstore.cisco.com/ccent/cisco-e-learning-for-icnd1-v2-0-180-day-subscription-elt-icnd1-v2-0-015601 No F@CKING way am I paying…
-
ospf cost, bandwidth
Could someone kindly explain. auto-cost reference-bandwidth 1000 and ip ospf cost commands in ospf I am assuming the first command specifies bandwidth and the second one specifies cost directly. cost =10^8 / Band Width.
-
Certification renewal question for old CCNA to new
My CCNA renewal is coming up in July of next year and since I'm lazy, I figured I'd just renew my existing CCNA instead of going for another CCNA-level cert. My existing CCNA is from the older CCNA material. My question is whether or not I can simply take the new/current ICND2 or if I have to do the new ICND1 + ICND2 or…
-
Failed 640-554
Just failed my 640-554 exam. I have rescheduled it for the 30th of this month. I am currently already certified in CCNA Security via 640-553, but all of that expires after the 30th as well so I have to take it again. It said a passing score was 895 and I got a 756. There were a lot of questions that I don't remember being…
-
Passed - 100-101
hi guys, dont post much, but thanks to all that helped. passed today, but says something about indeterminate until they can verify. got 867 as a score, took just over 1 hour to finish. onto 200-101 now.
-
ICND2 Failed
Just took ICND2. Failed epically. Started off great with 5 or 6 softball questions, then I got to a sim and brainfarted on the commands. Ended up spending 15 minutes on that sim alone. I know what I need to study and i'll knock it out of the park next time.
-
Ccna 200-120
I´m studying for 200-120 exam, and one of the materials I am using is the Boson 200-120 practice test. There are many Frame relay questions there, are there many questions on that subject in the real test?
-
Renew CCENT
If I take and pass CCENT (ICND 100-101), I know you can renew it and get your CCNA by taking ICND 200-101. But what if you wait 2 to 2 1/2 years and the ICND 2 exam has been refreshed and is call 200-102 or something. Will that still renew the CCENT and upgrade me to full CCNA?
-
Do I have to memorize of 2 for CCENT subnetting ?
I am wondering that if I should memorize power of 2 and how far show I go if I got a question about Class A network which is required too many host ,, any idea or help please guys .... Thank you
-
CCNA Lab Routers
Hi Guys, I've been building my CCNA Lab and have currently got the following Routers: Cisco 2821, Cisco 3745, Cisco 2620xm - Faulty ethernet port but otherwise everything else works. Switches: A bog standard 2950-24 2950G-48 and a 3550 emi. I'm wanting a 4th router so I can use one as a frame relay switch, I've the option…
-
Cisco has decided to retire the 640-554 exam
Hello guys. I bought the 640-554 exam on Pearson VUE some days ago, and today I received this email from them: Someone know what's happening with the CCNA Security Certification? A new exam version? Certification discontinued? Should I present the exam? I'm CCNA Routing & Switching certified. If Cisco is going to…
-
Obligatory I passed thread.
Don't post here too often, but I do lurk quite often. Just wanted to say thanks to every one on this board as the posts here have been very helpful. So I studied for a little less than two months, using the OCG, CBTNuggets, my personal lab and of course here. Passed the ICND1 today with an 867, wish the score was higher…
-
CCNA Security Virtual Labs?
Hey guys Wanting to start to study for the 210-260 CCNA Security I got the book on order, but does the book have virtual labs you can do? If not can anyone share some or tell me where I can get some relevant to the material
-
Packet tracer 6.2 issue cisco 2811 with HWIC-AP-AG-B
Hi geeks, Could somebody help me wireless issue I have in packet tracer 6.2 I want someone let me know if his packet tracer 6.2 having same problem so this is my scenario see bellow configuration when I select dhcp it gets APIPA.Could someone help me please? What I am doing wrong Thank you Guys in advance.
