-
How Many Subnets and Hosts Per
I've been studying with SubnettingQuestions.com lately (and getting most of them right! :D ), but I seem to have trouble whenever I'm thrown a question like this... How many subnets and hosts per subnet can you get from the network 172.30.0.0/23? ...with a CIDR of /23 that would make the network increment in 2s, right?…
-
Subnetting class A question, WHY -2
Why clas B and C networks dont require -2 to calculate number of subnets, but Class A esquires -2 from the total? I tried to look up for that, but i couldnt find any other resource showing this. I got this info from Odom`s book. I am pretty well with subnetting, but this confused me. I have the ICND1 exam scheduled Nov 11,…
-
question about ppp encapsulation
i understand if the encapsuation on both sides of 2 routers serial links do not match then if you ran a 'show int s0' command the output would 1st show that "serial 0 is up, line protocol is down". However if both sides were set to ppp encapsulation but only one side was set to 'ppp authentication chap" would line protocol…
-
Packet Tracer Activity 3.22
How can you check for answers for these? I'm trying to do these on my own but there are no answers... Anyways, it wants you to add static routes from the ISP but the one they gave you makes no sense ISP(config)#ip route 192.168.1.4 255.255.255.252 172.16.1.6 the link to the router is 172.16.1.5 i tried adding static routes…
-
Packet Tracer - what am I doing wrong?
Hi all, Just going through CBT Nuggets ICND1 at the moment, labbing away with Jeremy. Anyway I'm running Packet Tracer 5.3.3 I can't seem to get static routes or RIP to work correctly - they don't save in the configuration. For example: I grab 2 generic routers, link them together with crossover cable (from my…
-
Finally Passed ICND1
Passed ICND1 yesterday with a score of 825. Now moving onto ICND2. Have people found ICND2 harder to learn that 1. I am assuming it is alot of the same information just extending the knowledge so i wasnt sure if learning it from scratch people found harder than adding extra knowledge of the topics. Thanks
-
2620xm purchase decision help
Hello, I just have a question before I purchase a cisco 2620xm router. I currently have 3 2500 series routers and want to implement vlan trunking to my 2950 switch. I just wanted to confirm that there is no AUI adapter that supports FastEthernet that would enable me to trunk with my current setup. Thanks
-
ICND 2 VLAN and VTP questions
Not sure if this would be more of a CCNP question, but here it goes: The book says each VLAN must be on its own subnet, which makes sense since it's a broadcast domain. My question is: Assuming I have a VLAN called Production, but the company has 2 branches in San Francisco and Boston (each branch has a gateway router,…
-
ASA 5505 instead of a 5510?
So Im looking to buy an ASA. I bought the CCNA:Security lab manual (1.1). It's using the ASA 5510. Do you think I can get away with using the 5505? I've searched on the websites for the differences- but all I can discern is that the 5510 has an IPS module. ...which in all fairness isn't any different than what the OCG is…
-
Looking for Advice on starting my CCNA Journey
Hello everyone, I am new here and this is my first post. I’m about to start my CCNA journey. I have a little experience with networking but still miles to go like learning to subnet or use an industrial router (I’ve only used SOHO routers.). I really need some advice about a couple of products and what path to take. I’m…
-
Can it be done? Ripv2-FR-OSPF and HOW?
Hi, Im in the process of configuring a lab testing my skills and ive hit a brick wall. Basically i have one working internetwork running RIP and one Internetwork running OSPF. I tried linking the two together via a frame relay link but im finding it a bit difficult. I have configured the end routers on both internetworks…
-
Another Recommendation for Switch (Home Use)?
Yes I know another post asking for a recommendation for a switch for home use...lol This is actually not so much for training as it would be used for my POE devices (IP cams / and the possibility of adding phones one day) Anyway, I was thinking along the lines of a 24 port for future expansion....I already have 8 cams so…
-
Can i connect Console cable to Wifi router ethernet port using converter?
Can i connect Console cable to Wifi router ethernet port using converter? I am trying to connect the terminal server to wifi router using console cable so that i can access the router and switch using wifi but i need to know whether it works if i connect using the converter (RJ45 to DB9 male). Please guide me Many Thanks…
-
GNS3 CCNA- CCNA Sec
Hi, Can you effectivly study for CCNA- CCNA Security with GNS3? I saw that there are limited supported devices, and I didnt see ASA in the list. Does it support CCP? Well, I just found out that GNS3 doesnt support switches. (I know the functionality is there, but I really prefer the simulation.) I'll keep the question open…
-
Which switch should I buy?
Hello everyone, I ld like to hear your suggestions about which (hmmm please CHEAP really really CHEAP :P!) switch to buy for my CCENT + CCNA studies. Since GNS3 (correct me if Im wrong) does not support a way to load IOS images into switches [although I think that you can use a router as a switch.. but i dont like this…
-
I know this is going to seem like a stupid question but...
i'm having trouble figuring out cisco's way of denoting memory sizes. On my switch is says it has 21295K bytes of memory. cisco WS-C2950-24 (RC32300) processor (revision R0) with 21295K bytes of memory Now are they saying 21295 thousand bytes or are they saying K as in KB? And I want to confirm this is the amount of RAM in…
-
what is the frame relay switch used in GNS3? (confused)?
Is their a model number for one of these? are they currently in use? I just did a GNS3, frame relay lab, that use a frame relay switch. This configures differently than a router, that is used as a frame relay switch. (it was much quicker to configure). I google, (frame relay switch ) and nothing realy indicates that their…
-
Shifted to 3rd gear today!!
CCENT passed, 925/1000. I did not waste any time and downloaded the Boson ICND 2 Ex-Sim and already working on it. Being that I took the 640-802 already, I have most of the stuff nailed down, but I will use the same formula I did, and that's scoring high on the practice exams and doing my labs. My goal is to have it before…
-
Why can't i get ripv2 to work?
I can ping the routers between each other but i am unable to ping the pc's that are on separate networks... here is what i have for the config's for the routers... can someone tell me what im doing wrong? LabA router rip version 2 network 201.100.11.0 LabB router rip version 2 network 199.6.13.0 network 201.100.11.0 LabC…
-
Passed ICND1
Took and passed the ICND1 exam this morning. It was harder than I was expecting, but I ended up with (I think) a decent score. Got an 899. I'll take it.
-
ip inspect tcp max-incomplete host xx block-time x
Hi All, What does the above do in simple terms? Easy to understand...just came across CBAC. I had a look online but not really understanding it.
-
Question about ICND1 coverage of Link state protocol.
I was going thru Boson ICND1 practice test that came with my ICND1 book. there is a question about characteristic of Link state protocol. And answers are They build topology table and converge quickly. I know that link state protocol converges quickly from ICND1 chapter 14 of odom`s book. But there is no mention about the…
-
Every single time! broadcast storm....
Ok well as im studying for CCNA been messing around with a few topologies and of of them ive been trying is the following: S1 to S2 S2 to S3 S3 to S1 so a triangle like topology, but i have 2 links running to each switch, each time i set this up i think im creating a broadcast storm, but PT keeps freezing on me, so i cant…
-
When is CCENT/CCNA due for the next version renew?
Hey all, Just a quick question, when is CCENT (ICDN1) or CCNA (ICDN2) due for its next version renew (A new version of the exam comes out). Just wondering as I am studying for the exams now and looking to book. Cheers.
-
Forced Access Code's
My company wants me to set up Access Codes for long distance calls, everything im finding requires manual configuration through our UC500, anyone had to work with this before im assuming with the amount of knowledge on these forums someone has. If someone is willing to help up could you please IM me?
-
Were you ever stuck in 2nd gear and redlined your engine? (this isn't a car post....)