-
Packet Tracer Question
After really getting back into studying since I have been busy with school work and finding internships, I'm now really getting to the labs as I continue to keep reading through Lammle's book and doing the labs in there, but for the Hands-on Lab 6.6, I'm trying to add an IP address in the interface of the router I'm using…
-
CCNA/CCNP physical lab
What type of switches and routers would you buy for your CCNA physical lab that you can also use for CCNP? the budget is 600$ :)
-
ICND2 or CCDA
From what I have seen on the Cisco site, you can pass the ICND1 and go directly to CCDA. Is that a good idea? It seems to me that it would be a good move, because everyone seems to be going for the ICND2, so having the CCDA would make you stand out, I would think. I'm also thinking about taking the CCNA Security. What do…
-
Switch & Multicasts
I was wondering how a switch treat a multicast. Does it flood the frame in all the ports or does it knows in which port there is someone interested in a particular multicast address? If it knows, how?
-
How long to study for and pass CCENT
Hi all. I am new to networking and am studying for my CCENT cert. Been studying for the past week or so. Was wondering if someone out there could tell me how long it would take to learn and pass the ccent. I understand that people learn at different speeds and such so put it into perspective abit I study about and hour or…
-
I can't take it anymore with this ICND1
being scheduled Thursday. I just bumped it to tomorrow at 12. It's like waiting for Christmas as a child, but I have the power to change the date. Heck, I have changed it to today if I could have. My anxiety is just getting worse and I fear I will implode if I wait until Thursday. I keep getting high 90s on the Boson exam,…
-
Question on Layer 2 switch logic
Question: How do Layer 2 switches handle a conversation between two computers pointing at each others IP addresses, since the switch will only be able to handle layer 2 information? Do PC's store what MAC addresses correspond to destination IP's? I was curious about this because it occurred to me that if I were to ping…
-
Cisco 100-101 Flash card book questions
Hello all, I am currently reading the Cisco CCENT ICND1 Flash card and Exam Practice book and I have a run across two things that I have not seen in Odem's book or Todd Lammle's book. On Chapter 8 Question 34 page 271. What Cisco IOS command displays open ports and services on a cisco device. Book Answer: show control-plan…
-
Question about Boson practice exams for CCENT
Hello everyone, have a question regarding the Boson ExSim-Max for CCENT. I am almost at a point of wanting to purchase the practice exams to start going over but for anyone that has used this, is it worth spending a little more and getting the "kit for CCENT"? that comes with NetSim 10 and appears to have labs included. I…
-
CCENT / CCNA Lab workbook
Hey guys I'm in the process of writing a comprehensive lab workbook for CCENT and then CCNA. What do you guys think, Is it worth the effort? I'm currently unemployed so at the moment I'm thinking of selling it for $2.99 and hopefully I can give it away for free in the near future. All your suggestions would be greatly…
-
the "ANDing" concept
Hello. Is ANDing a must to memorize for either the CCENT or CCNA exams?
-
CCNA Wireless
Has anyone taken the wireless exam lately?
-
Ccent
Hey! How hard is ICND1? Do you have to to know how to subnet in literally 20 seconds? That is something I need to practice but how can you even be expected to write out the entire range of IP addresses in that amount of time? Other than that what should be expected? Is it: 33% theory 33% subnetting 33% cli? Thanks
-
Serial interface no clock
What happen to a serial interface (DTE side) if it does not receive a clock signal? It goes up/down or it remains up/up? Sometimes real hardware is needed to test certain things Can anyone try and post a show ip interface brief? Thanks.
-
I am confused (IP Conflicts)
All, I think I'm making a noobish mistake here. I have multiple sets of VM's in a ESXi stack, Each set is assigned a different VLAN but each set of VM's have the same IP address. On the physical switch I didn't configure a gateway or anything. It is strictly layer 2, no inter vlan routing at all. One of the VM's (Windows…
-
How to view a routing loop?
Using real equipment, how do I view a routing loop? Debug? Thanks
-
210-260 Hardware Requirements?
I need to recertify my CCNA, and was going to take the Security exam soon. Is there any hardware that I would need to purchase to complete the objectives for the new exam? I don't have a long time before the expiration of my CCNA so I need to get the ball rolling asap. Thanks!