I was.......very few times in my life. This is the best way to describe the CCNA in my very personal exerience. I'm trying to find the "light at the end of the tunnel"........... I started in 2010 with 6 months of studying and a bootcamp, $2300 later, I did not pass, scored 650. I then decided that the bootcamp was a waste…
-
What to write down before the exam
What did or are people thinking of writing down on the blanks sheet of paper, before the exam, i know a lot of people write subnetting charts, But i feel quite confident with subnetting. I was thinking of just writing down the networks in 16s, as sometimes its hard to remeber your 16 times tables. Does anyone have any…
-
Last Lab before I take the Exam
Ok, Im selling my UC520 and moving on to the full CUCM/Unity Connection server setup. Here is the new Lab and need to know if Im missing any thing? Taking the Exam in December but I need more seat time on the CUCM server. I use one every day at work but I never configured one from scratch. My goal is to build a Enterprise…
-
Rogue's CCNA:Voice Studies
So I might as well start going for my CCNA:Voice. I'll come back to CCNA:Security, but for the mean while, this book has been calling me too much. Initial Plan: 1 Chapter each day. Notes Plan: First Run Through: In book. Second: In Notebook Third: OneNote Lab Plan: Not a darn clue! Test Plan: Not a darn clue!
-
STP Root Port role election criteria - With Picture!
Hi Again- (I tried attaching the related topology last night but lost my connection to the site). (Topology atachment below) In my course material, I've not found much detail regarding election of a root port other than "The root port is the switch port with the lowest path cost to the root bridge" they also expand on this…
-
How do you simulate NAT in packet tracer and GNS3?
Hi everyone! how do you simulate NAT in both packet tracer and GNS3? thank you! :)
-
Odom or Boson Lab Sim
Hi All! I have been studying for CCNA/CCENT for a few weeks now, and I think it's about time I got some hands on experience configuring equipment. I first considered building a lab, but it seems that it is problematic to get the proper equipment with the proper IOS images, so I have been looking at lab sims (which are also…
-
When Packet Tracer is missing a command
For those of you using PT exclusively, what are you doing when PT does not have one of the needed commands?
-
.pkt file can not be posted in this forum?
Hi FYI, the sbject line. I am novice CCNA aspirant and I am trying to post one .pkt file from my packet tracer simulator. Jut wanted to know first why it is not allowed? Or I am doing somehting wrong? Thanks in advance. BR//O
-
Online CCENT Practice test
CCENT Practice Certification Exam # 2# Here is a pretty good timed online practice test for CCENT. The questions are very well written and thought out. It will give the answers after you answer the question but does not give explanation. At the end it will ask you to log in or sign up for an account. I balked on that part.…
-
question format
Hi, reading an ICND1 book, and for the first few (do you know this) chapters the book would specify "choose two answers" or "choose three answers" In the latest chapters many of the questions didnt say there were multiple answers, but would say "commands" vice "command", causing me to choose the most obviously needed…
-
Knowing the Interfaces
This question has been bugging me for a while, I mostly use packet tracer to configure networks but from time to time i forget which interface is which. Is there a way of checking an interfaces on a router in CLI if there is just a cable connected to it with no configuration? there will be times when i connect up a cable…
-
Why cant i add this static route in r3?
R3#show ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS…
-
Scheduled 640-822 ICND1
Scheduled it today for 11/5, wanted to shoot for end of October but didn't want to take it in the middle of the week so I had to push it 1 week away. Plan is to pass it on the first try and then schedule/take ICND2 before the end of the year. What I am using- Todd Lammle's CCNET Study Guide: ICND1 Subnet192 icnd1 guide…
-
PLS HELP i have CCNA doubts
1)Why IP Standard list is as close as possible to destination,and Why IP Extended list is as close as possible to source 2)What is load balancing 3)What is IP Subnet zero 4)What is Auto and Manual Summarization and discontigous network] 5)What is delay line 6)What is Equal-cost Path
-
Standard ACL help
Hey guys, I'm having a little issue with an assignment. I attached a picture of the assignment. I blocked Kevin and Sally from accessing GOOGLE with standard ACL. However, it's also blocking the MSN as well. Can you give me instructions on how to block GOOGLE only and not the other connected devices Here is the following…
-
Removing fans from lab setup?