-
Help config cme and sw
I am trying to config cme on a 3825 router. I have one dhcp pool for data and would like to make one for voice on the same gi0/1. I was told by someone to use gi0/1.1 for voice. and then i would be able to make the dhcp pool network 10.90.0.0 255.255.255.0 gateway 10.90.0.1 then go back to gi0/1.1 and put the ip address in…
-
pppoe
Can two router be connected via pppoe without internet
-
Packet Tracer 6.2 PKA's
Couple of questions: Will Packet Tracer 6.1.1 PKA's work with 6.2? (PKA's are the packet tracer labs) Does anyone know where to get 6.2 labs? I have all the labs required for the CCENT, for Packet Tracer 6.1.1. But I get a warning when I start it up now, and Cisco says that is due to a certificate expiring in 6.1.1. It…
-
Wireless, GUEST and STAFF
Hi everyone. I need your help badly. We have cisco aps and wireless controller and we are about to deploy it tomorrow. Currently, our client has a FLAT vlan design and they require us to create Wireless network for GUEST, STAFF and VIP. Guest wireless should not have access to the internal network.. Now, is there a way to…
-
PC to Router - Straight Thru or Crossover?
Hi Everybody, I think i see conflicting answers in practice tests. Does a PC to Router need to be a Straight Thru or Cross Over cable, not for consoling in (roll over). Just general connectivity. Thanks
-
STP Seriously?
There is just SO MUCH information that STP uses. I feel like I'm regurgitating the book on paper lol.
-
Question about ports
Hi, I have a question about ports that I'm a little but confused about. If a router has blocked nearly every port except port 80, 135 and one more, why is it that I can watch stream videos online if they use ports such as 554 etc... I don't understand that. If you're clicking on a link for example that will require https…
-
Q about DR/BDR election
Hola, So, i have a question about the election process. Assume this scenario: R1: IP address- 10.1.1.1 R5: IP address- 10.5.5.5 ~ If all other factors were equal.... then we would say that R5 wins the DR. But What if i throw a curveball: R1: 10.1.1.1 Router-id: 10.10.10.10 R5: 10.5.5.5 Router-id: 5.5.5.5 Q1) If both…
-
Can't Ping PC ---- SWITCH -- SWITCH to Router
Greetings My fellow Scholars, I'm Fairly New to networking and trying to understand things better. Using packet Tracer, I created a network Topology where I'm trying to ping one of the six PCs to the Router or by-versa. The problem is that is not working for me. Each PCs can ping each other but not the Router itself. Below…
-
Instead of getting CCNA: R&S how about?
I'm thinking ahead here, I'm currently studying for the ICND1 and my goal is to have my CCENT by the end of the year. I've noticed that most people afterwards do the routing and switching exam so they get their cCNa in routing and switching. But at looking at all the other tracks Cisco offers, I'm wondering if it wouldn't…
-
Passed my CCNA today with a 917
Hey Guys, Passed my CCNA with a 917 / 1000. Free MCTS MCITP CCNA CISSP and Network+ practice exams, study notes and forums has been a fantastic resource for finding those questions I want answered. Materials used: CBTnuggets , official Cert guide by Wendell Odom, GNS3. (Lots and lots of GNS3/CBT).
-
Passed CCENT today
After two months of procrastinating, I finally took the test. Really felt unsure going into it, but once I started the exam I felt pretty good about it. Now I just need to decide if I want to go for CCNA Security or CEH. Don't think I'll bother with CCNA R&S as it doesn't interest me at all.
-
Passed icnd2 on the 1st!
Hi All, Passed the test with a 854! A pass is a pass :) study material: CBTnuggets, the official Cert guides, GNS3, Network simulator from Cisco (don't remember the exact name) One thing I will say is they threw everything at me. You really do need to know all of the topics in the blueprint at a very detailed level. see…
-
passed ICND2 today
894 my biggest problem: time I finished with a grand total of 40 seconds left ... pfuuuui Good luck all!
-
CCNA/CompTIA Security+ Jobs
I am graduating in spring with my Associates in Network Technology. I have no prior experience in IT. I'll have 2 certifications by then. I am curious though. Once I graduate, without any prior working experience, what kind of position could I possibly apply for and get with my CCNA and CompTIA Security+ certs??
-
Difficulty Understanding the Lingo
Now maybe this is because I just started my Cisco classes in school but going through all the threads on this forum and reading all the discussions it makes me a feel a bit intimidated. You are all using terms and phrases that I never heard before and not sure if my classes will cover all of it. I see reference being made…
-
CCENT Exam in October - Which book should I use?
Should of read the forums. Sorry about that. Mod please delete.
-
Likely Taking the CCENT in Early October, Need Lab Advice
I'm currently majoring in computer information systems at my university and am graduating next year. I recently started studying late last month for the CCENT certification starting out with Jeremy Cioara's CBT Nuggets videos and completing all of those, which really got me excited about wanting to learn more about the…
-
Failed CCNA Wireless Today
I went and took the CCNA wireless today. It was a lower score than I was expecting 730 needing 790 to pass. Of course as I was going I was trying to take mental notes of questions I was unsure of, and of those there are several questions that I verified I answered right, and the others I cannot find in either the Cisco…
-
Help with Exercise
Hi, guys. New and noob here, I don't know if this things goes here, if not, I beg you pardon and please move it o delete it. I need some help with an exercise from a series of 14. Find 5 basic problems with this network topology and explain the actions that would mitigate or remove them. Thanks a lot in advance, I know…
-
Any females on here?
I did search and see a couple posts about females in the Cisco forum. Mainly replies in posts. It is very difficult for me to admit my interests in technology. I've only met a few females with the same interests. One thing that has caused me to be very shy about sharing my interests is I was knocked down by a male TA when…
-
Problems with CCP
I start with GNS3 ,,,it was ok but when I go to check on Security or IDS it takes along time then its says that ((the connection has been lost )) I bought a router Cisco 871 ,, and I have the same problem should I configure the firewall on the router first ?? and suggestions please
-
My ccna exam results, needing troubleshooting advice
Hello all, I sat for the CCNA Exam yesterday received a 785 needed a 825 my break down is as follows: LAN Switching - 91% Routing - 86% IP Services - 0% Troubleshooting - 53% Wan Services 70 % Granted that IP services is only 6% If I missed 3 of them its 0% so I am not overly concerned on this one. My problem was…
-
Composite vs ICND1 & ICND2
I was reading around the web and I've seen a lot of people recommend taking the composite exam as opposed to the two test route, and the main reason is because: When taking the composite, you only have around 50 questions. Within those 50, a lot of them could come from ICND1 topics which are easier than ICND2 topics.…
-
CCNA Security after CCENT
I am in a bit of a bind for time here. I just passed my CCENT a couple days ago, and part of my degree is obtaining the CCNA and CCNA Security. Considering the CCNA Security is retiring December 1st, and the new one will be out, how long does new material really take to surface? I emailed my student mentor with my concerns…
-
CCNA Security 9/3
Going to take the CCNA Security exam on Thursday. I'm really nervous. Has anyone taken it recently? Does anyone know the minimum passing score? I also heard something about the NSA giving a letter or a cert? Not sure how its recognized. Thanks
-
Request for suggestion
HI guys, WIth CCNA R&S in my bag i would like to push my self further deep. I myself wanna be a security consultant someday also I am a fresh graduate student with no experience. WHich certificate do you think would let me break into industry. What do you think CCDA or CCNA sec . Please provide me your valuable…
-
How to select only either odd or even ports in a cisco switch
E.g odd ports int ran gi1/0/1,3,5,7,.... Is there an easier way of doing it other than typing in all the port numbers one by one?
-
Prefix Delegation is killing me
Hei gents. I was trying to migrate to IPv6, but I am getting some issues with DHCPv6 and subnetting. DHCPv6 Stateful implements prefix delegation that does not seem very obvious to me. I have created a pool on R1, which as act central DHCP/DNS R1(config)#ipv6 local pool CustomPool 2001:db8:12:1250::/60 64 ! My overall…
-
CCNA in 2 days
Hi guys.. I have CCNAX on sep 1st. Any last minute pointers or suggestions. Regards Nans
-
Old Lammle CCNA book, versus new Lammle CCNA book.
Hey everyone, I passed the CCENT! :) Now im ready to start my studies for ICND2. I have the Todd Lammle book for the previous version of the CCNA, the old 604-802 exam, the one before the 2013 update. Now of course im studying for the 200-101 exam. the only major differences between the two exams I am aware of is dropping…