I believe I saw someone posted on here that they removed fans from their routers and switches. I'm curious how many others have done that or if they've limited it down to one fan per device. Being a lab, obviously there isn't that much traffic being generated as these were made for. What's everyone's thoughts?
-
Questions about CBAC
Hi *, How to place correctly the command 'ip inspect NAME in|out' ? Example : Inside_Networkfa0/0 CBAC fa0/1Outside_Network From the Cisco website, I can find : 'ip inspect NAME in' on fa0/0 Context-Based Access Control (CBAC): Introduction and Configuration [Cisco IOS Firewall] - Cisco Systems From the Packetlife website,…
-
Router and switch can't ping host
I have a new pc at work and setup a new static ip (the same as my old pc). Have it setup as a tftp server. The 2811 and 3750 can't ping my pc but the pc can ping both. Its really weird I can upload and download software from the tftp server but can't ping it. It works so its not a big deal but can't figure out why its not…
-
Strange serial port operation
I have a 2514 router that has serial port S0 to be acting up. If I configure it to be the DCE end, the port remains in a down/down state and the other router shows the port bouncing up and down. If I make the other router the DCE end (switch cable and clock rate), both ports move to an up/up state and stay solid. Not a big…
-
WAN's
What do i need to know for WAN ? Because i saw the CCNA exploration CD from Cisco and it has many things like ADSL, PSTN, ISDN do i need to know these for the CCNA exams ?
-
Routing question (Potentially dumbing, be carful)
Hey, Getting ready for the ICND1 and fired up packet tracer to get familiar with the CLI (again). I had issues with something like this before, and once I got it everything clicked in place, and I had a beautiful network going on PT. I have tried finding the info online and the fact I cant find it at all is frustrating (It…
-
Anything other then knowledge needed for the exams
Was wondering once the CCNA exams booked, do you need to take anything with you? Like ID or anything? or do you just show up on time?? Im looking to book at Taitec in Manchester, i was told they have old machines but should work fine, and have also been told that the marker they give you at the beginning normally doesn't…
-
Mta + ccent?
So while im studying for my CCENT i was looking at microsoft certs and came across the MTA:network fundamentals I did some research and found its similar to Net+, with that in mind do you think its a good idea to take the MTA network fundamentals while im studying or just to focus on the CCENT, trying to look at it to kill…
-
Question
Do i get with pdf a wallet ccent ID ?
-
Help with lab
Hey guys, ive recently purchased a few bits of gear for my ccent lab, i purchased some layer 3 switches so i can keep them for ccnp aswell. Im just getting into all of this, so im pretty new. I am just curious on the best way to set this up and also connect it up to my current home network. Im guessing i am ok to buy a…
-
Trying to re up my CCNA
Hey guys, Been a long time since i've been on here. Just wanted to start saying how much i miss this forum and how this place helped me get started. I've been working in Networking for over 5 years now and it all started here. I got my CCNA years back and have been so busy doing work that i never continued on with my…
-
ICND1 pass!
Yay! Now studying for my ccna then might spend some time with voice or security? I have interest in all. Suggestions on path? Ccent, ccna, ccnp Ccent, ccna, ccna voice Ccent, ccna, ccna sec Also have interest in SNIA and RHCE Career goal is network Eng or Noc tech :) I love it all.... decisions hmm Also, how long does it…
-
CCNA Game
Just found this last night and it's great! I know it's not free, but it's worth the small amount. I haven't checked if there's an iOS version or anything like it, though I'm sure there is. Currently has two games and more coming. Just figured I'd post it in case anyone's been looking for something like this! Enjoy!…
-
Beating my head around trying to set up Remote Connection my Lab
Can anyone give me a step by step on what I need to do to set up a successful connection to my Home lab? I have a 2511 and 4x 2600XM routers with 3x 2950 switches. My internet connection is Cable from wall > Modem > Linksys Wireless Router w/ 4 ports Currently I just have my lab set up on it's own and haven't tried…
-
What is possible once CCNA is complete?
Hi All, At the moment I'm in a 2nd/3rd line IT network support job with 10% exposure to Cisco kit. I'm currently studying for the CCNA course, once completed what kind of jobs can I go into? Want to know all options available? Regards
-
Route Summarization question??
Any tricks to solving this type of problem quickly. I really don't want to right all the ip routes in binary. Then solve problem. What is the "Magic trick" besides doing it the long way. I tried looking on YouTube, but everyone teaches it the long way. I know someone out there figure a quicker way. Writing stuff out in…
-
Writing while studying
I think I am way too heavy on writing as I study. It's killing me Am I the only one who begins reading a topic and start writing down random things to the point you think "@$#! this is a lot of writing"? I think I am going to stop writing and just read for awhile.
-
INE CCNA & CCNA Voice video Streams are back
I hope I'm not violating any forum rules, but I just wanted to let everyone about the free streams from INE. I wish these were available when I was preping but i'm on to CCNP now. Good luck to all. I'm not sure when they are ending but take advantage while its free. The INE links are below: CCNA Associate Course - 640-802…
-
To those who dont like the Odom CCNA book...
Apparently there are 2 versions of his CCNA books. The version I have previously talked about is the ICND1/2 "Official Exam Certification Guide" whereas the other is the ICND1/2 "Official Exam Guide". I'll say that the exam guide is very different than the other. I swear its like another author wrote it, and while he…
-
Broadcast Domain and Collision Domain Problem
Broadcast domain probably uses for ARP - Address resolution protocol. And collision domain is the collide the data which sends by two devices on a segment network actually. but my problem is calculating the broadcast domain and collision domain, Somehow there is a strategy to how much needs a collision domain and broadcast…
-
Passed CCNA:Security 640-554 today
Passed this exam this morning, was a bit tougher than I was expecting. But a pass is a pass :) Now what to try next :)
-
Give me a idea
Please anyone can give me some CCENT Chapters First to Last..
-
GNS3 Connecting a Real switch
I saw a post on here about this, only they were using GNS3 on the Ubuntu OS. But I want to do this with Windows 7 I know you run it through the cloud. I am wondering what hardware do I need? Any Special cables or a Special network card I need to install in my desktop to communicate with the switch? I want use the 2950…
-
Cables and kits.com?
Cisco Routers CablesAndKits.com Cisco Routers Can anyone tell me if their Cisco routers come with full Ram? I don't want to buy a router with no ram in it. Also if anyone has purchased a router or switch from them?
-
CCNA (LIVING DOCUMENT) with NETCAD EXPLORATION IV
I am going to be doing a Cisco Exploration class to class(and everything in between) living document for my Cisco IV Exploration 4.0 class in combo with test prep for CCENT/ICND2, starting Monday September 17. I already went through Academy in 2003 so this is just a refresh/test prep push. I plan on being introduced to the…
-
Packet tracer troubleshooting partner
Wondering if anyone out there who uses packet tracer wants to trade a few labs, sort out like a troubleshooting exercise. Im quite confident when it comes to setting up a lab, but when it comes down to troubleshooting its a bit hard because obviously with me setting it up i know where everything is, or where it should be.…
-
Cant't ping accross my router!
From my other topic about setting up my cisco 871w. from the CMD: I can ping my router interface fastethernet 0/1 from CMD: I cannot ping my router interface fastethernet 0/4 <(WAN) The oterhside of my router From terminal connertion at the CLI: I can ping my PC I can ping yahoo.com I can ping 4.2.2.2 I will post a config:…
-
CCNA Interview Questions
Please let me know what kind of questions will be asked at CCNA interview for freshers. Share your interview experience.
-
this is serious problem to me. head is itching
Here guys i just wanted to complete my configuration part within few weeks and starting the real world lab gear at my class actually, i just strucked on this middle part here. Using a packet tracer i just created a network, 1 router connected to 1 switch and switch connected 3 computers and 1 computer is connected via…
-
Best Way to Start Labbing?
I've been reading my CCENT/CCNA book for a bit now, and I'm getting excited about the labbing/experimenting portion. What's the best way to go about starting some lab exercises? Anyone know of any beginner step-by-step sites or starting out videos? I basically have all my lab equipment on the floor unplugged and trying to…
-
IPsec : Why do you combine ESP & AH ?
Hi there, AH ensures authentication & integrity. ESP ensures the same with encryption. In this case, why do you mix ESP & AH if ESP does the same than AH ? Thanks in advance,
-
Cheapest Gateway router for CUCM studies.
What is the cheapest setup that I can use for setting up a Gateway Router for CUCM and CUC. The most I will need is a FXO card with it?
-
Lab sort of setup, need help on the next step
I currently have a 1841 router and two 2950 24 port switches. I was wondering if anyone could suggest any good labs and/or ways to set this up so I can get ready for my CCNA. Thanks!
-
Passed ICND1
I just passed my ICND1 today with a score of 887 Describe the operation of data networks 100% Implement a small switched network 80% Implement an IP addressing scheme ... 100% Implement a small routed network 60% Wlan 100% Security 100% Wan 75%
-
VPN Module
Probably a bit off the CCNA, but what exactly does a VPN module do? For example could I still setup a GRE tunnel between two routers without them having a VPN module, or does the module provide the IOS with the necessary hardware to perform the tunneling commands? Does it also provide encryption services?
-
CCNA Service Provider Operations?
Anyone here have the CCNA Service Provider? or Service Provider Operations? if so would you recommend getting them? or can you explain the difference between them in stupid dumb dumb terms to me?
-
New certs
Looks like cisco just announced some new technician level certs. Looks like more aimed at practical/hardware level. From first link below "onsite support and maintenance of Cisco networking devices" CCT RS Cisco Certified Technician Routing and Switching CCT TP Cisco Certified Technician Telepresence - need CCT RS first…
-
Subnetting Multiple Locations
Ok, I have this question(unfortunately nobody to ask or subnetting book). IP Address 135.126.0.0 Three locations Science Lab - 10 hosts, English Department 15 hosts, Tech Ed 3- 20 Hosts (all three locations have a circle around them, including the signal path to English Department and Tech Ed.) Address class- B Custom…
-
Think I need to configure my DNS server correctly, what do you think? Config in post.
I have a 871w: It is connected directly behind my Modem that I have Comcast service connected to. At CLI: I can ping 4.2.2.2, 75.75.76.76, and many other ip's. At cmd: ipconfig /release | /renew, I reciev a ip, and a gatway address. I think I have DHCP, NAT, and PAT configured correctly, but I am pretty sure my trouble is…
-
Questions about CCNA/Time
hello everybody i have couple questions about ccna studying and time frame here is my question: 1- how long it would take a noob to study for a ccna tests, studying 2 hours a day ? i work full time so its harder to study more than 2 hour a day . 2- i willl be using cbt nuggets ccna training videos? is it enough or i will…
-
My setup......just because everyone else has a thread...lol
Sorry for it being junky but long nights...lol. This is my humble setup...I'm running a 2 site topology because other parts are needed for the 2811 on top. PSTN - 3725 HQ - 3825 with a NME-16ES-1G-P with the latest 3750 image BR1 - 2811 BR2 - 2811 Random routers - 2 2851s Phones - 7961GE, 7961, 7970, and 7941 ESXi - This…
-
Ccent study material
Book: Exam Prep CBT Nuggets 1-2950 switch 2-1721 routers Will this be enough to pass the CCENT in 2 Months ? Chirstmas Present to myself.
-
how much does the icnd1 exam cost
i cant seem to find the price anywhere my work will pay for the exam if i pass and need to know how much it costs? i live in the uk thanks in advance
-
CCNA CBT Nuggets study question
I am studying for my CCNA and starting with the CBT nugget videos. I read on the forums here that it is best to watch all the videos then after read the study books Odom or Lammle. My question is, when Jeremy gets into Cisco's command line and starts setting up the switch and or routers should I be doing them with him or…
-
Hardest CCNA Security topic?
What do you think the hardest CCNA Security topics or configs are?
-
Is CCNA Discovery Enough for CCENT/CCNA?
As the title states, is it enough for me to get through? Thanks.
-
Free ethernet reference wall poster
they just sent me this email, thought i would share. It looks cool if you have a place to put it, could be useful Free Ethernet Connectivity Technical Reference Poster edit: they have sent me stuff in the past. no garbage no futher junk mail. you can trust FLUKE. just a free poster. If you check send me a free trial…
-
What book is good for CCENT?
I'm currently going for my Security+ which I plan on taking very soon, but I like to start preparing for future exams quickly and I will be preparing the CCENT ICND1 exam right after. The "How to study for the CCENT / CCNA" says to use Odom's or Lammle's CCNA books but I just wanna focus on the CCENT for now. I know Lammle…
-
RIPv2 problem, R1 and R2 do RIP, but R3 does not
R1 and R2 has a dynamic route learned via RIP, but R3 doesnt have it. All 3 router was set up with same commands. I am thinking but i cant come up with what is wrong. Anybody?
-
is pocket tracer a joke?
I was just doing this basic direct route configuration. All i needed to do was interface Serial2/0 ip address 10.1.128.251 255.255.255.0 ! interface Serial3/0 ip address 10.1.130.251 255.255.255.0 and entered same command with just the IP addressed changed accordingly. And when i tried "R0#Show ip route" i get nothing in…
-
router reboots randomly
which logs to check when a router reboot randomly?
-
MY CCNA study material. Is this Enough?
I currently am new to all things Cisco and I'm using the study material below to try and pass the CCNA in 4 months. What do you think? Anything else I need? study flash cars, a test question program, a lab book etc.? I will be putting in 2 hours a day of study time. All helpful advice is welcome. CCNA CBT Nuggets- Jeremy…
-
stuck in a CBT Nuggets lab
I am working on a cbt Lab, all and all I am doing well, but: The part I am stuck: I only have the Comcast home service, I do not have my own IP address. I checked the routing table from my wrt54g, here is my routing table. The wrt54g that I used for my house gateway is 192.168.100.2, I guess you knew that. This is what I…
-
CIR and Access Rate
Reading up on frame relay and it talks about the above being different. I thought the cir and clock rate would be the same? Do they not determine the speed?
-
Terminal Programs
Since all my switches I ordered should be shipped at my house by now I was wondering what terminal programs everyone uses/recommends. All I really know of is PuTTY since it's free and seems to be the most popular. I am wondering what everyone is using and why and preferably the cost if it isn't a free software.
-
640-802 Exam Tomorrow
Sitting for the 640-802 exam tomorrow morning. I'm mostly relying on my experience but did go through a 5 day CCNA accelerated course recently for free using Cisco Learning Credits. Also, used Lammle's book to brush up on the topics I don't use often at my current job. Wish me luck!
-
Subnetting Help
I have a problem that I would appreciate help on. Number of needed subnets = 2 Network Address = 195.223.50.0 Address Class - C Default subnet mask - 255.255.255.0 Custom subnet mask - 255.255.255.128 Total number of subnets - 2 Total number of host addresses - 64 Number of useable addresses - 62 Number of bits borrowed -…
-
Anyway to get the IPS signatures for learning?
Is there anyway you can get the IPS signatures and public key for learning purposes so you can follow along with the book and do the setup? How has everyone been doing the IPS stuff? This is the first real road block I have come across. You can get CCP with a regular Cisco account and the evaluation of the Secure ACS…
-
Help! New Lab
Hy guys, i have just passed CCNA with a score of 920 points. From the CCNA i have : 1 x 2620XM (64/16mb) 3 x 2950 What should i buy for CCNA-Voice?